Question about Kia Forte

Open Question

Need exact location of bolts that must be removed in 60/40 rear seat of kia forte, in order to remove back seat.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 2000 blazer power seat

The guy that posted the first solution...that works...My power seat module went bad , so I used a 12 volt batery charger on the wires to move my power seats.

Posted on Mar 21, 2009

  • 185 Answers

SOURCE: remove rear seat lexus es300 2008

the bottom of the rear seat pulls straight up at the front and out. its pretty tight, you need to pull very firmly.

Posted on Oct 20, 2009

  • 1 Answer

SOURCE: 1999 Chrysler Concorde LXI Rear Speaker replacement

If you mean the rear shelf removal, then you begin by removing the rear seat (lift to release the corner clips on each side holding the cushion to the floor). Then remove the fasteners for the seat belts, then lift the seat back to raise and release it from its clips, and remove it from the vehicle. There are then a lower and upper trim panel around the back shelf that you need to remove (these may be on each side of the shelf, e.g. they are called 'quarter trim' panels). Then you will see some push-pin fasteners that hold the shelf across the front lower edge, so you gently pry out the center push-pin of each one of those to release the fastener. Then you pull the shelf forward to release it from the clips that hold it under the window. Then remove the wire to the center high-mounted brake light. The panel with its speakers attached can then be removed, but also remove the wires from the speakers so you don't break those. connections.
That is the procedure as shown in my '98 manual.

Posted on Apr 13, 2010

  • 14036 Answers

SOURCE: how to remove bottom of

PUSH IN CENTER FRONT EDGE CUSHION TO DISENGAGE PART OF SEATS WIRE FRAME FROM CLIPS.WITH CLIPS UNHOOKED LIFT UP AND REMOVE SEAT.IF REAR SEAT NOT HELD IN PLACE WITH CLIPS. LIFT UP THE REAR SEAT CUSHION AND PIVOT IT FORWARD. DETACH THE RETAINING BOLTS AT THE LOWER EDGE OF THE SEAT BACK AND IF NECESSARY REMOVE THE SEAT BELT ANCHOR BOLTS.LIFT UP ON SEAT BACK REMOVE IT..

Posted on Feb 06, 2011

  • 202 Answers

SOURCE: how can i remove rear seats from my 2011 Vauxhall Insignia, also replace offside rear seat belt as I have had a mouse bite through the belt and the back seat

shoot the mouse !!!! ,,,, sorry coldnt resist ,,, you have to lift rear seatbase and boot carpet to get at the seat back bolts ,,, not a big problem ,,, the big one is getting at the seat belt because u have to remove alot of trim to get at the seat belt bolts ,,, alot of clips are involved that will break so source new clips before you start the job ,,,,rotten job so feel so sorry for you ,,,,

Posted on Dec 07, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do u remove the rear seat on 1196 honda accord?


The rear seat is four (4) pieces.
You will need two tools a 6mm and 8mm wrenches.
1.) Unbuckle the rear seat belts. 2.) Locate the bolt in the center part of the rear seat, between the cushion and the seat-back. Remove the bolt with a 6 mm socket wrench. 3.) Push down firmly on the front edge of the rear seat cushion and pull it toward you to unhook and remove the rear seat cushion. Push the seat belt stalks through the center holes and lift the cushion out of the Accord. 4.) Pull the lever on the side of the rear seat bolster to lower the rear seat-back, which must be in the down position to access its bolts. 5.) Slide the center seat belt toward the passenger side of the vehicle. Move the loop over the edge of the seat-back to prevent it from hindering removal. 6.) Remove the three bolts from the bottom edge of the rear seat-back, using an 8 mm socket wrench. One bolt is in the center; the other two bolts are on either side. 7.) Pull the rear seat-back out of the Accord. The remaining sections of the seat should be the two side bolsters. 8.) Remove the bolts from the bottom of the side bolsters with a 6 mm socket wrench. Push firmly against the first side bolster. Push it upward to slide it out of its mount. Repeat the process on the bolster on the other side to finish removing the Accord's rear seat.

This should take approximately 15-30 minutes depending hoe mechanically inclined a person is.

Sep 17, 2014 | 1996 Honda Accord

2 Answers

How do I Remove front passenger seat kia forte


There are bolts on the track that the seat adjustment goes to and they are in the floorpan remove those and you should be able to remove seat

May 04, 2014 | 1998 Ford Escort

2 Answers

Where is the expansion valve located on the 2004 KIA Sedona


Kia Sedona expansion FRONT valve located under dash, behind glove box, fan and coil. Evacuate freon first. Disconnect Freon lines from firewall., Lay right front seat back to flat horizontal position and lay on top or totally remove the seat for easier working access. Remove under dash cover, fan, glove box, coil housing, remove coil mounting bolts, remove old expansion valve. (Inspect old valve, if debris inside, blow out coil before installing new valve. If visible debris best to consider replacing REAR expansion valve and DRIER/FILTER in front of radiator too and blow out all lines and coils while servicing.) Use compressor oil to lubricate "O" rings on new FRONT or REAR expansion valve, install valve bolts, reinstall coil bolts to FRONT firewall or REAR frame, reconnect freon lines to firewall in engine compartment. Evacuate AC system, install freon (35 1/2 ounces, nominal 3 pounds), check system for leaks, check for proper operation, enjoy.

Sep 12, 2012 | 2004 Kia Sedona

1 Answer

Remove rear seat kia09 optima


There are two bolts located at the bottom part of the rear seats in the front just behind the driver seat and passenger seat, once those bolts are removed you will be able to lift up and out

Sep 11, 2011 | 2008 Kia Optima

1 Answer

I need to remove the rear seat in my Kia so I can get my scooter into the back of the KIA.


I removed the backseat of my 2000 kia Sportage so my Labrador could have enough room to move around when we travel. Its easy to do (I'm a girl w/little mechanical experience) so you can do it easily. The bolts are easy to find in the front of the seat and the back. Just unbolt and take out the seat.

Mar 15, 2010 | Kia Sportage Cars & Trucks

1 Answer

Is there a rear seat release on a 94 accord


I believe this procedure applies to your 94 Accord:
With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Lift the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Dec 21, 2009 | 1994 Honda Accord

1 Answer

Remove backseat of honda accord 1991


With your hands, press down on the seat cushion where it meets the seat back. Locate the retaining bolt(s). Some models retain the seat with one bolt in the center; others use two, evenly spaced left and right.
Remove the retaining bolt(s).
Life the back (toward the rear of the car) of the seat bottom upwards while rotating it toward the front of the car.
Disconnect the hooks at the front edge (during the rolling motion) of the seat and remove the seat bottom.
Remove the carpet (in the luggage compartment) from the rear of the seat backs.
Remove the seat back mounting bolts from the luggage compartment side.
Lift out the seat back.
If the rear side bolsters or pads are to be removed, remove the lower mounting bolt, then push upward to free the hooks.
Hope this helps you.

Oct 17, 2009 | 1991 Honda Accord

2 Answers

I need to replace the rear struts and spings on my 01 sable, Where are the top nuts to loosen for the struts


The bolts are located under the rear deck (where the rear speakers are located) inside the car. First start by opening the fold down rear seats. There you will find 4 bolts holding the rear seat back. Remove them. Pull the seat back forward and lay it down on the rear seat. Next remove the rear deck. There are 2 plastic push-in clips that hold the rear deck. They located toward the front. Pull them out. Now the rear deck can be removed by sliding forward towards the front of the car. Under the rear deck is insulation which can be lifted out. Under the insulation are the bolts for each strut. Remove these bolts and the strut can be pulled out.

Aug 14, 2009 | 2001 Mercury Sable

1 Answer

How to remove interior back dash on 2006 hyundai sonata


The shop manual does not illustrate the procedure for removing the rear package deck (back dash). This will be a lengthy description for removing this deck
1. Remove the rear seat bottom (2 12mm bolts located in between the seams at the seat back and the seat bottom (lower the seat backs and you'll have to feel for them). Remove them
2. Remove the seat bottom (two spring loaded clips at the front of the seat bottom).
3. Remove the 12 mm bolts at the bottom of both LH & RH shoulder cushions. Lift UP and then forward (careful you don't break the should cushion clips at the back of the cushions).
4. Using a small screwdriver, remove the SRS caps at the C-Pillar moldings (behind them are either two phillips head screws or 10mm bolts) - remove them
5. Remove the C-Pillar moldings -- they are 'Clipped' into position (use a flashlight to locate them and a long shaft plane screwdriver to help 'unclip' them).

ff32eaf.jpg lower the seat backs down. Note the trunk accessway side moldings (approximately 8 to 10 phillips head screws) remove them and the accessway moldings (you can'r remove the deck unless you remove these accessway moldings).
6. Find the plastic clips which hold the rear deck in place (usually yellow or blue)


0fbe0c6.jpg Remove the rear package deck.
Now, depending on what you want to do now... it's up to you.
Reassembly is in reverse order.

Jun 19, 2009 | 2006 Hyundai Sonata

1 Answer

How to remove rear seats from a kia optima 2006.5


There are two bolts located at the bottom part of the rear seats in the front just behind the driver seat and passenger seat, once those bolts are removed you will be able to lift up and out

Feb 09, 2009 | 2007 Kia Optima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...