Question about Cars & Trucks

1 Answer

Go gear is not working properly because , it fall into water

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 604 Answers

It is ruined,your question was answered please stop asking

Posted on May 12, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Have to rev up in gear to get my plymoth voyager to go at all reverse works half the time . When in gear occasionally it will slam like the tranny is going to fall out is there a do it yourself fix

Check your fluid level, you could just be low on fluid and doing irreparable damage to the trans trying to keep driving it. If your fluid lvl is within speck...then it is too late. Your pump is weak and not making enough fluid pressure for the trans to operate properly. you will either need to have it rebuilt or replace it.

Sep 07, 2015 | Cars & Trucks

2 Answers

Driving down the road my 2004 trailblazer when into neutral engine still running fine,now all I have is park but all other gears are neutral

Trans has to out & be taken apart
Internal failure
There are things a shop could check first,
but no reason to come out of gear

Aug 11, 2013 | 2004 Chevrolet TrailBlazer

1 Answer


Hello: If you have a 4 cylinder engine you will need the special tool to hold the drive gear for the water pump. If you don't you the tool you will have a major job. (without using the tool the gear will fall down and the balance shafts will be out of time.)

Jul 19, 2011 | 2000 Saturn SL

1 Answer

Water pump replacement

Hello: If you have a 4 cylinder engine you will need a GM special tool to hold the water pump gear and chain in place. If you dont use the tool the chain and gear will fall down in the oil pan. You will then have a major task in front of you.

Jul 05, 2011 | 2000 Pontiac Grand Am GT

1 Answer

Location of water pump on2001 saturn

Hello: The water pump is located on the back of the engine on the passenger side of the car. You will need a special tool to hold the drive gear for the water pump. Without it the gear and chain that drives the balance shafts will fall out of place. If the balance shafts are out of time the engine will run very rough. You might review a Haynes manual, it may be available at your local library.

Oct 07, 2010 | Saturn SL1 Cars & Trucks

1 Answer

1992 Plymouth Colt Vista AWD Automatic Transmission has only 2nd gear no mater which forward gear selection you make. Reverse is fine. New fluid and filter, no change. The old fluid was not burned or...

make sure all the electrical connectors to the trans are properly connected. One of these plugs is for the shift control solenoids- not properly connected = no shifting. This happened during the repair operation which is why the car worked fine before the water pump was replaced.

Sep 27, 2010 | 1993 Plymouth Colt Vista

1 Answer

When running ac condensation builds & leaks on passenger side under dash.

at the bottom of the evap. the water does fall in a tray like and then into a hose that drain the water out side of the car compartment, the hose is mostly under the hood on the fire wall at the bottom . the hose might be blocked , push a soft wire in and see if it can be clear, or the hose fall in side the car cpompratment, or the casing is leaking
check it properly

Jul 26, 2010 | 1997 Mazda MX-5 Miata

1 Answer

88 dodge shadow idles very ruff. pedal to floor to start.

i have an 88 dodge shadow turbo with a five speed. the car will fall on its face at 5500rpm coming out of first gear. and its rpm range gets lover with each gear. the fuel pressure rises when it fall on its face. the car never dies just falls then picks back up and will fall again unless you keep it under the that rpm. then it is fine. what could be the problem?

Jul 17, 2009 | 1988 Dodge Shadow

1 Answer

Linkage for transmission

Why don't you start by getting the correct linkage. Maybe the tranny you replace is not exactly the same one. No difficult to replace, some of them have adjustments so maybe you might be able to get away with it, by adjusting it properly. Ensure the tranny is in the park position when adjusting, if properly adjusted, all the other gear shift should fall in place.

Oct 11, 2008 | 1994 Ford Explorer Limited

1 Answer

My RPM fall down

That is normal. When you put it in gear, the idle speed drops about 400 rpm.

Oct 21, 2017 | 1996 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80417 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15314 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides