Question about Cars & Trucks

1 Answer

How much the valve clearances corroborate avanza 1.3 cc

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 923 Answers

  1. Could you re-word your question? It makes no sense to me the way it is now!

Posted on May 11, 2017

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
alicantecoli
  • 22219 Answers

SOURCE: i want to know how

general rule of thumb on most modern engines except high compression GT engines from the 60s is 12th inlet and 15 exhaust ,nearly all modern engines from the late 70s onwards use this average setting so you cannot go wrong on manual adjustment tappets

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Nissan extral head valve inlet tight how does


Valve clearance on NISSAN E15 (S) Engine - Nissan Forum

www.nissanforums.com/.../49192-valve-clearance-nissan-e15-s-engine.h...

Mar 3, 2004 - 15 posts - ‎6 authors
Does anybody know what is the valve clearance for inlet and outlet for this type of engine? ... Nissan Xterra Forum · Nissan Armada Forum · Nissan Frontier Forum ·Nissan Titan Forum ..... the head so they don't burn up, especially the exhaust valves.Tight exhaust valves are the #1 reason they burn up.

Nov 28, 2015 | Nissan Cars & Trucks

1 Answer

What is the valve clearance of isuzu 4ba1?


The 4BA1 is a 2.8 L (2,775 cc) diesel sold in Isuzu Elf light trucks of several generations
what year, and in what car? or truck?
this is a USA forum and we dont have elfs, here, im guessing elf.
did you goggle first.?
here ill do that for you.
https://www.google.com/webhp?gws_rd=ssl#q=++isuzu+4ba1+valve+clearance

see all those hits, read em?

May 17, 2015 | Isuzu Cars & Trucks

1 Answer

Whats the valve clearance for my Diahatsu Mira 1998 850cc?


Mira 847 cc 1993- Engine Code ED 10
Ignition data
  • Ignition system type: El-ecu
  • Ignition coil make/type: Dia/-
  • Supply voltage: 12 + Volts with ballast resistor
  • Primary resistance: 1.35-1.65 Ohms
  • Secondary resistance: 22000-30000 Ohms
  • Distributor make/type: Den/-
  • Contact breaker gap/air: 0.2-0.4 mm
  • Dwell angle: Deg\par Ignition Timing - unleaded: 5 2/900 Deg eng/rpm (without vacuum)
  • Ignition Timing - leaded: Deg eng/rpm (without vacuum)
  • Timing mark location: Flywheel
  • No 1 plug location: Pulley
  • Firing Order: 1-2-3
  • Spark plug make: Bosch
  • Spark plug type: WR6DC
  • Electrode gap: 0.7-0.8 mm
Fuel System
  • Fuel type: U/L
  • Fuel pump type/pressure: bar
  • Engine idle speed: 900+100/-50 rpm
  • Fast idle speed: 2000 rpm
  • CO level at idle speed: 1.0
  • 0.5 Vol %
Engine Data
  • Valve clearance - inlet: 0.25 mm (hot)
  • Valve clearance - exhaust: 0.30 (hot)
  • Compression pressure: 1.2-1.5 bar
  • Oil pressure: 2.5-5.6/3000 bar/eng/rpm
  • Radiator pressure cap: 0.6-1.05 bar/type
  • Drive belt 1 - size: 9.5x925/KDB 925 mm/type
  • Drive belt 2 - size: mm/type
Electrical System
  • Alternator output: 10/2500 Amps/eng/rpm
  • Regulated output: 14.2-14.8 Volts
  • Battery: 12/35 V/Ah
  • Starter motor make/type: Den/-
Other data
  • Clutch operation type: Cable
  • Clutch adjustment: 10-30 mm
  • Cambelt failure: Damage
  • Cambelt Part Number: 13514-87211
  • Tyre pressures: 1.8(26)f 1.8(26)r bar (psi)
  • it took me 3 seconds to google this then i realized that this is a older engine then yours

Oct 30, 2014 | 1996 Daihatsu Mira

1 Answer

1.3 valve clearance suzuki


1995 samurai. valve lash , right not valve stem to guide clearance.
there are 3 clearances.
http://www.fixkick.com/sammi-stuff/index.html
volume 1
pdf page 111 tells you this (book page C3-53)
the manual is everywhere.

Jan 21, 2014 | 1995 Suzuki Samurai

1 Answer

Where is the thermostat located in toyota avanza cooling system


In the evaporator coils. It's a small diameter tube that goes to the top of the expansion valve.

Mar 10, 2013 | 2007 Toyota Avanza 1.3

2 Answers

I have problem with my engine 4K toyota. It heard an engine noise during idling, for my little knowledge in engine repair, can you give me any procedure mannuals in adjusting engine valves for my...


Valve Clearance Valve clearance is there to allow the valves to cool in between combustion events (spark), and to make sure the valve closes properly and contains the combustion explosion. You need to cool the valves a little bit, the exhaust valve moreso than the inlet, as it's what sees the most heat as spent burnt gases go past it into the exhaust port. Run too little clearance and you'll cause the valve to "weld" a little bit to its' seat every time it closes, and then take seat metal off again when it opens. Do this enough times and you burn out the valve seat and need the head reconditioned. However, by running less clearance, the valve stays open for that little but longer, and you get more air in and out of the motor, and make more power. Run too much clearance and your motor just sounds like a diesel and loses power and tappet rattle annoys you while you're driving, so it's better to err on the side of caution.
The stock valve clearance (0.008" inlet / 0.012" exhaust, warm) is pretty good for any of the cams I've listed above, they're well-sized street cams, not really wild top heavy race cams that require super high compression to work, so don't be afraid to close the valves up a bit from the suggestions of the cam grinder, which will usually say between 0.010" and 0.014". There are a few ways to set your valve clearances:
Yellow Book Method This is from the factory 3K/4K/5K engine manual, aka The Yellow Books. It's the quick and lazy method.
Set engine to #1 TDC. Crank pulley timing mark should be on 0, distributor rotor should be pointing towards spark plug 1 or 2. Set tappets (counting from the front) 1, 2, 3 and 5. Rotate engine 360 degrees, crank pulley to 0 again, distributor rotor turned 180 degrees. Set tappets 4, 6, 7 and 8.
Nine Method I've never really gotten into doing this, takes too much time and maths for my liking :P Rotate the engine through its' range of movement, as one valve is "on the rock" of its' max lift, subtract the valve number from 9 and that's the tappet you should be setting. For example, if #8 valve is open, set clearance on valve #1. If valve #7 is open, set clearance on #2. And so on.
Stewart uses this method, and rotates the camshaft through its entire base circle and sets the clearance at the highest point. Which is a pretty good idea, as it compensates for the possibility that the base circle has been ground unevenly, and allows you to run the proper valve clearance that you want to run, instead of something that may be a few thou larger in reality.

Feb 10, 2011 | Toyota Corolla Cars & Trucks

1 Answer

Carburator and valve clearances


For the carb :
Idle r/min.- 1550+_50 r/min.
fuel level- 4.5+_5.0 mm
float height- 25.8+_1.0mm
pilot screw- 1-3/4 turns out
do you need jet #'s or not?

the "+_" signs are those plus-over-minus signs i cant do on my comp.

Valves:
valve diameter- in-30mm
ex-26mm

valve lift- in-5.5mm
ex-5.5mm

valve clearance or tappet clearance (cold):
in & ex: .08-.13mm

valve guide to valve stem clearance:
in-.010-.037mm
ex-.03-.057mm

valve guide I.D.: in & ex-5.5-5.512mm

valve stem O.D.:in-5.475-5.490mm
ex-5.455-5.470mm


Hope this helps.

Jan 30, 2011 | Suzuki Swift Cars & Trucks

1 Answer

How do i adjust the valves in a ford 1997tarus with a 3.0 ohv


Valve Stem to Guide Clearance · Intake
0.026-0.071 mm (0.001-0.0028 in) · Exhaust
0.038-0.083 mm (0.0015-0.0033 in) Valve Clearance
  1. With No. 1 piston (6108) on top dead center (TDC) at the end of compression stroke (Position No. 1 in the illustration), check the following valves:
    Position 1
    No. 1 exhaust valve (6505) No. 1 intake valve (6507).
    No. 3 exhaust valve No. 2 intake valve.
    No. 6 exhaust valve No. 4 intake valve.
  1. Rotate crankshaft (6303) 360 degrees to position No. 2 and check the following valves:
    Position 2
    No. 2 exhaust valve No. 3 intake valve.
    No. 4 exhaust valve No. 5 intake valve.
    No. 5 exhaust valve No. 6 intake valve. 4cb038f.gif

Oct 19, 2009 | 1997 Ford Taurus

1 Answer

Specs for a 1997 Ford Ka 1297 cc


If the vehicle is fitted with a Rocam engine, the valve clearance is not adjustable, hydraulic lifters.
The camshaft caps are torqued in two stages, first 10Nm and than 90 degrees

Apr 10, 2009 | Ford Focus Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...