Question about Cars & Trucks

Open Question

Adjusting timing belt tention,only one bolt on cam sprocket 2litre hdi citrion dispatch 2003,also where are the timing pin holes for cam and crank

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 205 Answers

SOURCE: "when do i change the cam belt on a peugeot 307 sw diesel"

usually you should do it for peugeot diesel at 122000 miles along with water pump and the tensioner roller that runs under the cambelt too. But to be on the safe side do it at 100000 and save the fortune.
It took me (DIY job) about 6-8 hours as i wanted to save 450 pounds.

Posted on Sep 04, 2009

Ad
john631068
  • 172 Answers

SOURCE: Timing marks on 1999 Ford Ranger 2.5L.

Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

  1. Loosen the alternator retaining bolts and remove the drive belt from the pulleys. Remove the water pump pulley.
  2. Loosen and position the power steering pump mounting bracket and position it aside.
  3. Remove the four timing belt outer cover retaining bolts and remove the cover. Remove the crankshaft pulley and belt guide.
  4. Loosen the belt tensioner pulley assembly, then position a camshaft belt adjuster tool (T74P-6254-A or equivalent) on the tension spring rollpin and retract the belt tensioner away from the timing belt. Tighten the adjustment bolt to lock the tensioner in the retracted position.
  5. Remove the timing belt.

To install:
  1. Install the new belt over the crankshaft sprocket and then counterclockwise over the auxiliary and camshaft sprockets, making sure the lugs on the belt properly engage the sprocket teeth on the pulleys. Be careful not to rotate the pulleys when installing the belt.
  2. Release the timing belt tensioner pulley, allowing the tensioner to take up the belt slack. If the spring does not have enough tension to move the roller against the belt (belt hangs loose), it might be necessary to manually push the roller against the belt and tighten the bolt.

The spring cannot be used to set belt tension; a wrench must be used on the tensioner assembly.
  1. Rotate the crankshaft two complete turns by hand (in the normal direction of rotation) to remove the slack from the belt, then tighten the tensioner adjustment and pivot bolts to specifications. Refer to the necessary illustrations. Make sure the belt is seated properly on the pulleys and that the timing marks are still in alignment when No. 1 cylinder is again at TDC/compression.
  2. Install the crankshaft pulley and belt guide.
  3. Install the timing belt cover.
  4. Install the water pump pulley and fan blades. Install upper radiator hose if necessary. Refill the cooling system.
  5. Position the alternator and drive belts, then adjust and tighten it to specifications.
  6. Start the engine and check the ignition timing. Adjust the timing, if necessary.

Posted on Nov 25, 2009

  • 14 Answers

SOURCE: how to line crank and cam for timing belt on 1988 no crank marks

Hard to explain here... but I believe that car also has the balance shaft which needs to be timed as well. The camshaft has 2 lines which line up to the top of the head, and a "up" or "top" mark at the top.
Crank is set to 0 degrees.

Posted on May 02, 2010

jturcotte
  • 8582 Answers

SOURCE: 2001 2.4l turbo timing marks see marks on cam

everything is at 12 o'clock. see diagram from autozone.com

1515ac4.gif

Posted on Sep 29, 2010

cool78259
  • 228 Answers

SOURCE: timing belt gets loose after

with the belt off negative side of battery disconnected, check

all pulleys especially the ac compressor pulley, make sure they

turn easily and there is no binding, make sure there is no oil

residue or any other liquid on pulleys. make sure you have the

correct belt size for your car and that the belt layout is correct.
good luck!

Posted on Feb 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Set timing on a 98 honda civic dx


"The crankshaft timing pointer must be perfectly aligned with the white mark on the flywheel or flex-plate; the camshaft pulley must be aligned so that the word UP is at the top of the pulley and the marks on the edge of the pulley are aligned with the surfaces of the head.
Install the timing belt over the pulleys and tensioners.
Loosen the bolt used to lock the timing belt tensioner. Loosen, then tighten the timing belt adjusting nut.
Turn the crankshaft counterclockwise until the cam pulley has moved 3 teeth; this creates tension on the timing belt. Loosen, then tighten the adjusting nut and tighten it to 33 ft. lbs. (45 Nm). Tighten the bolt used to lock the timing belt tensioner.
Realign the timing belt marks, then install the balancer belt drive sprocket on the crankshaft.
Align the front balancer pulley; the face of the front timing balancer pulley has a mark, which must be aligned with the notch on the oil pump body. This pulley is the one at 10 o'clock to the crank pulley when viewed from the pulley end.
Align the rear timing balancer pulley (2 o'clock from the crank pulley) using a 6 x 100mm bolt or rod. Mark the bolt or rod at a point 2.9 in. (74mm) from the end. Remove the bolt from the maintenance hole on the side of the block; insert the bolt or rod into the hole. Align the 2.9 in. (74mm) mark with the face of the hole. This pin will hold the shaft in place during installation.
Install the balancer belt. Once the belts are in place, be sure that all the engine alignment marks are still correct. If not, remove the belts, realign the engine and reinstall the belts. Once the belts are properly installed, slowly loosen the adjusting nut, allowing the tensioner to move against the belt. Remove the pin from the maintenance hole and reinstall the bolt and washer.
Turn the crankshaft 1 full turn, then tighten the adjuster nut to 33 ft. lbs. (45 Nm). Remove the bolt used to lock the timing belt tensioner."

" " Chilton Library

Apr 27, 2012 | 1998 Honda Civic

1 Answer

Timing Chain Replacement procedure steps


1. Jack up front of vehicle and support on safety stands. Remove left front wheel.
2. Remove alternator/water pump drive belt. Remove water pump pulley.
3. Remove A/C belt if equipped.
4. Remove valve cover.
5. Remove upper timing belt cover.
6. Rotate crankshaft until No. 1 cylinder is at TDC compression stroke and camshaft sprocket timing marks align with edge of cylinder head. "UP" cast on sprocket will be at top when sprocket is in correct position. Crankshaft may be rotated using a socket wrench inserted through access hole in left fender well (engine rotates counterclockwise).
7. Unbolt and remove crank pulley. Remove rubber seal washers from belt tensioner pivot and adjustment bolts protruding through lower belt cover. Remove belt cover retaining bolts and remove cover from below.
8. Remove concave belt retainer from end of crankshaft. If timing belt is to be reused, mark direction of rotation before removing.
9. Loosen belt tensioner pivot and adjustment bolts. Push tensioner away from belt and retighten adjustment bolt to hold tensioner in this position. Remove belt.
10. Insert a suitable tool through cam sprocket and brace against cylinder head. Remove bolt and pull sprocket from camshaft.
11. Without dislodging key, install new sprocket on camshaft. Torque bolt to 22 ftlb (30 Nm).
12. Install new timing belt by starting at crank gear and working it over cam sprocket in clockwise direction. Ensure that timing marks are properly aligned.
13. Release tensioner by loosening adjustment bolt. After tensioner contacts belt, retighten bolt.
14. Rotate engine at least one full turn (counterclockwise) and check that timing marks are aligned. Loosen adjustment bolt and allow tensioner to take out any remaining belt slack. Torque adjustment and pivot bolts to 22 ftlb (30 Nm).
15. Install remaining components in reverse order of removal. Torque fasteners to following values:

TORQUE VALUES

Valve Cover Nuts - 7 ftlb (10 Nm)
Cam Sprocket Bolt - 22 ftlb (30 Nm)
Tensioner Pivot Bolt - 22 ftlb (30 Nm)
Tensioner Adjust Bolt - 22 ftlb (30 Nm)
Belt Cover Bolts - 7 ftlb (10 Nm)
Crank Pulley Bolt - 83 ftlb (115 Nm)
Water Pump Pulley Bolts - 9 ftlb (12 Nm)

daves944_3.jpg

Dec 19, 2010 | 1983 Honda Accord

2 Answers

1999 honda crv timing belt replace ment instructions and pictures


PATH: Engine Mechanical > Engine Mechanical Components > Timing Belt & Sprockets > Removal & Installation Removal & Installation
  1. Disconnect the negative battery cable.
  2. Position crankshaft so that No. 1 piston is at Top Dead Center (TDC).
  3. Remove the splash guard.
  4. If equipped, remove the cruise control actuator.
  5. Loosen and remove the power steering pump drive belt.
  6. Remove the two bolts that attach the top power steering hose to the power steering pump. Cover and seal the hose and the open port of the pump.
  7. Clamp shut the power steering reservoir return hose, remove it from the return line, and remove the power steering pump and reservoir as an assembly.
  8. Remove the remaining accessory drive belts. Refer to Section 1 for specific details.
  9. Place a piece of wood between the oil pan and the jack, support the engine with a jack.
  10. Remove upper engine bracket.
  11. Remove the valve cover.
  12. Make sure the engine is at Top Dead Center (TDC) for No. 1 cylinder. The engine is at TDC for No. 1 cylinder when:
    • The white Top Dead Center (TDC) mark on the crankshaft pulley is aligned with the raised pointer.
    • The UP marks on both camshaft sprockets are at the topmost (12 O'clock) position.
    • The holes in the No. 1 exhaust and intake cam journals align with the holes in the camshaft. A 4.5 mm or 5/32inch drill bit or Allen key can be placed through the holes to prevent the cams from rotating while removing or installing the cam belt.
  13. Remove the crankshaft pulley. For details, see crankshaft pulley removal in this section.
  14. Remove the timing belt covers.
  15. Loosen the adjusting bolt 1/2-1 turn. Release the tension from the belt by pushing on the tensioner, then retighten the adjusting bolt.
  16. Remove the timing belt.
79245g44.gif

To install:

  1. Be sure the timing marks are properly aligned.
  2. Install the timing belt around the crankshaft sprocket and then stuff a clean rag or paper towel between the belt and the sensor guard to hold the belt engaged with the sprocket teeth.
  3. Place the flat side of the belt clockwise around the top of the tensioner and then engage the toothed portion of the timing belt counterclockwise around the bottom of the water pump sprocket.
  4. Carefully pull the timing belt upward but do notmove the crankshaft. If the crankshaft moved, carefully realign the crankshaft timing belt sprocket with the TDC marks. Carefully engage the teeth of the timing belt onto the exhaust camshaft sprocket, but only install the belt about 1/3 of the way onto the sprocket.
  5. Grasp the timing belt on the toothed side and gently lift the belt enough to begin sliding it onto the intake camshaft sprocket.
  6. Once the belt has started to slide onto the intake camshaft sprocket, slide the belt equally onto both the intake and exhaust camshaft sprockets.
  7. Quickly loosen and then retighten the timing belt tensioner bolt.
  8. Remove the tools from the camshaft caps used for securing the camshafts, and remove the cloth used to keep the timing belt engaged in the crankshaft sprocket.
  9. Apply a clockwise load on the intake camshaft sprocket bolt to remove any slack between the intake camshaft sprocket, exhaust camshaft sprocket and the crankshaft timing belt sprocket, then loosen and retighten the timing belt tensioner adjusting bolt to allow tension to be applied to the belt.
  10. Install the crankshaft pulley sprocket/timing belt guide washer.
  11. Install the lower and upper timing covers.
  12. Install the crankshaft pulley and tighten the bolt to 130 ft. lbs. (177 Nm).

    WARNING

    If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  13. Rotate the crankshaft about 5-6 times counterclockwise to seat the timing belt.
  14. Position the No. 1 piston to TDC.
  15. Locate and remove the rubber plug for the timing belt tensioner on the lower timing belt cover.
  16. Loosen the adjusting bolt 1/2 turn by
  17. Rotate the crankshaft counterclockwise 3 teeth on the camshaft pulley.
  18. Tighten the adjusting bolt to 40 ft. lbs. (54Nm).
  19. Retighten the crankshaft pulley bolt to 130 ft. lbs. (177 Nm).
  20. Install the valve cover.
  21. Install the engine mounting bracket, then remove the jack.
  22. If removed, install the cruise control actuator.
  23. Install the accessory drive belts.
  24. Install the splash guard.
  25. Connect the negative battery cable.
  26. Check the engine operation and road test.

WARNING

Never allow antifreeze, oil or solvents to come into with a timing belt. If this occurs immediately wash the solution from the timing belt. Also, never excessive bend or twist the timing belt; this can damage the belt so that its lifetime is severely shortened.
9d66148.gifeab7aab.gif

Sep 15, 2010 | 1999 Honda CR-V

1 Answer

How do set the timing on hyundai excel 1998


Hi,


It seems you are encountering problems trying to set the timing marks in your elantra,not to worry,simply follow the stepwise solution below;
Ensure timing marks aligned [6] & [7] .

STEP 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets.

STEP 2. Slacken tensioner pulley bolt [8].Push tensioner pulley firmly against timing belt to tension belt.



STEP 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm.


STEP 4. Except Matrix: Turn crankshaft one turn clockwise.



STEP 5. Matrix: Turn crankshaft two turns clockwise.


STEP 6. Ensure timing marks aligned [6] .


STEP 7. Apply a load of 2 kg to belt at .Belt should deflect 4-6 mm. If not Adjust position of tensioner pulley.



STEP 8. Install components in reverse order of removal.


STEP 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm
(7) is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head (6) is crank timing mark,pin mark on crank lines up with markS on block.





Good luck.

Aug 20, 2010 | Hyundai Excel Cars & Trucks

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Need to change timming belt 1997 geo tracker


TIMING BELT CHANGE You should have some mechanical skills before attempting any engine maintenance! These are basic instructions, and you must knoe what you removed, when, and what order so you can reinstall them in order. First, you have to remove everything in the way! You need to remove the Fan, clutch, and shroud, pump pully & drive belts. Next, you need to remove the Crank Pully:

1. Crank Pully Bolt 2. Crank Pully 3. Center Bolt 4. 5mm Hex drive (used to remove pully bolts) Once the fan stuff, and pully(s) are removed, then you need to remove the Timing Belt cover:

Once the cover is removed, you will need to loosen the adjusting nut and pully bolt on the Belt Tensioner:
A. Adjust Nut B. Pully Bolt C. TENSIONER PULLY Once the the Adjust Nut, and Pully bolt are loose, move the pully as far towards the water pump as possible.
Then, you can slip the timing belt from the sprockets. Check the tensioner for roughness and excess play! DO NOT MOVE THE CAM OR CRANK SPROCKETS! IF you do, then you will have to line up the Crank and Cam for piston number one at Top Dead Center before placing the new timing belt on! Note the timing marks on the crank and camshaft sprockets. IF YOU MUST! Allign the Cam and Crank at piston#1, Top Dead Center before removing the belt. Each sprocket has a small hole, with a line through it, and there is a small groove or "V" it alligns with on the engine. Now, once the timing belt is off, look at your new timing belt. Older belts use the Squared off teeth, while new ones have the rounded teeth. Make sure you have the correct belt for your sprockets! Never reinstall a belt that is in questionable condition. BELT WEAR CONDITIONS
If there are Arrows on the belt, they must be pointing to the RIGHT when you put the new belt on the sprockets. If there isn't one, then paint one on, and place the belt back on the sprockets. The arrow will indicate to a mechanic, this is the way the belt must be put back on (if they replace any cam or crank oil seals). Slip the new belt onto the Crank sprocket. While maintaining tension on the side of the belt opposite the tensioner, slip the belt onto the Camshaft sprocket. Releace the Tensioner adjusting nut to allow spring tension against the belt. Temporarily reinstall the crank pully, taking care to align the notch in the pully with the raised area on the sprocket. Rotate the crank clockwise two complete revolutions. Recheck the alignment of the of the valve timing marks. If they do not align properly, loosen the tensioner, slip the belt off the crank pully, align the timing marks, reinstall the belt, and check alignment again. Tighten the tensioner nut, then the bolt. Reinstall all parts removed, in the opposite order, of course. Start the engine and allow to reach normal operating temp, then road test. THEORETICALLY, you should simply be able to replace the belt with the new one, and go, as long as you did not move any of the sprockets when removing or installing the belt. Most people do it this way, and do not test for alignment before replacing everything. When the belt wears, timing will be off, very little, and this is why you check alignment. The belt may have slipped a tooth, making the timing off. This is why the Cam and Crank sprockets must both align properly. An experienced person will do just that: Replace the belt, and go. It really isn't all that hard. It helps to have a second person around with some experience also.

Nov 11, 2009 | 1997 Geo Tracker 2 Door

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

3 Answers

1995 106 d peugeot cranck shaft timming marks on engine


I've uploaded a manual for 106 tud timing belt refitting:
http://www.gigasize.com/get.php?d=y1dnk2hbl8d
may be it can solve your problem

Sep 01, 2009 | 1991 Peugeot 405

1 Answer

99 ford ranger timing belt



Using the same 13mm socket, remove the bolt that you found under the a/c compressor. Look down and to the right of the bolt that you just removed, and you will see two more bolts. Both are 13mm. Easiest way that I found was to go under the driver side tire well, and use 3/8 extensions to reach the two bolts. Once removed, the bracket and the power steering pump should be moved to the driver's side of the frame, and the a/c placed on top of the p/s assy.




Remove the bolts (6mm) that hold the timing belt cover in place. Gently work your way around the cover, and push the tabs in to remove the cover.


Use an impact wrench and 7/8 SAE socket to remove the crankshaft pulley. A SOCKET WRENCH WILL NOT WORK. Once removed, gently tap the pulley with a 2x4 (yes the wooden board) to remove. If you have a gear puller, use that. I don't own one.




Remove the old belt. Now for the alignment. Crank - sprocket on bottom. Use the bolt you removed, and a ½ drive wrench, with the 7/8 socket to turn the crank. Once the keyway is at high noon, leave it alone. Next, move the oil pulley sprocket until the diamonds are aligned. This should put the oil pulley at high noon, also. The camshaft should have a diamond and a triangle. The diamond should go to high noon, and the triangle should align with a triangle on the plastic behind the sprocket. YOU SHOULD REALLY CONSIDER CLEANING THE ENTIRE AREA BEFORE ALIGNING THE SPROCKETS. You cannot align the camshaft without locating the two index (triangle and diamond) marks.


You will also notice a tensioner for the timing belt. You will need to loosen the tentioner with a 13mm and 17mm wrenches. Loosen, then use a cheeter bar bar to move the tentioner over. Lock in place by tightening the tentioner bolts. Place the belt on the crankshaft, move to the oil pulley, then to the cam pulley. Release tentioner, then check the alignment. If correct, reverse the above removal plan, and you should be good.




Don't buy the Haynes manual. I fought with the instructions for this project, and the picture for the timing belt project doesn't show the two indexes for the cam sprocket.



Also, while you are doing this, you should replace the antifreeze if you haven't in the past two years.



Best of luck.

Jul 13, 2008 | 1999 Ford Ranger SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...