Question about 2000 Toyota Tundra

1 Answer

2000 toyota tundra 4.7l front axel fell out on passenger side. replaced ball joint , but noticed a metal ring on end of axel seemed a little bent. put everything back together tire has some wobble.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 5,680 Answers

Change cv joint.

Posted on May 12, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front passenger tire fell in while driving


Probably broke the upper ball joint.
If nothing else is damaged the cost of the ball joint is around $25 in most areas plus labor.

Feb 03, 2014 | 2000 Chevrolet Astro

1 Answer

I have a 97 AWD 5.0, I have a single clunck when i back up left or right. I had a leak in my rear pinion which I fixed and I checked the universals at the same time and they fell and look fine. I also...


Without knowing where the noise is coming from, you won't have much luck fixing it. If it happens when you are moving you may have to get someone to stand next to the truck and listen.

Sep 13, 2012 | 1997 Ford Explorer AWD

1 Answer

Replacing axel on passenger side of 2000 hyundai elantra please give a step by step


  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Front wheel
    • Spindle nut
    • Wheel speed sensor, if equipped
    • Outer tie rod end
    • Stabilizer bar link
    • Lower ball joint
  3. Press the stub shaft out of the hub.
  4. Pry the inner joint out of the transaxle or intermediate shaft.

To install:

NOTE

Use new circlips, split pins and self-locking nuts for assembly.


  1. Install the inner joint so that the circlip is felt to seat in the retaining groove.
  2. Guide the stub shaft into the hub.
  3. Install or connect the following:
    • Lower ball joint and torque the nut to 43-52 ft. lbs. (58-70 Nm)
    • Stabilizer bar link
    • Outer tie rod end and torque the nut to 17-25 ft. lbs. (23-34 Nm)
    • Wheel speed sensor, if equipped
    • Spindle nut and torque the nut to 144-187 ft. lbs. (195-253 Nm)
    • Front wheel
  4. Check and/or adjust the wheel alignment.

Jun 16, 2011 | 2000 Hyundai Elantra

1 Answer

Top of front passenger wheel fell inward .what


likely the upper ball joint, but could also be the structure that holds the joint.

Dec 31, 2009 | 2000 Dodge Durango

1 Answer

How to replace right front axle 2000 buick lesabre


Lift the passenger side of vehicle. Remove tire/wheel assembly. Remove the axle nut. Remove the tie rod end nut. Smack the side of the housing the tie rod end goes into to pop the tie rod end loose and out. Remove the sway bar link. Remove the lower ball joint nut. Smack the housing the lower ball joint goes into to pop the ball joint loose. Pry the lower control arm down to pop the ball joint out. swivel the rotor and strut assembly to the side. Pop the axle out. Reassemble in the reverse order.

Jul 05, 2009 | 2000 Buick LeSabre

1 Answer

1996 Dodge 4x4 1 ton leaking pasenger front seal how to replace?


if u have u joints there should not any fluid near your bearing other than grease... if it is leaking anything other than that it is probably brake fluid... i would suggest checking your brake cylinder and brake line leading along side the passenger side

Apr 21, 2009 | 1996 Dodge Ram 3500 Club Cab

2 Answers

Front end Rumble Simalar to worn Ball joint Noise


the problem with your truck is your knuckle bearings. I just replaced them on a friends truck and it sounds like the same problem. Just look on the inside of the front hub close to where the front axel attaches to the hub. If the seal is gone you will have a ring inside the hub on the axel shaft.

Feb 03, 2009 | 1999 Ford F250 Regular Cab

2 Answers

Tundra Ball joint


Call your Toyota dealer; they may be under a recall.

Sep 09, 2008 | 2002 Toyota Tundra

3 Answers

Front end problem


going in drive way noise that most of time upper ball joint you can have a stabilisator link that worn i suject you get that ball joint check again i dont like that noise hope its a fixya for you and me thanks pierre

Jul 26, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
2000 Toyota Tundra Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...