Question about Cars & Trucks

Open Question

How to replace rear wheel bearings on a 2009 Hyundia Tuscon

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: Rear wheel bearings on Hyundai Accent

no i do not believe they are press in there are held in by a seal try www.autozone.com to see if they have your car listed if they do you will be able to get a diagram showing you how they come a part.

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

  • 52 Answers

SOURCE: how to replace rear wheel bearing on s type jaguar v reg

pretty basic the same and any other wheel bearing. But you need a hydraulic press, if you dont have one of those then their is just no way that you will be able to do it.

If it is newer than an 05 you need to take it to the dealership, because they need to hook up their computer and electronically disengage the rear parking brakes by putting it into service mode.

Posted on May 11, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuel pump rolover switch located on 2006 hyundia tuscon


In the cargo area behind the interior panels. slamming the rear hatch when closing, can trip the switch. It will have a red button that has to be pressed to reset

Jun 02, 2017 | Cars & Trucks

1 Answer

Rear wheel bearings


This vehicle has non servicable bearings. These bearing/hub assemblies can last the life of the vehicle. If one becomes noisey/loose then replacement is necessary. There is no actual mileage replacement interval.

Jun 07, 2015 | 2009 Kia Spectra

1 Answer

Where is the oil filter on my 2005 2.0 crdi Hyundai tuscon


hyundia tuscon oil fillter located . left hand side. looking at it from frount.right at back round steel unit with an allenkey at the top. it as apaper insert filter/

Sep 14, 2013 | 2004 Hyundai Tucson

1 Answer

The rear wheel bearing is grinding very loudly on my 2005 Hyundai Tuscon. I would replace the bearings but I don;t have a bearing press, so I will probably just buy a used hub assy. Does the hub just...


It should come simply as bolt on ptinciple, you will need only the tools you needed to take it off. I think you will need yours retainig nut.

Dec 01, 2010 | 2005 Hyundai Tucson

1 Answer

Noises coming from th left frontwheel of my 2000 hyundia sonota could this be a hub and bearing noise


What kind of noises are you hearing? Most likely, you need to replace the brakes. It is very unusual for a 10 year old car to have wheel bearing problems, especially on the front wheels.

A squeal when you apply the brakes or a grinding/dragging noise while you are driving are signs that it is time to replace the brakes.

Jan 30, 2010 | 2000 Hyundai Sonata

1 Answer

How do I replace front wheel bearings on my Ford Focus?


its a hub style wheel bearing, you need a slide hammer to take the bearing off. also make sure you take the snap - ring off. there is a few different ways you can tackle this, depending on which side its on. I.E) Front or Rear.

Jan 04, 2010 | 2009 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...