Question about Cars & Trucks

Open Question

Where does the anti reverse spring go on a shakespeare alpha ALX 2460G go

The spring is a simple oblong loop with a right angle arm about 1/4 inch long

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear wiper will not contact the window enough to clean properly.


get it serviced.
its cave man simple, motor,arm blade. im blind so cant see bent.

if the arm is bent by kids, it will never work right.
the angle is critical.
blade is not arm.
any shop in the world this is childs play
any auto store, will do this for free, guy walks out (kid)
and looks , the arm is bent, says go to jeep . and is right.

Dec 24, 2014 | 2004 Jeep Grand Cherokee

1 Answer

How do I remove the windshield wiper arm from a 1995 chrysler lebaron convertable?


To remove the wiper arm from a 91-94 LeBaron Convertible:
1: Remove the blade first. (Hood up was easier on mine)
2: From under the hood, lift arm high enough so you can get the small tab at the base of the arm to slide back toward the windshield about 1/4 inch. The tab won't move back until the arm is lifted enough to make clearance for the tab. With the tab moved back, it will keep the arm from coming back down if done correctly but BE CAREFUL that the blade doesn't spring down onto the windshield or put a towel down in the area to cushion any accidents!
3: With the tab now pushed back and holding the arm from returning down you can now slide (jiggle) the arm off from the shaft. It may seem still locked on but if the tab is out far enough to catch the arm from returing it is far enough and you just need to wiggle just right or maybe spray some WD-40 to help, but you really shouldn't need WD-40
Installation is reverse of these instructions.

Jun 13, 2012 | 1995 Chrysler LeBaron

1 Answer

How do you release pressure from the tensioner to remove the timing belt on a 2006 chrysler sebring?


it should be on a spring loaded arm that applies tension from that to the belt. on the arm the is a spot where you can use a 3/8 inch socket wrench to reverse the tension and remove the belt.

Feb 10, 2012 | 2006 Chrysler Sebring

4 Answers

How to remove windshield wiper arms?


pull the wiper arm up, pull the wiper back then pull it hard down the wiper arm once the loop releases the wiper.

Mar 09, 2011 | 2000 Saturn L-Series

1 Answer

How do you replace the front windshield wiper blades?


If you grab the arm and pull it toward you gently (it should be spring loaded so you can move it) You can spin the wiperblade all around, sort of like a swivel. On the inside of the ARM, very close to the blade there will be a small black tab just sticking out about 1/4 of an inch. Push down on it and the blade will slide down the arm and disconnect. Once you get it, you will laugh. Very simple.

Mar 05, 2011 | 1999 Lexus RX 300

1 Answer

I replaced the lifters in my 2000 galant 2.4 L and i need to know what to torque the rocker arm shafts to.


1.5 and 1.8 engines:
* Install the rocker arm and shaft assemblies. Tighten the rocker arm shaft retainer bolts to 23 ft. lbs. (32 Nm).

* Check valve adjustment and install the valve cover. Tighten the valve cover bolts to 16 inch lbs. (1.8 Nm) for the 1.5L engine or to 29 inch lbs. (3.3 Nm) for the 1.8L engine.



2.0 engine
* Lubricate the rocker shaft with clean engine oil and install the rockers and springs in their proper places.

* Install the rocker shaft assemblies on the engine. Tighten the bolts gradually and evenly to 21-25 ft. lbs. (29-35 Nm).



2.4 engine

fa2bc50.jpg

Fig. Rocker arm shafts and components-2.4L engine



* Fit the rocker shaft springs from above and position them so that they are at right angles to the plug side. Install the rocker springs before installing the exhaust side rocker shaft and rocker arm assembly.

* Install the exhaust side rocker shaft assembly in the engine. Tighten the rocker shaft mounting bolts gradually and evenly to 23 ft. lbs. (32 Nm).
* Remove the lash adjuster retaining tools.
* Install the rocker cover and tighten the mounting bolts to 30 inch lbs. (3 Nm).

* Reinstall the spark plug wires to the spark plugs.



Hope helps.

Sep 06, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

Rear wiper blade replacement


pull arm back and then push little clip in on the bottom underside of the plastic connector that hold wiper to the arm ,turn blade at right angles to arm and slide backwards ,its simple and easy to do

May 13, 2010 | 2003 Toyota 4Runner

1 Answer

How do you put in a ball joint in a 2001 sebring convertible


It depends on exactly which ball joint of the 3 per side your changing, but here are the details.

COMPRESSION LOWER ARM & LATERAL LOWER ARM ASSEMBLIES
Removal
1. Loosen compression lower arm ball joint nut. Using steering linkage puller, separate ball joint and
knuckle. Remove nut, bolts and compression lower arm assembly. Remove dust cover.
2. Remove stay. Remove shock absorber lower mounting bolt. Loosen lateral lower arm ball
joint and knuckle nut. Using steering linkage puller, separate ball joint and knuckle. Remove nut, bolt and
lateral lower arm assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for compression lower arm ball joint is 4-22 INCH lbs. (0.5-2.5
N.m) for 2000 models. On 2001 models, breakaway torque is 22-54 INCH lbs. (2.5-6.1 N.m). Ensure
breakaway torque for compression lateral lower arm ball joint is 13 INCH lbs. (1.5 N.m). Check compression
lower arm, lateral lower arm, dust covers, and bushings for damage and wear.
Installation
To install, reverse removal procedure. Use NEW ball joint nuts. Lubricate lip and inside of dust cover with
multipurpose lubricant. Using installer, install dust cover. Check front wheel alignment.
UPPER ARM ASSEMBLY
Removal
Using steering linkage puller, loosen upper arm ball joint and knuckle nut. Remove self-locking nut. Remove upper arm and upper arm shaft assembly. Remove dust cover.
Inspection
Using preload socket, ensure breakaway torque for upper arm ball joint is 3-13 INCH lbs. (0.3-1.5 N.m).
Replace upper arm assembly when measured value exceeds specification. Check upper arm, dust cover, and
bushings for damage and wear.
Installation
1. To install, reverse removal procedure. Use NEW self-locking nuts. Lubricate lip and inside of dust cover
with multipurpose lubricant. Using Ball Joint Installer (MB990800), install dust cover.
2. Ensure upper arm shaft assembly is installed at indicated angle. Verify upper arm shaft
assembly installation. Check front wheel alignment.

Once you have the correct arm off and a replacement joint (if available, some are not serviceable and require the arm to be replaced) then you will need a press or a ball joint press to change the joint. Such as
http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=38335

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46389

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=66958

or http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=46967

Mar 17, 2010 | 2002 Chrysler Sebring

1 Answer

I can't locate the starter solenoid on my 2000 chevy silverado. Where is it?


(Starter) Solenoid - Removal & Installation
  1. Remove the starter motor.
  2. Reposition the M-terminal stud weather cover.
  3. Clean the epoxy coating from the M-terminal stud.
  4. Loosen the M-terminal stud nut.
  5. Remove the cable from the M-terminal stud.
  6. Remove the solenoid bolts.
  7. Separate the solenoid from the housing and unhook the solenoid plunger from the drive gear lever.
  8. Note that the spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2).

    335574b.jpg

    Fig. Spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2)
  9. Remove the solenoid housing.
  10. If necessary, remove the solenoid plunger and spring.
To install:
  1. If necessary, install the solenoid plunger and spring.
  2. Using Three Bond silicone 1207B, GM P/N 97720043, seal the starter solenoid attachment area.
    WARNING Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop. Improper installation of the drive gear lever will cause an abnormal or no operation condition of the starter.
    9d089a5.jpg

    Fig. Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop
  3. Install the solenoid, making sure to insert the drive gear lever (1) into the solenoid plunger (2) loop, perform the following:
    1. Pull the gear lever (1) out away from the starter housing and pull the plunger (2) out away from the solenoid.
    2. Tip the solenoid and insert the lever into the loop, push the solenoid against the housing.
  4. Install the solenoid bolts and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Wipe the excess silicone pressed out during the solenoid installation from around the base of the solenoid to make a weather proof seal.
  6. Install the cable to the M-terminal stud between the washers and terminal nut.
  7. Tighten the M-terminal stud nut and tighten the nut to 71 inch lbs. (8 Nm).
  8. Using Three Bond silicone 1207B, GM P/N 97720043, seal the M-terminal stud connection.
  9. Reposition the M-terminal stud weather cover.
  10. Bench test the starter in a free-run condition prior to installation.
  11. Install the starter motor.

  1. Remove the starter motor.
  2. Reposition the M-terminal stud weather cover.
  3. Clean the epoxy coating from the M-terminal stud.
  4. Loosen the M-terminal stud nut.
  5. Remove the cable from the M-terminal stud.
  6. Remove the solenoid bolts.
  7. Separate the solenoid from the housing and unhook the solenoid plunger from the drive gear lever.
  8. Note that the spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2).

    fe8b46d.jpg
    Fig. Spring (3) is positioned against the drive gear lever (1) and the drive gear lever is placed inside the solenoid plunger loop (2)
  9. Remove the solenoid housing.
  10. If necessary, remove the solenoid plunger and spring.
To install:
  1. If necessary, install the solenoid plunger and spring.
  2. Using Three Bond silicone 1207B, GM P/N 97720043, seal the starter solenoid attachment area.
    WARNING Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop. Improper installation of the drive gear lever will cause an abnormal or no operation condition of the starter.
    257f66c.jpg

    Fig. Make sure that the drive gear lever (1) is properly installed into the solenoid plunger (2) loop
  3. Install the solenoid, making sure to insert the drive gear lever (1) into the solenoid plunger (2) loop, perform the following:
    1. Pull the gear lever (1) out away from the starter housing and pull the plunger (2) out away from the solenoid.
    2. Tip the solenoid and insert the lever into the loop, push the solenoid against the housing.
  4. Install the solenoid bolts and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Wipe the excess silicone pressed out during the solenoid installation from around the base of the solenoid to make a weather proof seal.
  6. Install the cable to the M-terminal stud between the washers and terminal nut.
  7. Tighten the M-terminal stud nut and tighten the nut to 71 inch lbs. (8 Nm).
  8. Using Three Bond silicone 1207B, GM P/N 97720043, seal the M-terminal stud connection.
  9. Reposition the M-terminal stud weather cover.
  10. Bench test the starter in a free-run condition prior to installation.
  11. Install the starter motor.

Hope helped with this (remember rated this help) Good luck.

Nov 04, 2009 | 2000 Chevrolet Silverado

3 Answers

Hello i just replaced my clutch master cylinder and the slave cylinder i bleed the lines but i cant get the truck in gear what can i do


did your clutch work ok before you replaced it ? if so recheck the clutch action at the tranny it should move 5-6 inchs when you depress it if not rebleed it ?clutch fork should move if not you still got air in it ?

Aug 25, 2009 | Nissan Pickup Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...