Question about Isuzu Cars & Trucks

Open Question

What size allen key will remove the belt tensioner on a 2004 3.5 liter isuzu rodeo

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Changing serpentine belt on a isuzu rodeo 4x4

the tentioner is above the alternator

Posted on Oct 19, 2008

  • 19 Answers

SOURCE: serpentine belt install 2001 isuzu rodeo 2wd 4cylinder auto

I believe that you need a 14MM or 15 MM wrench a long one would be the best since the spring is hard to move. There should be a nut on the tensioner pully #6 on the picture below. This is where you need to move the tensioner with one hand and pull the belt off with the other. It might be easier with 2 people. Remember the belt routing it will help when installing the new belt. Good luck.

Posted on Jan 09, 2009

  • 548 Answers

SOURCE: 1997 Isuzu Rodeo Belt removal

You need to loosen the alternator so the belts become slack. Look for bolts on top and bottom that attach the alternator to a bracket or the engine block. Loosen them and the alternator will move. Since the belts hook to other accessories, you may need to loosen them too. To get them back and the proper tension, you'll need a large screwdriver or pry bar to put tension on them as you tighten the bolts. I suggest you get a Haynes guide for this model that will have photos showing how this is done.

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: waht size allen key to remove front brake calipers

On my Golf 1.9TDI (2005) both top and bottom Calliper fastenings have a 7mm Allen bolt thus you will need a non standard 7mm Allen Key not 12 point

Posted on Jun 02, 2009

  • 9 Answers

SOURCE: 2000 isuzu rodeo removal and installation of serpentine belt

All u need to do is put a wrench on the tention pully and turn it clockwise... this will relive the tention take off the old belt ....put on new one. repeat relive pressure again ...slip it on pully... and relese tention..... done! :)

Posted on Jun 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replaced an air compressor belt on a 97 Isuzu rodeo 2.6 liter


  1. release tensioner
  2. remove belt
  3. put new one on
  4. re tension it.

the tensioner
has a mount bolt
and a spring to the mount.
loosen the bolt
and the spring relaxes
take the belt off
the put new belt on.
then with a large screw drive or lever.
pry the pulley, mount so that the full tension is not applied
to the belt (spring loaded)
lock down the base bolt.

see the slot below, that is the adjustment to make.
there are many engines used, and many tensioners. used.
i think this is 2.6L below.
SKF and BECK both sell this kit. if bad,
if seized or bearings loose as goose its bad. many are.
most are this old. (hopeless if old it will be)
1997 Isuzu Rodeo Timing Belt Tensioner - SKF W0133-1624437
here is the SKF P/N>
the spring is not shown, its considered a separate part.




25805177-swqotypbgb5xpuualtdrxcxo-3-1.jpg

Aug 01, 2015 | Isuzu Cars & Trucks

1 Answer

My 95 rodeo is ticking and i thought it was the timing tension pulley so i pulled it off but its still good is there a spring that puts tension on it


The tension pulley for the timing belt does not use a spring. There is a self-contained hydraulic PUSHER that is mounted to the left of the crankshaft pulley that engages the tension pulley.

If you pulled the tension pulley off and can't remount it, you will need to remove this pusher, retract the pin, hold it in place with a 1.5mm allen wrench, reinstall the tension pulley, reinstall the pusher, then remove the 1.5mm allen wrench to set the tension again.

Make sure the timing belt is still in the right place by looking at the markers at the crank and cam shaft areas.

The original ticking noise was probably from the valves needing reworked.

Apr 06, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

My 1998 isuzu rodeo has been running very poorly, then it will run fine. Someone told me it is the intake manifold gasket. It has been doing this for awhile. The serpentine belt broke as well. I believe...


NO!. tensioner has bearing to make it roll. just remove the belt to make have full access to the tensioner. then remove the bolt on center of tensioner. once it was removed you has a free hand to change bearing.

Dec 26, 2010 | 1998 Isuzu Rodeo

1 Answer

Need a diagram on how to in stall a serpentine belt on a 99 isuzu rodeo v6 with air conditioning


Remove the upper radiator shroud. Remove the fan by undoing the 4 bolts that hold it to the water pump. Using a wrench turn the tensioner pulley hex nut to release tension on the belt. Remove the belt and replace with a new one. Refer to diagram for routing detail. http://www.fixya.com/support/r5914885-isuzu_serpentine_belt_routing_diagram

Sep 07, 2010 | 1999 Isuzu Rodeo

1 Answer

What are the timing marks for 1996 Isuzu Rodeo 3.2 ?


timimg marks for camshafts are notched in the top of the cylinder head. they shuld line up directly in the middle of the 2 smaller cam gears behind the new belt should come with lines on it to make it easier crank to be lined up with keyway slot to the right again the belt should have a ditted line on it for that remember remove the tensioner pushrod assembly and put it in the vice to depress it line the holes up in the body of it and put a 1/4 in allen key through it when you refit remove the key turn it over twice all good

Jun 07, 2010 | 1996 Isuzu Rodeo

1 Answer

Timing belt or chain


timing belt and tensioner

Feb 06, 2010 | 2004 Isuzu Rodeo

1 Answer

Water pump replacement 96 isuzu rodeo


Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Jul 03, 2009 | 1996 Isuzu Rodeo

1 Answer

1997 Isuzu Rodeo Belt removal


You need to loosen the alternator so the belts become slack. Look for bolts on top and bottom that attach the alternator to a bracket or the engine block. Loosen them and the alternator will move. Since the belts hook to other accessories, you may need to loosen them too. To get them back and the proper tension, you'll need a large screwdriver or pry bar to put tension on them as you tighten the bolts. I suggest you get a Haynes guide for this model that will have photos showing how this is done.

Jan 11, 2009 | 2002 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...