Question about Cars & Trucks

Open Question

Juat shuts down and wont pull but wait a min. or two then will take back off

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22133 Answers

SOURCE: 98 mercury sable starts and

got me racking my one ameoba brain cell this one,and i cant think of anything that i have had like this sort of problem,except once with an old petrol commer truck many years ago,and the problem here was the inlet maniifold was loose.Now as this is obviously an auto then when the engine "kicks " as its dropped into gear then something is causing it to cut out .Now i suggest you check manifold nuts are tight first.Then check all the wiring connectors onto the sensors on the engine ,pulling the rubber covers back and checking the wires are connected and none broken or and undue bending that could have broken the copper inside the insulation.Then check the actual connectors themselves ,ensuring they are not broken or burnt.If you cant find anything then call out your local mobile mechanic as he will no doubt have a plug in tester and when engine cuts out it should show a fault??But if it is one of these sensors then iam at a loose end as to what one would cause this sort of fault because when i was at college we were still taught how to white metal and scrape the big end and crank bearings.Not to walk around with white coats and plastic pervert gloves and all looking like bill gates type nerds who can only talk about gigas and OBDII also wouldnt dream of changing a clutch on a big truck on the side of the road with only a trolley jack and a couple of pieces of 4x4 and a chain.Let alone sort out the truck driver and give him a right hander for burning the clutch out in the first place.

Posted on Jan 31, 2009

  • 2 Answers

SOURCE: 89 blazer shuts off when driving.pull over let sit for couple min

Hello it hapend to me with my car i just replace the crankshaft position sensor !!!

Posted on Apr 05, 2009

  • 1810 Answers

SOURCE: jeep juat randomly shuts of after running for

fuel pump reley is what usually does it

Posted on Jan 03, 2010

  • 11 Answers

SOURCE: My car shuts down when driving around 50mph. It is

It sound like your main relay i had a similar problem like that and it ended up being the main relay is underneath the drive side dash.

Posted on Sep 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turns over and wont start at times when it dont start watee 10 min then it will start


Does it do it hot or cold , after driving the truck for awhile or sitting overnight ? Heat can cause resistance problems , electrically speaking . Have you checked to see if there is spark or fuel pressure when it won't start ? If you narrow it down to one or the other it makes it easier for diagnosing . No Start Diagnostic Basics EricTheCarGuy

Nov 04, 2015 | 2006 Chevrolet Colorado

1 Answer

Hood support rod, ground out on the battery, engine wont run


unplug the neg. and pos. cables for about 15 mins and put them back on then wait 5 mins and then try starting it.

Jan 16, 2010 | 1994 Volkswagen Jetta

1 Answer

1999 Pontiac Sunfire ignition lock cylinder changed but car has anti theft and car wont start. How can I get it to start?


try turning the ignition on try to start then without shutting key off wait 10 mins then shut key off then back on but do not try starting leave on for ten mins then back off turn key back on to run but do not try starting it wait ten mins then if it reset it should crank over and start if not repeat all steps again

Sep 19, 2009 | 1999 Pontiac Sunfire

2 Answers

Trunk wont pull shut.


You have a pull down switch that activates the pull down motor for the trunk lid to close. The manufacture of this part supplies this to Ford & General Motors vehicles. You can go to a Cadillac dealership & purchase this part far cheaper than at Ford. I use to work at a GM dearlership & my neighboring Ford dealer would order this part from me for the cost of mine where less than the cost from Ford. Figure those guys out at Ford. No wonder they don't need a goverment bailout
Frank

May 22, 2009 | 1996 Lincoln Town Car

1 Answer

89 blazer shuts off when driving.pull over let sit for couple min


Hello it hapend to me with my car i just replace the crankshaft position sensor !!!

Apr 04, 2009 | 1989 Chevrolet S-10 Blazer

2 Answers

2002 MERCEDEZ CLK 430 Shut off and wont start for atleast 10 mins wait???


is the check engine light on? if so this will lead you in the right direction once you get the code.

Sep 11, 2008 | 2006 Mercedes-Benz CLK 500

1 Answer

2002 Monte Carlo wont start


sounds like your passlock sensor on the ignition barrel is faulty. you will have to go to the dealer to have it replaced because of the programming after replacement.

Sep 11, 2008 | 2002 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...