Question about Hyundai Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.
Posted on Dec 31, 2008
No big job Really. Just locate your Drain Plug for the Oil. Thepan is right there, Remove the Bolts around the Pan and Remove. You will lose all of your oil so, Have something there to catch it all. Clean it all around the Edges of the Block where the Pan mounts with Degreaser and Make sure that you Scrape the Old Gasket off of Both the Block and the Pan. Run a Thin Bead of Blue ATV Silicone around the Pan Edge, Lay the Gasket on top of this Silicone. Put another Thin line on top of the Gasket and Reinstall. This Silicone is High Temp Silicone and will Seal Very Well. Make sure to put oil Back in the Motor! Please Rate my Response, I need all the Help That I can Get! Thanks!
Posted on Jan 27, 2009
Tips for a great answer:
Feb 15, 2015 | 2006 Toyota Tacoma
Apr 28, 2014 | 1995 Buick Century
Apr 23, 2014 | 2006 Honda Pilot
Nov 07, 2013 | 2005 Hyundai Getz 1.3
For more oil and oil pump details check
out the direct links below: ---
How to Replace Oil Pan on car?
How to Replace an Oil Pan Gasket?
HOW TO REPLACE AN OIL PUMP
HOW TO CHANGE ENGINE OIL AND FILTER
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
How to Check Differential Oil Leaks and Replace Oil
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
Oil pan Gasket on car?
Oil pressure for car?
How to replace Oil Pan on car?
How to replace Oil Pressure Sensor on car?
How to replace Oil Pump on car?
Car oil leak?
Car oil leaks from valve cover gasket?
Oil light blinks on dashboard?
Oil pressure issues on car?
Oil leaks from air filter on ford?
Wire running from oil pan to alternator?
Why car leaks oil from oil filter?
Why engine is consuming lots of oil?
Maint REQD message on car dash?
Remove Sump oil pan?
Sump not coming OFF?
How to remove the sump on car? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-sump-on-vw-beetle.html
Car oil sump removal diagram?
This will help.
Feb 12, 2012 | 2006 Chevrolet Impala
Jul 29, 2011 | 2006 Cadillac DTS
Jul 28, 2011 | 2006 Cadillac CTS
Mar 18, 2009 | 2006 Hyundai Tucson
Oct 23, 2017 | Hyundai Cars & Trucks
15 people viewed this question
Usually answered in minutes!