Question about Cars & Trucks

1 Answer

Fuse box diagram 2004 sports trac explorer truck

I dont have a manuel for the fuse box and my interior light not working, and back lights not working

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 12,528 Answers

Visual Inspection Chart Electrical

  • Bulbs
  • Power distribution box (PDB) fuse 35(60A)
  • Power junction box (PJB) fuse 17 (15A)
  • Circuitry
  • Vehicle security module
  • Instrument cluster module
Symptom Chart Condition Possible Sources Action
  • The interior lamps are inoperative
  • Instrument cluster.
  • Vehicle security module
  • Go To Pinpoint Test A .

Principles of Operation
The instrument cluster illuminates the interior lamps when an unlock signal is received from the vehicle security module. The illuminated entry feature will be canceled when any of the following conditions are met:
  • 25 seconds have elapsed since the illuminated entry feature was activated and the interior lamp control is not activated (door ajar or courtesy lamp switch on).
  • The instrument cluster receives a request from the vehicle security module (remote transmitter lock button pressed) and the interior lamp control is not activated.
  • The ignition is in the RUN or START position and the interior lamp control is not activated.
The instrument cluster illuminates the courtesy lamps when any door is open or ajar. The courtesy lamps shuts off when the doors are closed and the illuminated entry feature is not active or when the vehicle speed is greater than 5 mph (8 km/h). The interior lamps are not reactivated until the vehicle speed is less than 3 mph (5 km/h) and a new door open warning lamp signal is received.
The instrument cluster controls the courtesy lamps illuminated entry function by activating the battery saver relay.
The panel dimmer switch is integrated into the headlamp switch and controls the interior lamps by activating the instrument cluster through circuit 1034 (BK/WH).
The vehicle security module sends a signal to the instrument cluster on the UBP network circuit to indicate a request to turn the illuminated entry feature on or off.
The on-demand lamps, glove compartment assembly, homelink module, puddle lamps and illuminated vanity mirrors are controlled by the battery saver relay. The battery saver relay becomes active (relay coil is energized) when the instrument is in the awake mode, or in the sleep mode (relay coil is de-energized).

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceding to the next step.
  1. If the cause is not visually evident, connect the diagnostic tool to the data link connector (DLC) located beneath the instrument panel and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • SCP+, SCP-, ISO or UBP circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics.
  1. If the DTCs retrieved are related to the concern, go to the Instrument Cluster Diagnostic Trouble Code (DTC) Index.
  1. If no DTCs related to the concern are retrieved, proceed to the Symptom Chart.


  2. Instrument Cluster Diagnostic Trouble Code Index DTC Description Source Action B1342 ECU is Defective Instrument Cluster REFER to Section 413-00 . B2499 Courtesy Lamp Output Failure Instrument Cluster Go To Pinpoint Test A . B2659 Courtesy Switch Fault Instrument Cluster Go To Pinpoint Test A . - All Other DTCs Instrument Cluster REFER to Section 418-00 . Do you know what DTC'S are ?

Posted on May 12, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

  • 1861 Answers

SOURCE: I need a diagram for a 2003 toyota corolla interior fuse box

Have you checked to se if there is freon in the system? If there is no freon, the compressor will NOT run.

Posted on Jun 11, 2009

c17hydro
  • 2984 Answers

SOURCE: Need Jeep Fuse Box Diagram

I'll post all 3 and you can decide which style you have:

Pic 1---

415d41c.jpg

Posted on Jun 19, 2009

t955i
  • 30 Answers

SOURCE: Fuse box diagram is not on the cover of the box on

This is the same location as your car img1972uk6.jpg

Posted on Sep 21, 2009

ZJLimited
  • 17970 Answers

SOURCE: i need a fuse panel diagram for my 2002 ford

Check in your Owners Manual or download this document from this link: Ford/maintenance/owners_manuals

Hope helps (remember to rate this answer).

Posted on Apr 11, 2011

Testimonial: "yes thank you, i went to the web site ford gave me and didnt help at all. this was very useful since i didnt get a manual with my truck. "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse panel box diagram for 2010 explorer sports trac


g06304730
F5 5 Rear window motor. Roof opening panel module. Auto-dimming interior mirror unit. Door lock switch, driver side. Door lock switch passenger side. Power window motor, driver side front. Overhead console switch assembly
Not sure if this is what you're looking for. Let me know if it works.

Jul 18, 2014 | 2010 Ford Explorer Sport Trac

1 Answer

How to I disable the airbag on my 2004 Ford Explorer Sport Trac so I can change out the cruise control buttons?


Remove RCM fuse from dash panel fuse box. Fuse F2.10 10 amps. Turn key onfor 30 seconds and see that Air Bag light is lit. Now disconnect battery negative cable for 1 minute, leave disconnected while service is done. now the air bag is disabled. To repower the system turn key on, insert fuse. connect battery, now turn key off for 10 seconds, then turn key on and watch the air bag light. it should go on then after the air bag module is happy that everything is ok, it will turn off.

Dec 06, 2010 | 2004 Ford Explorer Sport Trac

1 Answer

I need to know how to replace the driver side mirror on a 2004 ford explorer sports trac?


a42d43f.gif
By using this diagram, just remove the interior cover by the #1 in the diagram and then unplug the connector and the rest is straight forward.

Mar 06, 2010 | 2004 Ford Explorer Sport Trac

1 Answer

My map light & glove box lite will not work. What fuse is it in the 2007 Sport Trac


Fuse #23 is a 15 amp fuse in the smart junction box. This fuse protects the lights in your question as well as the exterior rear view mirror lamps. the smart junction box is located under dash on driver side kick panel.

Feb 15, 2010 | 2007 Ford Explorer Sport Trac

2 Answers

I need fuse box diagram for 2003 ford explorer sport trac


go to 2003 ford explorer owners manual and download it for free from ford then go to roadside emergencies and you will find the fuse box and power distribution box diagram for all fuses

Dec 16, 2009 | 2003 Ford Explorer Sport Trac

1 Answer

Fuse number for turn signals on a 2002 ford explorer sport trac


It should say it on the fuse box cover. Unless you dont have the fuse box cover anymore.

Aug 13, 2009 | 2002 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...