Question about Cars & Trucks

1 Answer

I need to order an easy pass - Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 12,650 Answers

Go to ezpass site and follow instructions or go to a regional office and apply

Posted on May 10, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

We left florida and realized we forget are easy pass at home we are traveling and need are pass why can we do

call at the nearest place that sell the pass and keep travelling or get one on line

Jun 28, 2017 | Cars & Trucks

1 Answer

How to buy a easy-pass in TEXAS

Why pay to pay? You can order one from Dallas and it is free. Through an agreement, you can use the one from Dallas on all of the toll roads. I will post a link that will let you order one online and you can read the concept behind it as well.
How to get EZ Tag for tollways free

Now if you can't stand not paying anything to get a toll tag... you can go to the second link and pay for it.

Semper Fi,

May 09, 2017 | Cars & Trucks

2 Answers

How to determine the resistance needs to bypass the TDM and passlock on my 04 Chevy Impala

You can't
The Passlock?"¢ sensor contains 2 hall effect sensors. The tamper hall effect sensor is on the top. The security hall effect sensor is under the tamper hall effect sensor. Both of the hall effect sensors monitor the magnet of the lock cylinder through an opening. The tamper hall effect sensor is physically placed on top of the security hall effect sensor. This arrangement enables the tamper hall effect sensor to engage first if an intruder attempts to bypass the Passlock?"¢ sensor by placing a large magnet around that area of the steering column. There is a tamper resistor inside the Passlock?"¢ sensor in order to help prevent tamper to the system. Passlock?"¢ equipped vehicles have a selection of 10 different security resistors ranging from 0.5K ohms up to 13.6K ohms. Installing one of the security resistors inside the Passlock?"¢ sensor will generate a unique Passlock?"¢ code. All 10 combinations of the Passlock?"¢ sensor have the same part number.
Ignition lock cylinder has a connector with three wires marked A-B-C , A is a yellow wire - signal to the BCM .

Jun 01, 2015 | 2004 Chevrolet Impala

1 Answer

How do you by-pass a nuetral safety switch on a 1996 ford mustang

why by pass it they are easy to fix. it could just need adjusted. most are located on the steering colume.

Apr 11, 2014 | Cars & Trucks

1 Answer

Po719 can this code be due to an overfillig of tranny fluid?

Hi Noah,The code says your brake light switch input is week,here's a guide on how to replace.Here's the part.If you have to order,it will arrive the next day,easy fix.

Mar 20, 2013 | 1996 Chevrolet Blazer

1 Answer

How to remove heater core

Under the pass dashboard is a black plastic cover. remove screws and all attaching hardware. Make sure you have drained the antifreeze before removing the core. remove the hoses from the two tube under the hood leading to the core. back under the dash, remove the support brackets holding in the core. it should slide out. install in reverse order. sounds easy, but can be a headache sometimes. good luck

Mar 28, 2012 | Cars & Trucks

2 Answers

I am not sure I detected anything until I sent my car to the dealer for State inspections services and the mechanic told me I needed rear wheel bearings which would cost me a whopping $640! in order to...

the maximum wheel bearing end play is .040in so if there is to much end play that is why you failed the inspection. you can replace them yourself with just some basic hand tools it is not easy ( if it were easy everyone would do it ) but it is do-able. the bearings cost $184.52 ( retail ) at NAPA ( part # PBR 930362 ) if you think you want to try it yourself let me know and i can get you the procedure and torke spec.

Jan 29, 2011 | 2003 Nissan Altima

1 Answer

Spark plug diagram on a 1996 blazer?

V-8=pass side cyl.2-4-6-8....drivers side cyl. 1-3-5-7....firing order 1-8-4-3-6-5-7-2....v-6= pass side 2-4-6...drivers side...1--3-5 firing order listed on top if its a flat dist cap....if round cap order is 1-2-3-4-5-6-5...good luck..Lee.

Sep 14, 2009 | 1996 Chevrolet Blazer

2 Answers

What is the fireing order for a 1995 chevrolet camaro 3.4 liter v6?

123456. odd numbers on drivers side even on pass side 1 is driver front of engine 2 pass side front of engine.
in order front to back drivers 135 same for pass side 246 front to back.

May 03, 2009 | 1995 Chevrolet Camaro

2 Answers

Firing order for 1989 full size ford bronco 302

13726548 #1 cyl is front pass side and count to back 1234 are on pass side.5678 are on driver side.# 5 being front

Apr 22, 2009 | 1989 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides