Question about Nissan Cars & Trucks

Open Question

Is there only one fuse for rear washer and wiper on nissan note

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 82 Answers

SOURCE: 1998 Toyota Starlet - Windshield Washer not working......ideas?

the washer motor is gone then ,,,its in the bottle,,

Posted on May 08, 2009

Ad
  • 718 Answers

SOURCE: Rear wiper Ford Explorer 1998 won't work.

Look for the fuse for the rear wiper motor is a 15 amp mini-fuse , in location # 8 of your POWER DISTRIBUTION BOX in the engine compartment. Check in the PD BOX for; - relay # 8 is the rear wiper down relay , and - relay # 10 is the rear wiper up relay .

Posted on May 18, 2009

  • 164 Answers

SOURCE: Jeep Liberty 2005 Rear Wiper Not working. Change

could be the arms striped ore the motor shot on it

Posted on Jul 28, 2009

alicantecoli
  • 22156 Answers

SOURCE: rear wipers not working nissan almera 1.4 1998

try the wires in the rubber hose on top of the back tailgate

Posted on Oct 26, 2009

  • 70 Answers

SOURCE: Nissan r32 skyline front window wiper not working

Check if ther is power to the front wiper moter when its on if ther is power then replace the moter, if no power check wiring.

Posted on Apr 04, 2014

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find switch for rear wiper. Rear wiper not working. 99 nissan pathfinder.


Check it wireing to open dickky. I think any cut on wire you found. Other check fuse off wiper in fuse box care fully.

Jun 18, 2016 | 1999 Nissan Pathfinder

1 Answer

Have a 1997 nissan xe pickup trying to find out where the relay is located for the windshield wipers


Sorry, my wiring diagram doesn't show a relay. The washer motor and wiper motor use the same fuse in fuse block, fuse seven--20 amp. Of course if the washer motor works ok, the fuse isn't the problem.
The wiper switch is part of ground circuit for motor, if that helps you any.

Mar 11, 2016 | Nissan Cars & Trucks

1 Answer

Which is the fuse for windscreen washer in a 2010 yaris car ?


The fuse box is located down or just above where a driver puts their left foot, under the steering well and below the coin box. According to ABMforum.com: "The front wiper rear wiper and washers are on separate fuses (15A WSH front and rear washers 25A WIP front wiper 15A RR WIP rear wiper)."

May 15, 2015 | 2010 Toyota Yaris

1 Answer

Rear window washer not working


is there water in rear bottle?

Nov 14, 2012 | 1997 Nissan Quest

1 Answer

Ford Expidition 2001, rear wiper is not working, water sprays but no action


The washer and wiper are two separate circuits. At the central junction box check 15A fuse 14 which feeds the battery saver relay. At the battery junction box, check fuse 12 which feeds the rear wiper down and up relays. Rear wiper action is controlled by the generic electronic module (GEM). If the rear wiper switch is set to one of the intermittent positions, the battery saver relay closes to apply power to the wiper down and up relays. The GEM selects high/low or park operation. Note that there is an internal thermal breaker in the rear wiper motor so if everything else checks out, the motor may have overheated and opened that fuse. also, the rear wiper relay(s) could be defective

Sep 28, 2012 | 2001 Ford Expedition

1 Answer

Rear window wiper not working


could be a few things so here goes
rear window wiper relay rear window wiper fuse motor or the connections are loose or rusted get these checked first hope this helps ivan

Sep 26, 2012 | Nissan Cars & Trucks

1 Answer

To replace rear wiper blade on nissan note 2010


Read the manual for my 2010 Note and it says to remove the old one simply rotate the wiper blade anti-clockwise until it comes free. I've done this and it feels like you're going to break it but it just comes free! then to fit the new one simply reverse the rotation. Simples.

Apr 06, 2012 | 2010 Nissan Note 1.6

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...