Question about Cars & Trucks

Open Question

How to remove right headlight assembly - Cars & Trucks

Posted by on

  • Spyro Matiatos
    Spyro Matiatos May 12, 2017

    You may want to give more info. Someone may tell you that lawnmowers don't have headlights. ;)

×

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Remove and replace headlight assembly

open hood ,,should see some bolts holding them in place follow the bolts and remove ,,,pull plugs and watch how you remove,,replace light and push back in place and rebolt,,

Posted on Aug 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to Replace Headlight Bulb on 2005 Prius?


Remove fender well trim ( a few screws)
Remove front bumper COVER (not the bumper- the plastic cover)
About 14 screws. Mostly on the underside, get a creeper, and a few
on the top.

Remove the (left or right side) Headlight assembly ( a couple more screws).
One assembly contains the headlight, turn signal and running light. Unplug
the electrical connector from the assembly. All bulbs remove from the back
of the headlight assembly. Headlight is held in place by bail wire, smaller
bulbs are 1/4 turn.

Oct 20, 2016 | 2005 Toyota Prius

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

1 Answer

How do i change the driver side headlight bulb on a 2000 Lexus ES300


  • Open the hood of the ES300 and prop it open.

  • 2

    Look at the headlight assembly from the top down. Depending on your model year, there may be a plastic panel covering the top of the headlight assembly. If this is present, remove it by lifting all of the plastic clips around the edges and lifting it off.

  • Sponsored Links

  • 3

    Locate the three bolts that hold the headlight assembly in place. Two of the bolts are in the left and right rear corners of the assembly, and the third is on the side bordering the outside edge of the car, screwed into the back of the fender panel. Remove all of these bolts with a small adjustable wrench. Though they appear to be designed to be removed with a screwdriver, the way they're arranged makes it almost impossible to remove them with one.

  • 4

    Slide the entire headlight assembly forward a few inches so that you can reach the back of it.

  • 5

    Unscrew the plastic bulb socket assembly. This is the large, round component located right in the middle of the back of the main assembly. Turn it about a quarter turn to the left and you can pull it away from the main assembly. If you're replacing both the bulb and the main assembly, see the next section on how to replace the bulb, then resume this process



  • Read more: How to Change Headlights in a Lexus Es300 ' eHow.com http://www.ehow.com/how_5038522_change-headlights-lexus-es.html#ixzz1x1Ywyhkr

    Jun 05, 2012 | 2000 Lexus ES 300

    1 Answer

    How to replace the ecu on a lexus 300es


    very simple remove the front radiator sheild it should have 6 plastic clips on it. if you dont know wat that is its the big black plastic cover right when u pop the hood. u will see a 10mm bolt on the top of the headlamp assembly remove that bolt you will also see a screw on the other side on top of the parking lamp assembly remove the srew after the screw is removed u will b able to slide out the parking assembly after that has been removed u will see one more 10mm bolt holding the headlight assembly in place remove that and the headlight assembly will slide out after it is out unplug the 3 electrical connectors from the back of the assembly remove the assembly. if u flip it over their will be four screws on the bottom of the assembly remove the four screw and take the plastic plate off u will see a steal box that is ur headlight CM remove the two electrical connectors off the box one of them goes to the headlight twist off the headlight waterproof cap and un plug.. should take you no more than 30mins

    Mar 30, 2012 | 2001 Lexus ES 300

    2 Answers

    How do you remove the headlights off a Pontiac grand am 2004


    Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
    1. Open the hood.
    2. Remove the front air deflector.
    3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
    4. Lift up the headlight retainers to release the housing.
    5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
    6. Disconnect the wiring harness from the headlight assembly.
    7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
    8. Remove the bulb(s)/socket(s) from the headlight assembly.
    To Install:
    1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
    2. Connect the wiring harness to the headlight assembly.
    3. Position the headlight assembly to the mounting panel.
    4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
    5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
    6. Install the front air deflector.
    7. Close the hood.
    prev.gif next.gif

    Feb 02, 2011 | 2004 Pontiac Grand Am

    2 Answers

    How do you replace the front turn signal on a 2005 Buick Terraza?


    Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

    I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

    Sep 07, 2010 | 2005 Buick Terraza

    1 Answer

    Is there a way to replace the horn for a 2004 Malibu


    the horn is easiest to access by removing the right front headlight assembly. to remove headlight assembly, there are to plastic slide pins, just pull up on these to remove assembly.

    Mar 21, 2010 | 2004 Chevrolet Malibu

    2 Answers

    How do you change the front light on the drivers side.


    since i've not personally had a chance to get my hands on this model of vehicle yet, i'm going to make an educated guess based on how it is done on the 02 sierra, since both are gm products. On the sierra there are 2 rods right at where the headlights are under the hood. Remove those rods to release the light bezels, the bezels should be able to be easily removed. from there just remove the bulb from its' socket, disconnect it from the wire, put in the new one and reassemble. Hope this helps

    Mar 10, 2010 | 2005 Chevrolet Equinox

    1 Answer

    Headlight removal


    1) Lift up on the headlight retainer to release the headlight assembly. 2) Release the headlight ball studs from the grommets by pulling the headlight assembly from the lower center corner. 3)Remove the headlight assembly from the upper fascia support. 4) Disconnect the harness connector from the headlight assembly. 5) Remove the headlight assembly from the vehicle. 6) Remove the access cover from the rear of the headlight assembly. 7) Remove the headlight bulb socket from the headlight assembly by rotating counterclockwise . 8) Remove the headlight bulb from the socket. Reverse these steps to install and make sure when your done to adjust the headlight.

    Jun 17, 2009 | 2005 Pontiac Aztek

    1 Answer

    How do I replace the headlight assembly on a 2006 sebring?


    1. Remove the front bumper cover
    2. Remove the upper headlight housing mounting bolt and pushpin
    3. Remove the lower headlight housing mounting bolts
    4. Pull out the headlight housing assembly and disconnect the electrical connector.
    Its pretty easy. Just raise the hood, see the two silver 8mm cap screws on top of the cross member that supports the radiator and fan assembly. Two screws on each side above the headlight housings. The outer screw is right next to the corner of the fender when the hood is raised. Remove the two screws, then the headlight assembly is loose. Just gently pull the headlight assembly forward enought to see the three lamp socket holders on the back side of the headlight assembly. From the outside corner to the inside are first, the parking turn signal, then the low beam lamp and finally the last, the high beam lamp. To remove the lamp socket, push the small plastic locking tab and turn the socket assemby counter clockwise about a half turn and remove the lamp. Now you can replace the lamp and install it back the same way you took it out. Don't touch the new lamp glass with your bare fingers. Oil from you skin will absorb into the glass causing the glass to turn dark and shorten the lamp life. 

    May 04, 2009 | 2006 Chrysler Sebring

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    11 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75822 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...