Question about Cars & Trucks

Open Question

Working a dishcloth pattern and it mentions "pushing a TR stitch to RS of work". I don't know what that is. can you explain? I know that a tr is a triple.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
CRTN
  • 716 Answers

SOURCE: 97 cavalier shifting problem

Its Whats Known As Linkage Its Very Easy To Fix But you'll Need The Manual. Its What Aligns The Transmission And The Reading You See On The Dash Or On The Console. You Can Take It To A Repair Shop And Likely It Will Be About $20.00

Posted on Jan 19, 2009

Ad
chuck943
  • 783 Answers

SOURCE: where and what is a tr/mlp sensor for transmission?

It mounts on driver's side of transmission where linkage is.

Another concern is did water get into the trans.? If so then that could be a problem. The glue that is used to bond the clutches to the plates in the tranny is water soluable,in other words it will cause them to unbond. The only fix for that is replacement of the clutches.

Posted on Feb 04, 2009

lilmikew99
  • 122 Answers

SOURCE: Tie Rod on a 99 Pont Grand Prix SC

the inner tie rod should have 2 flat spots where the tool goes onto,then the rest is smooth sometimes very hard too see in there.,the 2flat spots are on the back side close too the rack sometimes you need too put the wrench part of the tool on first then put the outer part of thhe tool onto the other piece .an octopuss would be helpfull with all his arms

Posted on May 11, 2009

  • 316 Answers

SOURCE: Australian Mitsubishi magna tr take off window handle

You need a small hook to get behind the base of the crank and remove the clip that retains the window crank.

Posted on May 27, 2009

  • 15 Answers

SOURCE: Can't replace the TR Sensor on my 1997 Ford Taurus.

Hi; get a stool or ask someone with long arms to pop iy out, make sure that the same you pop it out is the same way you can put it back in, or you will need to reset the gear shift. Good Luck!

Posted on Jun 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Every time I start my 06 equinox the 10 amp backup fuse blows. When I try to restart the car its no crank no start. When I replace fuse it starts fine again. Why is 10amp backup fuse blowing?


A short circuit in the wiring . Do you you know how to test automotive electrical circuits ?
10 amp backup fuse ?????? back up lights ? Video's on youtube showing how to find an fix a short . Park neutral safety switch
The transaxle control module (TCM) primarily controls shift points and lockup engagement.
The transaxle is controlled by an electronic shift system. The TCM processes input signals. From the information received, the TCM controls the transaxle hydraulic system.
The electronic shift system consists of the following components:
• TCM
• Shift Solenoid (SS1 and SS2)
• Pressure Control Solenoid (PSC)
• Lockup Solenoid
• Input Shaft Speed (ISS) Sensor
• Output Shaft Speed (OSS) Sensor
• Transmission Fluid Temperature (TFT) Sensor
• Park/Neutral Position (PNP) Switch

Have the vehicle checked for DTC'S - diagnostic trouble codes
When the TCM detects an invalid combination of TR switch signals, then DTC P0705 sets. DTC P0705 is a type A DTC.

BACKUP Fuse
10A
PNP Switch



The transmission range (TR) switch is part of the park/neutral position and back-up lamp switch assembly and is mounted on the transmission manual shaft. The TR switch is a multi-signal switch. The transmission control module (TCM) supplies voltage to the TR switch. Each gear selector lever position grounds one or more of the signal circuits in a unique pattern. In order to determine the gear range selected by the driver, the TCM compares the voltage combination on the signal circuits to a TR switch combination table stored in memory. Refer to Transmission Range Switch Logic .

Sep 02, 2017 | Cars & Trucks

1 Answer

1992 camaro RS Police interceptor 350 eng code reader Code DTC 22 Throttle Position Low


same this happened with a KIA that I had, and didn't want to spend for a new TPS, since the car was almost new (of course out of warranty, Murphy's Law), assuming that your car has good wires (not broken), to and from the TPS, try to open the tps (sometimes is hard because is encapsulated) inside there is a very delicate brush touching a carbon track in a printed circuit, if possible, very delicate, bend the brushes to make more pressure against the carbon track...
I don't remember which one but one is Grnd, other is +5v, other is signal +, other is signal -,
this TPS has TWO independent tracks, in normally closed throttle, it has 0V signal, and INCREASES with the opening of the tr.
the other has 5V signal that DECREASES with the opening of the tr, at a different rate, thats why you still have tr response, althou sligtly "weird", TPS position is used also to calculate shift points and sometimes the trans changes harshly...

Aug 06, 2014 | 1992 Chevrolet Camaro

1 Answer

2004 MAZDA MPV - troubleshooting code P706, (1) open circuit condition, and (2) failed TR switch


this means transmission range sensor circuit is not communicating correct data to the engine control module (ECM)
P0706 OBD II Trouble Code Transmission Range Sensor Circuit Range... , this link will explain your option's

Jun 08, 2017 | 2004 Mazda MPV

1 Answer

Where is the neutral safety switch located on 1998 ford crown victoria


On 1992 and later models, the neutral safety switch is incorporated into the Manual Lever Position or Transmission Range MLP/TR sensor.

RENOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely on jackstands.
  3. Place the transmission in Neutral.
  4. Remove and discard the manual control lever nut, then remove the lever from the transmission.
  5. Detach the TR sensor electrical harness connector, remove the TR sensor retaining bolts, then pull the TR sensor off of the transmission case.
To install:
  1. Position the TR sensor against the transmission case and loosely install the 2 retaining screws.
  2. Attach the TR sensor electrical harness connector.
  3. Use an alignment tool, such as the TR Sensor Alignment Tool T93P-70010-A, to align the TR sensor slots.
  4. Tighten the TR sensor bolts to 80-100 inch lbs. (9-11 Nm).
  5. Position the manual control lever onto the TR sensor, then install the new lever nut to 22-26 ft. lbs. (30-35 Nm).
  6. Lower the vehicle.
  7. Connect the negative battery cable.
ADJUSTMENT
zjlimited_779.gif


Fig. : Adjusting the MLP sensor (click image for zoom)


Park is the last detent when the manual control lever is full forward. Return 2 detents toward the output shaft for Neutral.

  1. Position the manual control lever in Neutral .
  2. Raise the and safely support the vehicle.
  3. Loosen the sensor retaining bolts.
  4. Insert Gear Position Sensor Adjuster tool T93P-700 10-A or equivalent, into the slots.
  5. Align all 3 slots on the MLP sensor with 3 tabs on the tool.
  6. Tighten the attaching screws to 80-100 inch lbs. (9-11 Nm).
  7. Lower the vehicle.
Hope this helps (remember to rating ans leave a testimonial commnet about this free answer).

Oct 11, 2011 | 1998 Ford Crown Victoria

1 Answer

Want to locate censor p0705 on a 2006 suzuki forenza


DTC P0705 - Transmission Range (TR) switch circuit malfunction (short to power supply)

DETECTION CONDITION
• Two or more range signals are input from the TR switch for 12 s or more.

Diagnostic support note:
• This is a continuous monitor (CCM).
• MIL illuminates if TCM detects the above malfunction condition in two consecutive drive cycles.
• PENDING CODE is available.
• FREEZE FRAME DATA is available.
• AT warning light illuminates.
• DTC is stored in TCM memory.

POSSIBLE CAUSE
• TCM malfunction
• Short to power supply in wiring harness between TR switch terminal A and TCM terminal 1D
• Short to power supply in wiring harness between TR switch terminal E and TCM terminal 2C
• Short to power supply in wiring harness between TR switch terminal D and TCM terminal 2B
• Short to power supply in wiring harness between TR switch terminal G and TCM terminal 2E
• Damaged connector between TR switch and TCM
• TR switch malfunction


Inspect swtich harnesses and test with OBD scanner reader tool.

Sep 30, 2011 | 2006 Suzuki Forenza

1 Answer

Po705 2001 mustang auto


CODE PO705 IS DTR SENSOR TR SENSOR CIRCUIT MALFUNCTION. POSSIBLE CAUSES, DTR OR TR SENSOR CONNECTOR IS DAMAGED OR SHORTED, DTR OR TR SENSOR SIGNAL CIRCUIT IS OPEN OR SHORTED TO GROUND, DTR OR TR SENSOR SIGNAL CIRCUIT IS SHORTED TO VREF 5V, DTR OR TR SENSOR DAMAGED, PCM HAS FAILED.

Jun 24, 2011 | 2001 Ford Mustang

2 Answers

Need installation instructions to replace SW-6538, range sensor, for 2005 ford focus


only have 2002 right now

SECTION 307-01: Automatic Transmission/Transaxle 2002 Focus Workshop Manual
IN-VEHICLE REPAIR Transmission Range (TR) Sensor Removal
  1. Disconnect the transmission range (TR) sensor electrical connector and the selector lever cable.
  1. NOTE: Failure to hold the shift lever while loosening or tightening the manual shaft lever will transmit rotational torque to the TR switch and shift mechanism.
    Remove the TR sensor (automatic transaxle removed shown).
    1. Remove the manual control lever.
    1. Remove the bolts.
Installation
  1. NOTE: Failure to hold the shift lever while loosening or tightening the manual shaft lever will transmit rotational torque to the TR switch and shift mechanism.
    Install the TR sensor (automatic transaxle removed shown).
    • Loosely install the bolts.
    • Install the manual control lever.
  1. Using the special tool, align the TR sensor and tighten the bolts.
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use air tools on this bolt. Hold the manual control lever while tightening the manual control lever bolt, failure to the manual control lever shaft could occur.
    Install the manual control lever.
  1. s2y~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Check the manual control lever is in position "3" same as "D" position.
    Adjust the manual control lever to TR sensor "D" position.
    1. "1" Low 1
    1. "2" Low 2
    1. "D" Drive
    1. "N" Neutral
    1. "R" Reverse
    1. "P" Park
    • When in position "D" the marks on the manual control lever line up with the marks on the TR Sensor.
  1. Connect the selector lever cable and the TR sensor electrical connector.

May 23, 2011 | Ford Focus Cars & Trucks

1 Answer

Where exactly is the switch under the 1997 taurus GL that controls the back up lights?


here on top of the transmission:


jturcotte_338.gif Fig. Fig. 1: Remove the two TR sensor retaining bolts


jturcotte_339.gif

Fig. Fig. 2: Align the TR sensor slots using TR sensor alignment tool T92-70010-AH or equivalent

  1. Disconnect the negative battery cable.
  2. Place the shift selector into NEUTRAL .
  3. Remove the air cleaner outlet tube and the air cleaner housing from the vehicle.
  4. Detach the electrical connector from the TR sensor.
  5. Remove the retaining nut and detach the manual control lever from the TR sensor.
  6. Remove the two TR sensor retaining bolts and remove the TR sensor from the transaxle.

To install:
  1. Make sure that the shift selector is in NEUTRAL .
  2. Place the TR sensor onto the transaxle and loosely install the retaining bolts.
  3. Align the TR sensor slots using TR sensor alignment tool T92-70010-AH or equivalent.
  4. Tighten the TR sensor retaining bolts to 80-106 inch lbs. (9-12 Nm).
  5. Attach the electrical connector to the TR sensor.
  6. Attach the manual control lever to the TR sensor and tighten the nut to 98-141 inch lbs. (11-16 Nm).
  7. Install the air cleaner housing and the outlet tube.
  8. Connect the negative battery cable.
  9. Verify that the engine will only start in NEUTRAL or PARK

Nov 28, 2010 | 1997 Ford Taurus

1 Answer

Need to know location and how ro remove a


  1. Remove the Battery
  2. Remove the battery tray. You need to do this to access the TRS(transmission Range Sensor) If its 2.5 liter you need to also remove the air cleaner, and the battery box bolts(on bottom of box)
  3. Detach the battery positive cable push pin from the battery box.
f040794.gif
4.Raise and support the vehicle.
5.Disconnect the horn and left-hand front fog lamp electrical connectors. Detach the wiring harness from the securing clip.

3c42437.gif
  1. Lower the vehicle.
  1. Disconnect the battery junction box (BJB).
    1. Remove the cable ties.
    1. Unclip the BJB.
    • Position the BJB to one side.
    • 07ac510.gif
      1. Pull the horn and front fog lamp wiring harness through the hole in the battery tray.
      1. Detach the wiring harness from the pin-type retainers in the battery tray.

ee5813e.gif 12.Place the vehicle in NEUTRAL.
13.Remove the transmission range (TR) sensor.
  1. Disconnect the TR electrical connector.
  1. Remove the bolts.
  1. Remove the TR sensor.

31134fd.gif Special tools: TRS Alignment Tool
307-351 (T97L-70010-A)

I hope this is concise enough for you to change your sensor..Take care..Hey did I mention this information I posted is FREE!!!

Mar 21, 2010 | 1998 Ford Contour

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...