Question about Cars & Trucks

Open Question

A mechanic told me the flywheel needs tightening and it needs a special tool

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 94 Answers

SOURCE: My 2001 Pt Cruiser Timing Belt Pulley needs a special tool???????

im guessing a pulley press, or is it the tensoner pulley, usually a rachet head will fit in there, or even a pry bar, if one of the pulleys r bad, what ever you do to get it off, then use a block of wood an a hammer to put new one on,

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace clutch step by step on a toyota rav4 4wd


You need some very specialized tools to do that You'll need a jack to hold the transfer case once you remove all the bolts holding it to the transmission. Remove the drive shafts.Then you'll need to remove the transmission, again with a supporting jack. Once that has been accomplished , remove the bolts holding the clutch to the flywheel. I'd replace the pilot bearing in the flywheel that holds the input shaft to the gearbox before proceeding. There are special tools available to do that. Now assemble the clutch disk and the clutch plate and put the bolts back in without tightening them. Now take the clutch alignment tool and push it thru the clutch disk and into the new pilot bearing. position it so the clutch disk is dead center in the clutch plate and then finish tightening the bolts Put a new throw out bearing on the clutch release lever and reinstall the transmission and transfer case. Reinstall the drive shafts and replace any gear oil that may have spilled out of the transmission or transfer case. Adjust the clutch pedal clearance to spec and you're done.

Mar 30, 2013 | 1996 Toyota RAV4

1 Answer

I need torque specs on flywheel for a 2002 sport trac 4.0


Installation
  1. NOTE: Special bolts are used for flywheel installation. Do not use standard bolts.
    Install the flywheel.
    • Tighten the bolts in the sequence shown in two stages.
    • Stage 1: Tighten the bolts to 13 Nm (10 lb-ft).
    • Stage 2: Tighten the bolts to 71 Nm (52 lb-ft).
please rate, thanks

May 26, 2011 | 2002 Ford Explorer Sport Trac

1 Answer

How to use drive belt fitting tool on focus without tensioner


please explain what you mean by drive belt fitting tool as i do enough of these cars and i never use any special tools other than a flat piece of ally to lock the cams in place.And a big screwdriver to lock flywheel against block to tighten front pulley

Jan 24, 2011 | 2006 Ford Focus

1 Answer

Need a copy of the manual pages, showing how to replace the clutch


Removal & Installation To Remove:
  1. Remove the transmission.
  2. Install a flywheel locking tool.
  3. Remove the pressure plate mounting bolts from the flywheel.
  4. Remove the pressure plate and clutch disc.
To Install:
  1. Insert a clutch disc alignment tool through the disc splines and into the flywheel pilot bearing. Pressure plate balance mark location subaru-07-00-6722.gif

  2. Install the pressure plate on the flywheel with a gap of 120° or more between the "0" balance marks on the flywheel and pressure plate. Hand tighten the pressure plate mounting bolts.
  3. Tighten the pressure plate mounting bolts using a crisscross pattern 12 ft-lb (16 Nm).
  4. Remove the clutch disc alignment tool.
  5. Install the transmission.
prev.gif next.gif

Dec 28, 2010 | 1998 Subaru Legacy

1 Answer

How to i change the bearing on the airconditioner


to change this bearing requires special mechanics tools. This job can quickly become a real pain if the bearing has been staked on. What level is your mechanical expertise? With all due respect if you do not have pullers and access to presses I would not try this project. At the minimum you will need snap ring pliars, a new bearing, a serpentine belt removal tool, a special puller and a press.
First remove the serpentine belt. In the center of the compressor pulley there may be a nut that needs removed, remove it. thread in the special pulley clutch removal tool as far as possible with the center bolt of the puller all the way out. With the tool threaded on tighten the center bolt on the tool until the pulley clutch comes off. this works best if you use an impact. now you should see the snap ring on the center hub. remove it. The hub with bearing should now slide off. If it doesnt you will have to use another special puller. Once you get that off you will have to have the bearing pressed out. Likely the outside race will be staked on. it helps if you can grind those off. A machine lathe works wonders for that job. Once the bearing is off put the new one on with the help of a press and a little locktite. You do not need to restake it as long as it fits plenty tight. the rest of the installation is pretty much the reverse of removal. The pulley clutch will need to be pulled on tight with a special tool with special attention given to the gap. You dont want it to touch but you want the clutch faces as close together as possible. good luck.

Jul 19, 2010 | 1996 Buick Park Avenue

2 Answers

Headgasket is out of this 1997 saturn sc2 1.9 liter


I have changed a head gasket on a saturn 1.9 L engine, no special tools are required. Take your time and be patient. do not over tighten the headbolts and do not forget to torque them to the correct specs. after about a week of driving check everything you tightened to uinsure they remained tight. all should be well when the project is complete. Oh one more thing. a mechanic dropped a socket into a friends engine and blew the motor. be very careful that all of your tools are acounted for before starting the engine

Mar 22, 2009 | 1997 Saturn SC

1 Answer

Torque specs for the flyhwheel of a 1998 toyota tacoma?


Thank you for responding. They figured out by talking to another mechanic what they needed to do. They just didn't know how much torque was needed and since the mechanic didn't know either he told them how to tighten it. It appeared to work. Again I appreciate you getting back to us.

Dec 29, 2008 | 1998 Toyota Tacoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...