Question about Jaguar X-Type

1 Answer

How do I remove fitting from my expansion tank to bleeder hose on my 99 xj8 jag

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jaguar Master
  • 714 Answers

Squeeze the clip which should enable you to pull it off

Posted on May 13, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timeing chain removal 98 jag xj8 4.0


1997 Suzuki Sidekick, JAG Xj8 4.0L
that must be a tiger to keep under control.

Feb 18, 2014 | 1997 Suzuki Sidekick

2 Answers

How do I replace the coolant reservoir?


Most all of them are held in with a few screws that are often very hard to find.
Often you must remove all kinds of stuff like other parts and wires and hoses because they are in the way. Some also have a few screws and a "slide", meaning they have a groove in them, or perhaps they fit into a groove.
Be blessed.

Mar 23, 2013 | 1992 Mazda Protege

1 Answer

Runs hot after i put antifreeze in it


more than likely you have air in the system,,,make sure you take the bleed valve fitting out of the expansion tank feeder line..crank the car up and turn the ac on wide open.you should see bubbles flowing from the removed expansion feed bleeder screw.When the bubbles stop place the bleeder screw back into the housing.Let me know.

Aug 02, 2011 | 2003 Jaguar X-Type

1 Answer

My 2000 XJ8 Jag's sunroof is leaking on the passenger at the very back. I've noticed that when I close either front doors the sunroof moves up like it is not closed tight. What is the problem?


There are drain tubes fitted to let water run out. The tubes drain out at the rear of the front wheel arches. Check that the tubes are not blocked. The sun roof on my XJ8 is slightly "loose" when closed but is not leaking. Sit in the car and have somebody hose water on the roof to check for the origine of the leak.

Aug 24, 2010 | 2000 Jaguar XJ

1 Answer

99 Jag xj8l stopped shifting low gears, only goes in high gear.


You will need to have your tranny rebuilt or get a replacement. As a mechanic myslef, I have seen this a few times in the Jag XJ series. Those people eneded up having tranny replaced as well.

Sep 28, 2009 | 2001 Jaguar XJ8

2 Answers

2003 Jag S-type engine cooling fan comes on and stays on


try replacing the fan stat, usually on the rad

Apr 25, 2009 | 2003 Jaguar S-Type

1 Answer

Water leaking from top of expansion tank.


have you replaced the bleeder screws? and the expansion tank cap they both have O-rings that compress and will fail over time also check the hose at the top of the exp tank it also has o-rings inside it

Apr 03, 2009 | 2000 BMW 3 Series

1 Answer

How do you vent thermostat on 325E (1985)? I replaced my upper radiator hose and I have a feeling thermostat will not open. Thanks for input on this matter.


There should be 2 bleeder screws in the system, one on the expansion tank, and one on a thermostat housing. Open both screws all the way. Turn the key to the On postion (but dont start the car). Then turn the heater to max heat, but have the fan set at the lowest setting. Fill the expansion tank til coolant comes out of both bleeder screws with no bubbles. After that close the screws (be very careful not to over tighten them!!). Then completly fill the expansion tank. (dont mind the full mark, if theres air in the system, it will drop the level in the expansion tank) And thats it. Drive the car around then check the level.

Mar 01, 2009 | 1985 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...