Question about Dodge Cars & Trucks

Open Question

I am replacing the pickup coils in my 86 dodge b250 van it has two coils wanted to know the gap setting for each coil start and run

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: 1994 dodge ram 1500 5.2L

Code 11 "" No crank reference signal to the PCM. or bad Crank sensor. If no crank signal no spark and signal to the injectors.
Replace as soon as possible.

Posted on Jul 03, 2008

  • 5 Answers

SOURCE: My 2002 dodge ram van cranks/ won't fire

The coil is inside the distributor cap. It is a flat round plastic plate the cap pushes downn on when you put it on, with wires going to it. Disconnect the wire connector, remove the distributor cap, remove the rotor, pull up on the wires till the coil/plate pops off the distributor housing. Replace with new coil, reverse procedure to assemble it all.
Be careful to clean inside the distributor when you have the coil out, as it does not come apart often, and sand and dirt builds up under the shield/plate of the coil, especially in dusty areas, so blow it and wipe it out good. Put the new coil in. Put the rotor on, then the cap.
Replace all this stuff if you have trouble with the coil.
Also, replace spark plugs or clean them, as misfires and mis timed spark can cause one or more plugs to really carbon up fast and bad.

Posted on Feb 17, 2009

  • 1201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

Some dodges have an oblong shaped white ceramic block, either mounted on the firewall or on inner fender well, with wire connections, one on each end, if there is one, replace it.

Posted on Mar 16, 2009

dennymulford
  • 1055 Answers

SOURCE: 86 dodge 250 v8-318 no fire at spark plug, will not start

did you change the main coil and coil wire?if so then check the ing resistor and then the computor box

Posted on Mar 20, 2009

  • 2 Answers

SOURCE: I need to know where

does not have one for ignition system

Posted on Apr 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 94 Dodge B250 Ram van will start and run perfectly until it warms up and then cuts off. What could be causing this?


There is a carburator heater coil that is sticking. It is leaving the truck in warm up mode.

Jan 19, 2013 | Cars & Trucks

1 Answer

1995 Dodge 2500 van no ignition


I have the same issue on a 94 B250 - replaced ECM, cam and crank sensors - still only coil primary with initial relay cycle, then nothing during crank. Was told ECM needs signal from cam and crank to send primary to coil. Very confusing - all wires connected.

Sep 01, 2012 | 1995 Dodge Ram 2500

1 Answer

1990 dodge b250 318 tbi... pulled codes from ecu... results= 12, 21, and 55. Fuel system is very rich causing flooding and stalling. I would appreciate any input you can provide. I also had a problem...


code 21 is for the oxygen sensor. This controls the mixture of the fuel going into the engine. the sensor may be bad or its connector may be dirty or faulty.

Check for proper engine ground and ground to chassis for dirty or loose connections.

Check these items if problem persists after O2 sensor repair.

MAP
fuel pressure regulator

Aug 18, 2011 | Dodge Ram B250 Cars & Trucks

1 Answer

Have dodge van ram 97 wont start when warm .Change coil an module


Won't start or won't turn over? Does it turn over and just crank?

Jan 27, 2011 | 1988 Dodge B250

2 Answers

1984 dodge van has power to the coil but not from the distributer, and it doesnt start. van ran fine until the positive post came off while driving down the road, it just died and hasnt fired back up...


Does the coil produce voltage? I know it has power to it, but is it throwing voltage? if so check the coil wire at the distributor. if power is reaching the distributor but not throwing spark from any plug wires, your problem is a bad rotor and or cap. Or bad wires.

Jun 10, 2010 | 1984 Dodge Pickup 4WD

2 Answers

No fire


Change the cold start sensor.

Jun 01, 2009 | 1998 Dodge Ram 1500 4WD

3 Answers

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start...


if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

May 09, 2009 | 1992 Dodge Ram 150 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...