Question about 2007 Chrysler Sebring Sedan

1 Answer

2007 Chrysler Sebring 2.7 will Rev 3 or 4 times in a row the pedal on the floor just idle at 2000 what's my issuw

Map sensor and throttle body codes came up

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 78 Answers

Leaking hose to Map or bad TPS, you can test both with meter.

Posted on May 12, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What would cause a 2004 Chrysler Sebring to spit and sputter when you come to a stop


Go to your local auto parts store and get a free OBD2 diagnostic scan. Guessing can cause you to fix something that isn't wrong.

May 16, 2015 | 2004 Chrysler Sebring

1 Answer

97Honda accord idling high. Computer said bad map sensor so I replaced it and still idled high and still says map sensor bad also is locked in park.


You should clean the throttle body and Idle Air control (IAC) solenoid using spray type throttle cleaner. Here's how:

1. Remove the air snorkel which runs from the air filter box to the intake manifold.
2. Have a partner to hold the throttle to the floor (engine OFF).
3. Spray the cleaner into the throttle opening and use a cloth and/or small soft bristle brush to clean the throttle plate and the entire opening.
4. Remove the IAC solenoid (be careful not to lose the rubber O-ring which goes around it - this is a seal and the engine will run terribly without it) and clean its tip with the throttle cleaner.
5. Clean the bore that the IAC fits in to as well.
6. Have your partner to release the throttle.
7. Replace the IAC, air snorkel and any hoses or wires removed during this process.
8. Start engine
**NOTE** the engine will take longer than normal to start because of the "floor" condition caused by the throttle cleaner. Once the engine starts, rev it a few times to burn off the excess fuel/throttle cleaner.


The LOCKED IN PARK PROBLEM
This is due to a faulty or disconnected shift lock solenoid.
It is located behind the left side of the dash near the center console.

Jul 29, 2014 | Cars & Trucks

2 Answers

Have 03 Chrysler Sebring 2.4 Lx with a very high idle. (Undriveable ) replaced the map and throttle position sensor. That didn't work. Any ideas?


your throttle body door is stuck open check the cable from the gas pedel to the throttle body. if anything just to both cables off the throttle body andrun it. if it is the same with cables off when your idle air control valve is bad

Dec 05, 2012 | Cars & Trucks

1 Answer

I have a 2004 Sebring and the idle is running @ 200 0 in park and N .....people say p2p sensor?


i take it you mean 2000 rmp ,,,, not sensor but major air leak after throttle body ,,,,sensor can read what it likes .... no revs without air ,,,

Feb 13, 2012 | 2004 Chrysler Sebring

1 Answer

Chrysler 2000 Sebring will not start


remove the air inlet hose to expose the throttle body, open the flap(simulating wide open throttle) spray carb n choke cleaner in to the engine if the engine start u have a fuel problem, like fuel pump or no injector pulse. if the car still doesnot start then u have a ignition problem, cranksensor or cam sensor etc... they should set a code

Mar 20, 2010 | 2000 Chrysler Sebring

1 Answer

Check engine light stays on all the time(2006 pontiac g5 gt)


check the cam shaft senser i just had 1 put on my chrysler sebring and the engine light went off

Apr 22, 2009 | 2007 Pontiac G5 Gt Coupe

2 Answers

I have a 2000 Chrysler Sebring that wont idle. The car starts and will run only if I step on the gas pedal.


clean the IAC. Use spray carb cleaner and spray the idle air control valve. It is on the throttle body near the throttle plate. It may have become stuck with deposits.

Clean the throttle body as well. Check for vacuum leaks

Feb 05, 2009 | 2000 Chrysler Sebring

1 Answer

Throttle position sensor


its located on the opposite side of the throttle body as the throttle cable. remove the whole throttle body then remove the TPS from it.

Jan 15, 2009 | 2000 Chrysler Sebring

Not finding what you are looking for?
2007 Chrysler Sebring Sedan Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...