Question about Mahindra Cars & Trucks

1 Answer

Mahindra front end loader won't go up. Goes down, tilts down. I think my fluid got low, I put in two gallons, does it need priming? It has the four way joystick control. Four hoses in/ out.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mahindra Master
  • 40,764 Answers

Using the controls will bleed any air out
souns like a piston seal has failed allowing pressure to expand the rod to by pass the piston

Posted on May 13, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 mahindra pik up wont go into low range 4wd


Try replacing the motor on the back of the transfer case that engages high/low, which should fix the issue.

Feb 16, 2016 | Mahindra Cars & Trucks

1 Answer

Loader stuck in down position, the joy stick will not raise or lower loader. The joy stick will work the tilt movme


didnt specify type of machine( generic answer)some machines have an electrical assist joy stick check switchs if hydraulic check the r check fluid level in the hydraulics the tilt uses less fluid to the piston than the lift arms ----check the hydro lines and connections doesnt happen all the time but try bleeding lift lines air or debris in lines

Sep 15, 2015 | Cars & Trucks

2 Answers

Start a car after it has run out of gas?


If you ran the car empty it really only needs at least a gallon even on a hill it will start. Sometimes it takes 2-3 key cycles for full prime. If its still not starting you could have low fuel pressure , fuel pump could be faulty

Mar 02, 2015 | 2001 Toyota Camry

1 Answer

1956 fordson major diesel-has front end loader and backhoe on back. What weight hydraulic fluid should I use in the loader and backhoe systems.


It depends a little on what the temperature is outside. I think I normally run a 10w in my backhoe.

Feb 02, 2012 | Cars & Trucks

4 Answers

The dashboard parking brake light comes on while driving and I have checked to make sure the brake has been fully released. What could be the problem?? It doesn't stay on, it comes on and off.


Look at fluid level, some systems invoke the parking light for low fluid. I presume to confuse you. I think the thinking works like this: When you have full new brakes and full M/C by the time the M/C fluid gets consumes by prake pad consumption, the light goes off. If you replaced the front pads, the fluid gets pushed back into the M/C resovoir, and the light goes out. Bet that you are pretty close to needing pads, presuming no leaks or other issues.

Oct 07, 2010 | Ford Excursion Cars & Trucks

1 Answer

Someone backed into my 01 Ranger and the front bumper tilted, the back end down and the front end in to the underside of the grill with no damage to the grill and the bumper still looks straight how would...


first you have to remove the bumpers, if the reinforcement underneath needs to be pulled then do it, it you think the alignment is good enough then you can put the bumper back again. hope this helps

Feb 04, 2010 | 2001 Ford Ranger Regular Cab

3 Answers

I have a slow brake fluid loss. I think it may from the master cylinder. Are there any seals in the lines that go into the master cylinder unit.


no they are inverted flare fittings no seals check all lines and calipers/wheel cylinders if all are dry remove the vacuum hose from the booster if there is brake fluid in the hose the master cylinder is bad

Sep 24, 2009 | 2002 Hyundai Santa Fe

1 Answer

2004 nissan titan...ran out of gas


Good chance that even on 4 gallons it may not start I would try for more, prime the fuel pump several times by turning the key on and leaving it on for around 5 seconds then shutting it off and repeating, obviously not trying to start. I've had cases where even small FWD cars won't start even on 4 gallons on a 12 gallon tank. The newer fuel pumps are a closed system that only allow a small portion of fuel into the pump housing to keep contamination down. Let me know if after adding a few more gallons it won't start we will trouble shoot from there. Thank you for using fixya.com

Jul 02, 2008 | 2004 Nissan Titan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mahindra Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

L Pfaff
L Pfaff

Level 3 Expert

11573 Answers

Are you a Mahindra Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...