Question about Cars & Trucks

1 Answer

I'm looking for a frt diff for my 214 4x4 serial# 14BT4059/347605/7. I would also need both axle bearings and seals. I do have a few part numbers but none for the rotating assembly. Thanks Keith

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 43,127 Answers

Try a dealer or a parts supplier . we have no information here on parts for unknown vehicles

Posted on May 10, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

BigBlue77
  • 59 Answers

SOURCE: 2005 Yukon Front Diff Axle seals

You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Posted on Sep 06, 2008

  • 1118 Answers

SOURCE: 85 cj7 rear axle removal

Do you have bolt in axels? or are they held in with C- clips? If its bolt in axels you need to remove the bolts, and you may need an axel puller to get them out. If its got C- clips rear cover on rearend has to come off, and pin has to be removed to get C- clip out to get axel out.

Posted on Apr 03, 2009

  • 245 Answers

SOURCE: i need to replace the left side drive bearing and axle seal in a 4t60e trnny. can it be done with the tranny still in the car?

the axle seal yes. the drive bearing? are you talking the one inside the trans or the cv joints or the outer wheel bearing the bearings inside the tranny cannot be replaced without pulling the trans out.the others can be.

Posted on May 20, 2009

roniecon
  • 6826 Answers

SOURCE: Replaced rear axle pinion bearing and seal, need

There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Posted on Apr 19, 2010

  • 5370 Answers

SOURCE: need to replace rear wheel

It requires a special tool to remove and refit the bearing from hub assembly.Also if its not coming out ,then in some cases the hub has to be replaced. The new hub comes with bearings. Click this link directly to see the exploded diagram and procedure to remove and replace parts in 2003 Toyota highlander:-- http://technoanswers.blogspot.com/2011/02/2003-toyota-highlander-rear-wheel.html -------------- Check out.Keep updated.Thanks.Helpmech.

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a 1998 P38 Range Rover and the rear diff tends to lock up when doing tight turns. Can the limited lip be adjusted ?


yes
but it is for a professional transmission shop to do the adjustment
problems as stated start from the wrong oil being used in the differential
have a diff oil change done , flush out the diff the put the correct limited slip diff oil back in
it is not standard diff oil but special oil

Jan 13, 2017 | Rover Cars & Trucks

1 Answer

1992 f150 front axle to diff. seal replacement


OK, you must remove the front axle assembly to access the axle flange and then the seal, follow the instructions at the link but once the axle is out remove the axle flange from the front diff and replace the axle seal, use a seal driver and lube the new seal with lithium grease (white grease). You will need an air impact to get the flange nut off, replace it with a new one (do not reuse) and do not over tighten it. Cinch it down and then go about 1/8 more of full nut rotation to preload carrier bearing setting then spike in place. Ford F150 Front Axle Replacement Part 1

May 19, 2016 | Ford F-150 Cars & Trucks

1 Answer

Replace rear wheel seal


remove the rear axle and the seal will be in the end of the axle housing. Pull it out -fit the new seal in the same way and refit the axle. For seals to leak it is an indication that the bearing is either shot or needs adjustment so check that out as well. Check that the diff bleeder at the top of the diff is clear and that the diff is not over full

Aug 03, 2014 | 1996 Pontiac Firebird

1 Answer

1984 Chevrolet Custom Deluxe rear hub service


If you can see inside the wheel bearings then they require lubrication from the differential. If they are sealed then no. You don't say if the rear axles are 1/2 ton or 3/4 ton. No brand of seal will seal better than any other. Spray engine degreaser in the rear end and flush out with water. You may need to do that more than once.

Mar 30, 2013 | 1984 Chevrolet C1500

1 Answer

I have a 1999 Mercury Grand Marquis. i noticed a little diff fluid coming from the right rear wheel. I changed the wheel seal and axle bearing and put it all back together and filled the rear diff with...


first swap to a front tyre to eliminate that issue


new bearing shouldn't be rumbling
to get the bearing square on and home
did you use a press to fit the bearing to the rear axle
or tube method ?

and did the seal kit have this nifty plastic seal fitter so axle didn;t rip the seal surface

index-iamfpwhpnyqdk3sl3340sktr-1-0.jpg

Apr 12, 2017 | 1999 Mercury Grand Marquis

2 Answers

Front diff leaking driverside right at cv joint makes a humming noise.diff bearing or seal or possible wheel bearing ?


Sounds like a hub bearing a nd a leaking axle seal to me. The two parts are seperate and have nothing to do with the other so it was just a coincidence that you noticed the leak after you heard the hub bearing. Replace the axle seal to stop the leak and then replace the hub bearing assembly to fix the humm because you have to dissassemble all of that to fix the axle leak anyway.

Jul 31, 2011 | 1999 GMC Jimmy

1 Answer

How to Replace rear wheel bearing


first remothe the diff cover and drain, find the bolt that retains diff gears and remove then remove pin holding the diff gears, at this point do not rotate any part at all, axle or crown, push axle inward and remove c clip holdin axle in, pull axle out and using a bearing puller remove bearing, lubricate new bearing and install using new seal, examine axle for damage to bearing contact surface is good install , reverse procedure to finnish and fill rear end with new oil

Sep 16, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

Jeep cherokee diff


Yes,it is a self contained bearing and seal together,that is off set,the bearing runs on a different part of the axle,and the seal,this way there is no leak,and the bearing rides on a smooth part of the axle,will save money,napa has the part real cheap too,ask for a pgb bearing,it is a power glide brand,I think it is like 15.00 dollars or less

Jun 05, 2010 | 1998 Jeep Cherokee

2 Answers

Oil leak by back brake right side coming from axle seal need to replace seal donot no how to remove axle seal


Step 1, DO NOT follow the advice in Soultion #1.
You have to remove the axles to get to the bearing. If it's a C-Clip Dana 35C differential, remove the wheels and brake calipers and the 4 bolts holding the brake backing plate to the axle tube,remove the diff cover, drain the fluid, pull the C-Clip and remove the axle with a slide hammer or with the brake rotor put back on the wheel studs backwards. Dana 35C diffs the wheels bearings will stay in the axel tubes, go to Auto Zone and rent a bearing remover. If its a Dana 35 diff, take the axle to a machine shop and have the bearing pressed off and a new seal installed the have the bearing pressed back on.

Jan 15, 2010 | 1999 Jeep Grand Cherokee

1 Answer

Rear seal and bearing leaking on passenger side.


Basic to get tire and hub off, remove rear diff cover remove bolt, remove clip, pull axle out, then heavy puller to pull bearing and seal. Ck axle for wear

Sep 16, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...