Question about Jeep Cars & Trucks

1 Answer

2003 jeep wrangler 2.4 no spark on 2 of the 4 cyls

Also car will run on 2 remaining cyls no ck engine lt on no codes stored

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Jeep Master
  • 1,062 Answers

Possible coil pack (if it has a pack)

Posted on May 10, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 jeepn wrangler 4 cyl 5 speed rough idle


rough idle is from faulty injectors or maf/vaf sensors or vacuum leaks
run the fault codes to determine the fault area

Jun 09, 2014 | 1999 Jeep Wrangler

1 Answer

Sport Wrangler 6 cyl. Engine lite flashing. Diagnostic tool lists code PO305. I looked it up and it states misfire in cyl #3 & 5. How do I fix this?


Check the plugs, wires and coil pack for these two cylinders. Most lilkely it is the coil pack, they work for 2 cyclinders at a time. cylinder motors use 3 and 8 cyl moters use 4 of these. If your und=sure where the coil pack is, follow it backwards from the spark plugs.

Jul 08, 2011 | 2002 Jeep Wrangler

1 Answer

Whats the oil capacity for a 2003 jeep liberty?


2003 JEEP LIBERTY 2.4L 4-cyl Engine Code [
Engine Oil Grade 1....API* SAE 5W-30 is preferred.
CAPACITIES:
Engine, with filter..........4.7 liters

2003 JEEP LIBERTY 3.7L 6-cyl Engine Code

Engine Oil Grade 1......API* SAE 5W-30 is preferred.

CAPACITIES:
Engine, with filter..........4.7 liters

Thank you for using fixya and good luck

May 31, 2010 | 2003 Jeep Liberty

1 Answer

1994 jeep wrangler 6 cyl 5 spd no start


have u ck out the ignition switch [not the key & tumblers],, or the neutral safety switch to see if u have power ,,also seen broken wire at solenoid on starter too,,hope it helped,,

Apr 05, 2010 | 1994 Jeep Wrangler

1 Answer

Getting code P1022 when checking onboard diag. chek engine light also on intermitt 03 jeep wrangler 6 cyl 4X4


that is an injector problem.injector # 2 is letting out a high output.this could be there is a bad connector or a damaged wire.this will affect the way your injector reacts and will cause the check engine to go on and off.you would need an injector tester to check the spray pattern for your injector.

Oct 04, 2009 | 2003 Jeep Wrangler

1 Answer

No spark from ignition module on hot start


95 JEEP WRANGLER 4 CYL

No spark. I have changed out the distributor cap, rotor, wiring from coil to cap, and coil was replaced. I checked the distibutor by turning ignition key and observing the rotor turn. What else can I check. I did not observe a module.

Jun 19, 2009 | 1995 Jeep Wrangler

2 Answers

Check Engine Light illuminated


The most likely problem is the crank sensor , as far as check eng light find out what code it is that might help. Codes on little code readers are sometimes just a general discripition that could even lead you in the wrong direction. most of the time the fuel system does not trip the light. so rule that out for your question, not to many sensors will stop the motor that leaves the crank sensor which is a jeep night mare they always go out. it will be located in the top of the bell housing where the eng and trans go together. on the 6 cyl you can most of the time lean over the engine and see it. it will have one small bolt holding it in and then the little wire harness to unplug.

Jun 14, 2009 | 2003 Jeep Wrangler

2 Answers

97 wrangler 6 cyl ck eng lite just came on light


first you need to find out the code auto zone or advance auto should give you a code reading , i try to help but without the trouble code im lost

Dec 19, 2008 | 1997 Jeep Wrangler

2 Answers

My 2002 jeep wrangler sport 4 cyl engine lite stays on dashboard,it does not affect performance.


Have you taken it to your mechanic to run the diagnostics... I had the same issue and it turned out to be a vapor lock issue that required a gas tank gasket replaced.

Jul 31, 2008 | 2002 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...