Question about Mazda MPV

Open Question

My Mazda MPV is showing code p0108,p1520,p0710

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

lsteward68
  • 331 Answers

SOURCE: i have a fault code of p0108 what has caused this

Your map sensor, otherwise known as mass air flow sensor is probably bad. You should replace it. it is normally located between the air filter and the throttle body. It senses how much air is going into the throttle body so the car knows how much fuel to inject.

Posted on Jul 07, 2009

  • 130 Answers

SOURCE: I got three error code for my Mazda MPV

P1518- Intake manifold runner control fault- stuck open
p1520-intake manifold runner control fault
p0306-cylinder 6 misfire detected

good luck

Posted on May 11, 2011

ZJLimited
  • 17970 Answers

SOURCE: mazda mpv 2001 code P1520

Hi there Jose:


P1520 indicating problems with the IMRC or Intake Manifold Runner Control system. The IMRC actuator is bolt on top of the right side valve cover next to the radiator. Would check to make sure the electrical connector to it is even pluged in to start with to set this codes.





Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Posted on Jun 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove the stereo on a 1996 mazda mpv


Mazda MPV Dash Trim Removal, Stereo Removal - Auto ...

? 3:38
https://www.youtube.com/watch?v=REoTeVM2S-o
Jul 1, 2013 - Uploaded by Robert DIY
Dash trim removal: 5 minutes. This video will show you how toremove the dash trim piece on the Mazda ...

[PDF]MAZDA 1996-UP MPV - Scosche

www.scosche.com/media/guides/ma381.pdf
164. 1996-UP MAZDA MPV. MINIVAN. RADIO REMOVAL USING SCOSCHE DT-1 TOOLS . FRONT DOOR PANEL. FRONT AND REAR DOOR 61/2" 3-HOLE.

DIY Mazda Car Radio and Speaker Removal, How to Remove

www.carstereoremoval.com/htm/stereoremovalMazda.htm
'96-99* Car Stereo Removal ยท Ford Stereo Removal Tools Stereo Removal Tools. How To Install and Remove Mazda MPV Van Car Radio and Speaker, '89-95*

Jan 31, 2016 | Mazda Cars & Trucks

1 Answer

Mazda mpv 2001 code P1520


Hi there Jose:


P1520 indicating problems with the IMRC or Intake Manifold Runner Control system. The IMRC actuator is bolt on top of the right side valve cover next to the radiator. Would check to make sure the electrical connector to it is even pluged in to start with to set this codes.





Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Jun 06, 2012 | Mazda MPV Cars & Trucks

1 Answer

Car starts and dies, code is p0108


A p0108 trouble code is a MAP sensor error code. To be more specific your sensor has to high a voltage. You may want to try replacing your your MAP sensor. Just be sure to disconnect your negative battery cable before you replace the sensor. If you do not do this you may short out the new sensor. I hope this helps you out.

Sep 17, 2011 | 2001 Mazda MPV

1 Answer

Code P0108


EGR boost sensor malfunction..

Jun 21, 2011 | 2000 Mazda MPV

1 Answer

I got three error code for my Mazda MPV P1518,P1520,P0306.


P1518- Intake manifold runner control fault- stuck open
p1520-intake manifold runner control fault
p0306-cylinder 6 misfire detected

good luck

May 11, 2011 | 2000 Mazda MPV

1 Answer

I have Mazda Mpv 2002 . check engin light on . and show the code p0102


no such code exists in my generic codes ,neither in my mazda codes

Dec 03, 2010 | 2001 Mazda MPV

3 Answers

I have a fault code of p0108 what has caused this fault and how do i fix it on my mazda mpv


Your map sensor, otherwise known as mass air flow sensor is probably bad. You should replace it. it is normally located between the air filter and the throttle body. It senses how much air is going into the throttle body so the car knows how much fuel to inject.

Jul 07, 2009 | 2002 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...