Question about Geo Cars & Trucks

Open Question

Timing marks for a "95" geo tracker 16v 4 wheel drive engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 95 geo metro

I just did my 95.
The bottom outside pulley has a little cut in it,and its little.Line that at 5 degrees the 3rd line on the plastic marker.
Now on the cam,there`s 2 marks.use the one that has the nipple under it and line it with the v on the back plate.

and wala.

Posted on Jul 13, 2008

SOURCE: four wheel drive will not work on 1995 geo tracker

You need to take the cover off your hub and clean and grease the lock ring. It is attached to the spring. It sounds as though your hub is rusted open.

Posted on Mar 09, 2009

  • 583 Answers

SOURCE: need torque setting for 1993 geo tracker front

i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"

Posted on Nov 06, 2009

roniecon
  • 6826 Answers

SOURCE: 95 Geo Tracker - Automatic. Starts ok, but when

It needs a fluid change,and filter,in the transmission,also,add a additive called LUBEGUARD from napa auto parts,when you ask for the additive,be sure to get the one for gm,this additive keeps the valve body slick,and moving,this is the problem,your filter,and ,or,the fluid is dirty,and causing hydraulic problems,and valves to stick in the valve body in the transmission.

Posted on Mar 15, 2010

  • 1757 Answers

SOURCE: looking for timing belt diagram on 97 Geo Tracker

Click on the following free, direct Link. It has the Timing Belt Diagrams, including Marks and Instructional Diagrams.

Let me know if this helped...

http://www.2carpros.com/car_repair_information/year/1997/make/geo/model/tracker/1997_geo_tracker_timing_belt_diagram_marks.htm

Posted on Apr 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need timing belt diagram for 95 geo tracker 4x4 auto 1.6 engine


the instructions on all new gates belts have that, and Dayco.

G16 a engine or B engine, the steps are different,
the 8valve ""A" engines needs valves lash set very loose.
G16A (TBI engine 8v) black top engine.
http://www.fixkick.com/t-belt/tbelt8v.html

G16B MPI , 16valve (top of engine shouts, 16 vavles)
http://www.fixkick.com/t-belt/16-fast-belt-install.html

the factory pages are there and the maxed out steps way is there.
every itty bitty steps, and the 15 ways to mess it all up.
see those false timing marks
they used the cam cog wheel on 2 engines, one 3 cylinder other 4.
making this tricky, if not alert.

the tracker the GM badged car has a vin that tells what engine,
vin 6 or VIN U
6 is for 16 valves
and a GM RPM tag on the glove box.
LS5 = 8v
LO1 = 16v
ufiche actual
http://www.fixkick.com/specs/RPO/RPO.html


make sure the bottom crank bolt 17mm head is at
94ft/lbs first or BOOM.

Mar 05, 2015 | 1995 Geo Tracker

1 Answer

Where is the timing mark and what is the firing order for a 1995 Geo Tracker 1.6 5 speed manal transmission?


timing of what, cam or spark,..... why not say the JOB, so we can be on the same page...>???????
ILL GUESS DIZZY timing,
but we use the #4 firing to set the cam..so........??????
DIZZY answer.
8v or 16v , there are 2 engines, for sure.
and both are different. see why here.
1,3,4,2 is both but not the rotor
see here.
the DIZZY rotor
8v is CW
16v is CCW.

not knowing that is doom
and never read the GM book, it lies.
here is the index to all trackers.
http://www.fixkick.com/IGN_timing/index.html

May 04, 2014 | 1995 Geo Tracker

1 Answer

CAN YOU REPLACE A 1995 GEO TRACKER ENGINE WITH A TRACKER ENGINE WITH A CRANK SHAFT SENSOR???


what years? her ill give examples (no 1.8L sports)
in each case keeping original in/exh manifold of origional
this is called, a Long block swap......!
96 to 95 16v ok ( the crank sensor just sets there, doing zip)
96 to 95 8v no go. ( it will run by ECU while have fuel mapping)
95 8v to 96 16v no go ( missing crank sensor and mapping issues)
95v 16v to 96 16v,(missing crank sensor, move it.)

and you can swap any with harness and ecu. and manifolds.

see swaps here
http://www.fixkick.com/SWAPS.html#G16Bswaps

and links to near infintate swap data.

Feb 20, 2014 | 1995 Geo Tracker

1 Answer

Timing on a 95 geo tracker


old post.
G16a (8valve head) or G16b (16valve head)??which one
the 2 option engines are not the same.
first the cam must be timed, or spark is hopeless , due to its being end if the chain if events.
so, is cam belt fresh, 60kmiles or less.
its timed at #4 firing.
http://www.fixkick.com/t-belt/tbelt-index.html
see main menu, click your engine.,

spark is next, and guess what, again 3 engines. but 2 for you.
http://www.fixkick.com/IGN_timing/index.html

see , its all there, and even the factory pages are linked that tool
cam marks #4 firing.
distributor marks are #1 firing,
on all 3 engine, early 90s classes.
the cam cog wheel on your year, will have false markes
and is covered here, totally. (avoid "I" marks)

Jan 28, 2014 | 1995 Geo Tracker

1 Answer

How to find the timing marks on a 1993 geo tracker


on what, spark or cam???
this engine 1 of 2, has cam belt timed
and a distributor timed... know that as a fact;. please.

http://www.fixkick.com/t-belt/16-fast-belt-install.html

that is cam. on 16v only
the pages there cover both engine,, G16a and B.
TBI 8valve and MPI 16v engine.

Jan 24, 2014 | 1997 Geo Tracker 2 Door

1 Answer

Timing marks located for ignition timing


spark
G16B engine has one ,its on the damper pulley and cover scale.
here
step 5 here
http://www.fixkick.com/IGN_timing/16v-procedure.html

if found way off? the cam belt slipped. fix that first.

Jan 25, 2014 | 1996 Geo Tracker 2 Door

1 Answer

Crank and cam postions 94 geo tracker 16v engine


cam timing this is called, on the G16b 16v not 8v.
easy
old post , and common 60,000mile service question.,
see the false cam marks, avoid them !!!

http://www.fixkick.com/t-belt/16-fast-belt-install.html

Jan 15, 2014 | 1995 Geo Tracker

1 Answer

How to find iat sensor for 1995 geo tracker


old post.
some dont have it , 92/93 , 16v MPI
the 95 does,
the 8v is just behind the engine thermostat housing
the 16v is in the air cleaner box.
both are seen here.
8v click real photo here
16v click MAF sensor link. see part 39 there.

http://www.fixkick.com/find-parts.html

Nov 27, 2013 | 1995 Geo Tracker

1 Answer

I need to know witch tining marks do i line up with the timing mark on a 95 tracker the I or E on the cam shaft


Click on the following free, direct Link. It has the Timing + Marks: Belt Diagrams, including for your 1995 Geo Tacker, 1.6L SOHC 4-Cylinder.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1995/make/geo/model/tracker/1995_geo_tracker_timing_belt_diagram_marks.htm

Apr 19, 2010 | 1995 Geo Tracker

3 Answers

I need a diagram of engine timing marks for a 1.6 litre engine


1996 Geo Truck Tracker 2WD 1.6L MFI SOHC 4cyl

2efa731.jpg

Fig.: Before installing the timing belt, position the camshaft sprocket (1) so that the timing mark on the sprocket (2) is aligned with the notch (3) on the inside timing belt cover (4) ...

5a2ee07.jpg

Fig.: ...and ensure that the crankshaft sprocket (1) timing mark (2) is aligned with the mark on the oil pump (3)

For more details, can register in autozone.com (free).

I hope help you with this (remember rated this help) Good luck.

Oct 15, 2009 | 1996 Geo Tracker 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...