Question about Cars & Trucks

Open Question

EBay return policy's?

Defective cruise control switches sent need to return for working switches!

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: '94 Ford Econoline (RV)... cruise control and horn

You need a new clock spring assembly.

Posted on Jul 10, 2009

Ad
  • 1949 Answers

SOURCE: Drove with cruise control toggle

check relay might be stuck

Posted on Feb 20, 2011

pirata777720
  • 4 Answers

SOURCE: where is cruise control fuse located for 2003 ford focs?

visit http://www.simonfamily.us/FocusEV/Wiring.htm. Good luck !!!!

Posted on Aug 15, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need cruise switch that engages-coast-accerlates


What Cruise Control Does - HowStuffWorks

auto.howstuffworks.com/cruise-control1.htm
What Cruise Control Does - Cruise control is already an amazing system, and it's ... hit the brake pedal, and it won't engage at speeds less than 25 mph (40 kph). The system pictured below has five buttons: On, Off, Set/Accel, Resume and Coast. ... The brake pedal and clutch pedal each have a switch that disengages the ...

How to Use Cruise Control ' eBay

www.ebay.com > ... > Car & Truck Parts > Interior > Switches / Controls
In fact, most vehicles have cruise control as standard equipment, so most ... mustengage the Resume shifter or lever (in most cases it is the same Coast or ... As the vehicle in front accelerates and decelerates, the Adaptive Cruise Control ...

Dec 13, 2015 | Cars & Trucks

1 Answer

My cruise control no longer works on my 2003 Mitsubishi Outlander. What may be the problem?


  1. Disconnected or damaged vacuum lines to main cruise control unit;
  2. Bad or misadjusted brake light switch (most likely);
  3. Defective cruise control switch;
  4. Failed main cruise control unit.

May 14, 2015 | Mitsubishi Cars & Trucks

1 Answer

Cruise control not working


There is a specialty shop in Moscow, ID that will rebuild your module very reasonably. They actually have arepair listing on Ebay, ModuleMaster. Sent them mine, returned in 5 days, reinstalled, perfect.

Mar 27, 2014 | 2009 Volkswagen Jetta 2.5

1 Answer

Which fuse is for cruise control in 2003 ford f150


The fuses for the speed control from the factory are :
Engine Compartment fuse panel #7,
Cab fuse panel Fuses #15, #13, #5

The fuse that goes to the recall part is Fuse #13, 20A

The recall is 05S28. Description: Speed Control Deactivation Switch.
The part number for the recall is : 1L1Z-9F924-AA
The part has a fuse inline that is marked as non serviceable, but 1 revision I saw, it was just an ATM fuse under tape. Not sure if this is the final revision that was used on your truck ( or should have been used ).


The self test for the Cruise Control ( for 00-03 MY, with the CC light on the cluster ) :

With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 19, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Cruise control no working on 2001 f-150 4 x 4 5.4


Did you have the recall done ?
recall 05S28. Description: Speed Control Deactivation Switch.

Try the self test for the Cruise Control :


With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 15, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Cruse control not working does it have afuse


It should have a fuse! check manual in glove box. Also , Brake light out in most newer vehichles keeps cruise from working

Jun 14, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Cruise control is inop-fuse is ok


the cruise control switch itself may be defective, also it may have to do with the wiring to the engine, follow the wires and look for any obvious defects, if none are found, replace the switch (if it doesnt work, you can always return it). also check with your local salvage yard for a replacement switch

Mar 19, 2010 | 1993 Dodge Caravan

1 Answer

Cruise control will not turn on. light on dash use to come on. cruise will not work. checked fuse it is ok


Did you have the recall for the cruise control done ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be the fuse in the recall harness is blown.

Try the Cruise Control Self test :
----------------------------------
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.
----------------------------

If the Cruise Control does not enter self test, the fuse in the recall harness ( if done ) is most likely blown and needs to be replaced.

Feb 02, 2010 | 2002 Ford F150 Regular Cab

3 Answers

Cruise does not work on Ford F150


Once you verify / change the Cruise Control Switch
This is the recall that hickoryy472 posted about ( you can also check on the ford site to see if it is still outstanding, it is free ).
recall 05S28. Description: Speed Control Deactivation Switch.

Another option for testing is to pull the connector on the End of the Master Cylinder, and jumper the 2 pins in the connector together. This is a secondary safety switch, in case the tail lamps go out while using the CC, that the pressure switch will shut off the CC.

Next you can run a self test on the CC :

There is a self test in the cruise control system.
With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

You don't have the stalk GM type CC switch, so clint969's post is good info, just for another manufacture.
The buttons ( if they are the problem ) can be removed from the steering wheel without pulling the steering wheel itself on a Ford.

Start with the recall, and then test the CC, and see if you have an issue still

Nov 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

2001 F150 6 cyl. Cruise control just quit working today. I turn it on and hit set, cruise light flashes and does not stay on. Please Help. M Mitchell


2 things

1. Is your truck in the list for the recall, or did you have it done ?
recall 05S28. Description: Speed Control Deactivation Switch.

2. Run the Cruise Control Self test
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 22, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...