Question about 2005 Jeep Grand Cherokee

1 Answer

Seat belt locked wont pull out

We have removed the cover on the seat belt and cant seem to get it released it just gets tighter and tighter i have a volkswagon 06 passat

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 41 Answers

Check if the roll is in the right position,untight the bolt and move it back and forvard a little and pull the belt gently at the same time,if you are lucky it might come loose.

Posted on Jul 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My passenger side seat belt on my 2000 ford taurus se is locked and i cant retract it. how do i fix this problem with buying a new seat belt retractor


of course it possible to access this retractor , you just need to locate the small round circles in the lower part of trim and gently pry the covers off , screws will be evedent , you will need a 6 mm star (five sided) drive socket wrench to remove the retractor though

Feb 10, 2015 | 2000 Ford Taurus

1 Answer

Pt cruiser stuck middle seat belt


The problem:
The set belt stop has been lost so the seat belt retracts too far when the seat is laid flat. When laid flat the release mechanism lock as it should when not level. So the seat cannot be raised up as the belt is too tight and locked.
The Solution:
1) Push the two little clips to release and remove the headrests.
Pull the grey lever on the right of the seat base, lift seat base up and forward toward the front seat..
2) See two red capped leversat the back of the two seat hinges and lever them to the upward position, this releases the seat.
Rock the very heavy seat unit upwards and lift complete unit upwards.
3) Take it out of the car and turn 180% so that the back of the seat and base are in the upward position and the seat belt will pull out as it should
4) Replace the missing belt locking stop (I used a tie pin permanently fixed using super glue).
5) Fold seat back down and test then either re-fit seat unit or leave out to decrease fuel consumption..

db820222-7ca5-4d7b-8740-b685efc61b17.jpg


0fbf0c49-1712-4359-86dd-ee255a836cfe.jpg


b971a90e-fe2b-4599-ac59-f7dc0a5bba30.jpg

Aug 02, 2012 | Chrysler PT Cruiser Cars & Trucks

1 Answer

How to fix a 2001 vectra seat release


You can try to pull on the belt with the plastic trim piece removed the take a flat tipped screwdriver the release the arm or bar holding the belt in the lock position. Most of these have a spring on them. That spring can fall out. Or sometimes the bar or lock arm may be jammed and needs to be pried loose then lubricated to prevent this from repeating in the future.

Jun 04, 2012 | Holden Vectra Cars & Trucks

1 Answer

Rear passenger seat belt locked in place how do i unlock it when it is rolled all the way up with no slack to pull out?


eremove seatbelt cover, locate the safety lock lead or metal at the bottom of seatbelt assembly, remove the plastic roto that locks , push slightly teh belt and if u think lock is release, slowly pull the belt.

Jun 27, 2010 | 1994 Oldsmobile Cutlass Supreme

2 Answers

How can I un-stick a stuck seat belt. It worked fine last time we used it and does not seem to be twisted. 2001 chevy blazer


If it is stuck in the seat belt clip (meaning its buckled) then that model year had a seat belt buckle recall for failure. If its stuck in the seatbelt retractor and your seatbelt retractor is floor mounted there is a release pin on the ratchet gear. TO access it you will need to remove the plastic cover located at the floorboard next to the door on the side of the car that is stuck. If its a seat mounted retractor this means the retractor mechanism is located within the seat frame. You will need to view the bottom of the seat of the belt and see the anchor point. Seatbelts must be anchored to frame of car. Trace it into the seat back. If its located in the back of the seat you will need to remove the seat cover to the extent to reach the mechanism. This can be located at the bottom of the seat.. but more than likely is located at the shoulder area. The Seat cover (fabric) is removeable via clips located at the base and tucked into the seat (think hidden bra/pant clip style connectors or zipper) If you have leather seats it is a bit more detailed and more difficult to manage the seat covers. Typically your local Chevrolet dealer mechanic can get this done in 10 minutes (based one experience) and quite possibly wont charge you or charge you minimally. The downside to this is if its locked that means the same gear that locks it in an accident was frozen in place somehow and this typically indicates a dirty dirty spring or broken spring mechanism. The locking pin operates on centrifugal force and activates based on speed by which the seat belt is pulled out. (just a bit of knowledge) Good luck

Jun 15, 2010 | Cars & Trucks

1 Answer

Seat belt tighten on bumpy road on 2008 altima.


most seat belts work on a centrifical ratchet.if you pull slow it will extend, if you yank it will lock. when you hit a hard bump you sink into the seat and your seat belt takes up the slack but as you rise withe seat it happens quickly engaging the lock . as this happens over and over the belt gets tighter.

Oct 12, 2009 | 2008 Nissan Altima

1 Answer

2005 Saturn Vue with locked middle seat belt....


You'll need to take the housing cover off the seat belt, from there you should be able to access the tension switch on the seat belt. It sounds like it may be set too high...

Aug 21, 2009 | 2006 Saturn Vue

2 Answers

Rear seat down and wont go back up; locked middle belt


middle seat belt shouldn't have anything to do with it. The seat locks down for stowage in the rear cargo area. you can pull the release handle on the back of the seat to release it back into the up position.

Jul 01, 2009 | 2006 Saturn Vue

Not finding what you are looking for?
2005 Jeep Grand Cherokee Logo

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...