Question about Nissan Cars & Trucks

Open Question

1995 Nissan timing chain cover removal, how to.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 28 Answers

SOURCE: 1997 Cavalier timing chain cover

DO NOT PULL ON IT it does not come out, and that will cause more serious problems. You turn to adjust the timing.

Posted on Nov 17, 2008

Ad
  • 4 Answers

SOURCE: Is there a special tool for a 02 nissan altima 3.5l timing cover

yes

Posted on Apr 19, 2009

  • 173 Answers

SOURCE: i have a 1995 maxima 6 cylinder dual overhead cam

HI you need to remove all the bolts that attach rear cover to block and remove the oil pan to gain access to bolt that hold rear timing cover to upper pan hope thie helps.4163b8c.jpg

Posted on Sep 26, 2009

czaa
  • 4525 Answers

SOURCE: 1995 nissan pickup 4 cylinder timing chain - 256k miles

did u recently buy it used-mite of been already done--how r the other components enginewise-its an old car n theyll be more things--but if u luv it then get a haynes repair manual at the zone

Posted on Dec 30, 2009

  • 80 Answers

SOURCE: I recently replace the timing chain in my nissan

find top dead center on clyinder 1 a good way to do this is take off valve cover and line up cam notch with mark on head check to make sure crank shaft timing also is lined up.Pull out distributor and re install so that the rotor inside the distributor is pointing to number 1 plug wire.(find the number 1 spark plug.You will need to remove the distributor cap.Make sure that the distributor is all the way in when checking rotor position.

Posted on Oct 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the inner timing chain cover on a 1998 Nissan maxima 3.5L


it's extremely difficult,you need to remove the timing chain,all sprokets and then remove all the bolts,some of these are behind the timing sprokets

Dec 21, 2014 | 1998 Nissan Maxima

1 Answer

How to fix water going into oil on 1995 nissan


You might have a cracked timing chain cover, blown head gasket, cracked block, or bad radiator if it has a built in oil cooler. It's hard to say without a cooling system pressure tester.

Jul 31, 2014 | 1995 Nissan Maxima

1 Answer

EILL A DOUBLE TIMEING CHAIN FIT A 2.4L Z24 NISSAN MOTOR THAT HAS A SINGLE TIMEING CHAIN ONIT


need to know the clearance between gears and timing cover they may even have a cover to work at parts store

Oct 08, 2013 | 1995 Nissan Pathfinder

1 Answer

How to replace the timing chain of nissan cefiro v6 2000? its 97 model.


Engine - Timing Chain/Front Cover Revised Procedure
Classification:
EM98-009
Reference:
NTB98-107
Date:
January 15, 1999
GA16DE TIMING CHAIN/FRONT COVER
REVISED SERVICE PROCEDURE
APPLIED ENGINE:
GA16DE
APPLIED MODELS:
1991-94 Sentra (B13) w/GA16DE
1991-93 NX1600 (B13)
1995-99 Sentra (B14) w/GA16DE
1995-98 200SX (B14) w/GA16DE
SERVICE INFORMATION
A revised service procedure for the engine front cover/timing chain has been adopted for the GA16DE. It is no longer recommended to remove the
cylinder head when removing the timing chain/front cover(s). Utilize the following steps when servicing the front cover, timing chain, guides or
tensioner(s)
PARTS INFORMATION
CLAIMS INFORMATION
Please reference the "Revision C" pages of the Nissan "1992-1999 Warranty Flat Rate Information Manual", Section "AG", Op Codes AG12AA,
AG14AA, AG142A, AG143A, AG144A and AG24AA. Also reference Section "CA", Op Codes CA20AA and CA22AA. You will note that the
descriptions and flat rate times applicable to the B13 and B14 vehicles (with GA16DE engines) for these Op Codes have been revised to reflect this
new procedure.
Caution
^ After removing the timing chain, do not turn the crankshaft and camshaft separately or the valves will strike the piston heads.
^ When installing chain tensioners or other sliding parts, lubricate contacting surfaces with new engine oil.
^ Apply new engine oil to bolt threads and seat surfaces when installing the camshaft sprockets and the crankshaft pulley.
^ Do not spill engine coolant on the drive belts.
^ Please refer to the Service Manual for the correct tightening torque.
Removal
1. Set # 1 piston at TDC on its compression stroke.
2. Remove the spark plug wires.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 2
3. Remove the rocker cover (see Figure 1).
4. Remove the coolant reservoir tank with bracket and reposition it for clearance.
5. Support the engine with a suitable jack.
6. Remove cylinder head front mounting bracket.
7. Remove engine front mounting, then the engine front mounting bracket.
8. Remove cylinder head front cover.
9. Remove the upper chain tensioner (see Figure 2).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 3
10. Wipe off the links of the upper timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the cam sprockets and idler sprocket (see Figure 3)
11. Remove the four (4) front cover to cylinder head bolts.
12. Remove side and lower engine compartment splash covers.
13. Remove the accessory drive belts.
14. Remove the crankshaft pulley.
15. Drain coolant by removing the cylinder block drain plug and opening the radiator drain **** (Refer to MA section of the Service Manual).
16. Drain engine oil.
17. Remove intake manifold support of engine front side.
18. Remove power steering pump, pump bracket and tension rod. Position pump aside for clearance.
19. Remove the thermostat housing (See Figure 4).
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 4
20. Remove the lower chain tensioner (see Figure 5).
21. Remove the front exhaust tube. Refer to the "FE" section (Exhaust System) of the Service Manual.
22. Remove the front and rear engine gussets (if equipped) on either side of the oil pan.
NOTE:
On A/T models, remove the rear plate cover.
23. Remove the oil pan (see Figure 6).
a. Insert the Tool between the cylinder block and oil pan.
CAUTION:
Be careful not to damage the aluminum mating face. Do not insert a screwdriver, or the oil pan flange will become damaged.
b. Slide the Tool by tapping it on the side of the Tool with a hammer.
24. Remove the A/C compressor and position it aside for clearance.
25. Remove the A/C and alternator bracket with the alternator.
26. Remove the oil pump drive spacer.
CAUTION:
Be careful not to scratch the drive spacer when removing it.
27. Remove the front cover bolts and front cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 5
CAUTION:
One bolt is located on the water pump (see Figure 7).
*1: Located on engine front mounting bracket.
*2: Located on the water pump.
*3: Located on the power steering oil pump adjusting bar.
CAUTION:
Be careful not to tear or damage the cylinder head gasket.
28. Remove the cylinder block to front cover alignment dowels.
CAUTION:
Do not hit the dowels or the cylinder block will crack.
29. Wipe off the links of the lower timing chain next to the timing marks on the sprockets. Put paint marks on the timing chain, matching them with
the timing marks on the idler sprocket and crankshaft sprocket (see Figure 8).
Installation
1. Install the crankshaft sprocket, making sure the mating marks face the front of the engine.
2. Install the idler sprocket and lower timing chain using the mating marks and the paint marks made during the removal process.
CAUTION:
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 6
Be careful not to tear or damage the cylinder head gasket.
3. Install the lower chain guides.
4. Front cover installation:
a. Using a scraper or other suitable tool remove all traces of liquid gasket from the cylinder block and front cover mating surfaces.
b. Install new crankshaft seal in front cover.
c. Install new oil passage O-rings and apply a continuous bead of RTV sealant to the front cover (see Figure 1).
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install the front cover to the engine.
CAUTION:
Be careful not to tear or damage the cylinder head gasket or oil seal.
5. Align oil pump drive spacer with the oil pump, and install.
6. Install the oil strainer.
7. Install oil pan, referring to "Installation" in the "OIL PAN" section of the Service Manual.
8. Install upper timing chain and sprockets, using the painted reference marks made during removal.
9. Install upper chain tensioner.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 7
a. Before installing the chain tensioner, insert a suitable pin into the pin hole of the chain tensioner (see Figure 2) to hold the tensioner in.
b. Once the tensioner is installed, remove the pin.
10. Install the lower chain tensioner (See Figure 3).
NOTE:
Make sure the gasket is facing the proper direction before installing the tensioner.
CAUTION:
Now rotate the crankshaft by hand. Check that no binding or interference problems occur when the engine is rotated.
11. Install the thermostat housing.
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the engine front cover and the thermostat housing.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 8
b. Apply a continuous bead of RTV sealant to the housing as shown in Figure 4.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
12. Install camshaft sprocket cover:
a. Use a scraper to remove all traces of liquid gasket from the mating surfaces of the cylinder head and camshaft sprocket cover.
b. Apply a continuous bead of RTV sealant to the cover as shown in Figure 5.
NOTE:
Use Genuine Nissan RTV silicone sealant P/N 999MP-A7007, Three Bond P/N TB1207D or equivalent.
d. Install camshaft sprocket cover.
1995 Nissan-Datsun 200SX L4-1597cc 1.6L DOHC MFI (GA16DE) Page 9
13. Apply RTV sealant to rocker cover gasket (see Figure 6a) and install rocker cover, tightening the bolts as shown in Figure 6b.
14. Install the following parts:
a. Crankshaft pulley.
b. A/C compressor and alternator bracket with alternator.
c. A/C compressor.
d. Power steering oil pump and tension rod.
15. Install front and rear engine gussets (if equipped), and rear cover plate (A/T models).
16. Install front exhaust tube.
17. Install upper right engine bracket and mount.
18. Install coolant reservoir tank.
19. Install alternator, power steering and A/C compressor drive belts.
20. Install engine compartment splash guards.
21. Install vacuum hoses, electrical harnesses and connectors.
22. Install spark plug wires.
23. Refill with coolant. Refer to the "MA" section ("Changing engine coolant, Engine Maintenance") of the Service Manual.
24. Refill with engine oil. Refer to the "MA" section ("Changing engine oil, Engine Maintenance") of the Service Manual.

Jan 15, 2011 | 1997 Nissan 200SX

1 Answer

I have a 1995 maxima 6 cylinder dual overhead cam engine,with a blown head gasket on tne number 1 piston.now ive got it torn down up to the front timing chain cover,and ive removed the main timing...


HI you need to remove all the bolts that attach rear cover to block and remove the oil pan to gain access to bolt that hold rear timing cover to upper pan hope thie helps.4163b8c.jpg

Sep 26, 2009 | 1995 Nissan Maxima

1 Answer

98 nissan V6 cam gear chain noise


I don't have a 95 nissan problem, That was a computer generated add on problem that fixya stuck in my question to drive well intended people crazy. I would have joined your service but now it seems like a scam

Jun 11, 2009 | 1995 Nissan Altima

1 Answer

I am replacing the water pump of my 1995 3.0 v6 infinity (same as altima) but my son removed the chain with out marking it, now I need to set the timing. How do I do this? There's marking on the valve...


This should be the same engine as the Maxima. If that is the case, there is no reason to remove timing chain or get it out of time. The pump is driven by the timing chain, but is not "in time".

The pump is under its own cover. The chain tensioner is under its own cover. The pump is removed after the tension is released on the chain, the tensioner pinned in its retracted position to take tension off chain, and the crank is rotated about 20 degrees counter clockwise to slacken the chain at the pump sprocket without coming off the cam sprockets. Then, the pump is remove by removing its mounting bolts and then screwing in three long M8 bolts as jack bolts into 3 holes (carefully and evenly) to jack out pump. The pump is sealed from the engine case by two o-rings that must be replaced. I think the pump mount bolts are sealed with silicone when replaced. I would get a Haynes or other reliable manual.

If you truly have to reset or check timing, definitely get a book.

Jan 12, 2009 | 1995 Nissan Maxima

1 Answer

How to change water pump nissan maxima 1995


Well, waterpump on your car is internal inside the timing chain area, being driven by the timing chain. You need to remove drive belts, the small black side covers, that are screwed into the front engine cover. The left on has the chain tensioner, the right one has the water pump behind it. Once the covers are removed, you need to push the timing chain tensioner inside and put a pin inside of it (tensioner ) to hold it in. Once you have done that, you need to rotate the engine counterclockwise (until you feel tension) to loosen the chain around the water pump. Then you will use 2 bolts (6mm and about 2 inches long) and screw those into the water pump body. This will pull the pump out of the engine, so pretty much the bolts are going to be acting as puller device to remove pump out of engine. reverse install procedure. This is not the easiest of repairs and not for a novice or someone, that doesn't really work on cars. Good luck.

Jul 26, 2008 | 2003 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...