Question about Dodge Cars & Trucks

1 Answer

Have a 01 dodge caravan se 3.3 there is no power going to the eatx transmission relay van is in limp mode tryed to use test light to get the relay to open notting any help thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Dodge Master
  • 521 Answers

On the drivers side of the van in the front of the drivers side wheel and behind the front bumper is a module and wiring you should check.pull slightly on every wire and you should find broken /corroded wires that need a repair.
Next location for trouble is under the fuse box in the engine compartment.

Posted on May 19, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the van have to have a EATX shutdown relay?


If you mean the electronically controlled transmission which I assume you do, the answer is no such relay..

May 09, 2016 | 2000 Dodge Caravan

2 Answers

What is an eatx shutdown relay and eatx backup relay


There is an (auto shut down relay) located on the van in the fuse/relay panel under the hood. It controls the fire to the coil,fuel injectors alternator. (never ever heard of a (eatx relay)??? Or a (eatx backup relay)??? Hope this will help you.

May 15, 2010 | 1996 Dodge Caravan

3 Answers

What is an EATX shutdown relay and eatx backup relay


eatx stands for electronic automatic transmission controller
the eatx relay provides power for the controller and the backup eatx relay is for the backup lights

Mar 30, 2010 | 1996 Dodge Caravan

1 Answer

My 2.4 caravan is not shiffing to 3and 4 geer and the oil light keeps coming on i alread ghanged the oil two times.the van runs grate if I dont go over 40.


your transmission is in "limp mode"
it will not up shift because there is a problem with one of three sensors,
1=input sensor
2=output sensor
3=speed sensor
the computer won't let the transmission up shift because it doesn't know how fast you are going ,

Dec 28, 2009 | 1998 Dodge Caravan

2 Answers

P0700, P0750 and P0755 codes I was driving at 65 mph and the 2003 Dodge Caravan down shifter to low gear and the check engine light came on. It will not ship to high gear.


P0700 (M)
Check Transmission DTC's
This code indicates that the EATX (Transmission controller) has an active fault and has illuminated the MIL via a BUS message. The specific fault must be acquired from the EATX via a DRBIII tool. (Input or Output Speed Sensor failures often cause this code and are a common failure part on WJ Grand Cherokees

P0750
Shift Solenoid circuit.
Note: If code P1767 (Transmission Relay Always On) is also present: Replace transmission solenoid assembly. See note provided. When transmission is in limp mode the relay that provides power to the solenoid group is switched off. This is normal and is designed to provide operation in one gear only. Engineering department suggests to replace transmission solenoid assembly anytime these two trouble codes occur together. See applicable service manual section (21) for solenoid assembly replacement directions. IMPORTANT: When performing this repair always check torque on all valvebody accumulator cover plate screws. Proper torque specification is 70 inch pounds. If any accumulator cover plate screws are damaged or missing replace the valvebody assembly. NOTE: If any other trouble codes are present do not replace solenoid assembly. See test in the applicable Transmission Diagnostic Procedures Manual

P0755
Shift Solenoid B

Oct 14, 2009 | 2003 Dodge Caravan

1 Answer

I have a 98 plymouth grand voyager with a 3.3l 4 speed transmission. My van goes into limp mode after a couple minutes of driving. My question is how do I determine if my shift solenoid or my tcm is the...


THERE MUST BE SOME FAULT CODES STORED IN TCM..WHEN A FAULT OCCURS,THE TCM SHUTS THE POWER FEED OFF TO THE SHIFT SOLENOIDS IN THE SOLENOID PACK SO ALL YOU HAVE IS SECOND GEAR(LIMP MODE)..IS YOUR SPEEDOMETER WORKING?IF NOT IT MAY BE THE OUTPUT SPEED SENSOR IS BAD..YOU SHOULD GET TCM SCANNED FOR FAULT CODES..I HOPE THIS HELPS

Sep 17, 2009 | 1998 Plymouth Grand Voyager

4 Answers

98 Plymouth Voyager Transmission won't go or stay in drive


I got the exact same problem as mike d ready.
i have replaced the 2 tranny sensors over the years. yjey can cause the same symptoms. but the sensor problems came on all at once.
bad shops tell many dodge van owners irs te tranny and its really just the sensers.

Jan 06, 2009 | 1998 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...