Question about Audi Cars & Trucks

Open Question

I take of two camshafts on audi a4 2.0 but now I can see the timing marks

Posted by on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1071 Answers

SOURCE: timing marks for KIA camshaft sprokets

they point to 12 oclock

Posted on Aug 19, 2009

  • 1071 Answers

SOURCE: how do i set the timing for audi A6 2003

there are actually special tools the cam has no timing marks the tool only goes on one way and locks the cams in place and it is actually a long process but there is no way to do it without the cam lock

Posted on Aug 20, 2009

  • 6674 Answers

SOURCE: camshaft timing mark crankshaft timing mark

Belt covers need to be on. Timing mark on crankshaft (while on compression stroke) should line up with TDC mark on cover. then Camshaft mark, needs to line up by looking through access hole of cover, and align mark on cam sprocket with pointer on inside of belt cover.

Posted on Oct 22, 2009

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at!

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Camshaft shaft timing marks on a 2000 audi s4

you can make your own marks by using a tip ex or white marker .

is it a petrol

if yes then take the coil pack of the cylinder one and turn the engine till the spark plugs reaches to the very top. that's your engine timing mark..

Mar 04, 2016 | Audi Cars & Trucks

1 Answer

Timing marks for 1994 audi 2.8 v-6

the "timing marks" on audi"s are on the cam sprockets. large holes on the lobes of the camshaft gears are supposed to face each other when cylinder 3 is at TDC the crankshaft has an arrow that needs to be aligned as well. see pics for reference

Dec 28, 2013 | 1993 Audi 90

1 Answer

Audi a4 1.8 please help with the timing settings of the timing belt and how do you reset it in the correct order

Hmmm. This is not something that one wants to get wrong. This is an 'interference' engine, and valve timing gone bad will wreck valves/head.

There are timing marks on the crankshaft sheave and on the camshaft drive. (Basically, this is done with the engine at top dead center. I don't think the pictures are that good on this site - i'm not sure you could see if I copied and pasted - but crash around the internet and, depending how computer-ish you are, you will find A4 manuals that show these marks. (The official Audi 'manual' is called ETKA and is killer huge. There are some copies of Bentley manual sections kicking around. There is a copy or two of the Haynes manual...) While you are getting the manual parts that show the marks, you will also get a diagram that shows the crankshaft rotation.

Once you have the marks (and make sure and then make sure again, and then make sure a third time that you do) the 'tight' side of the belt is the one on which the crankshaft rotation 'pulls' the camshaft, and the 'tensioner' side of the belt is the one on which the rest of the belt heads back up to the camshaft. So you have the timing right when the marks are where they are supposed to be when the tight side of the belt is tight.
When you have it right, but only after you have it right, and you are sure, then pull the pin that releases the tensioner - and puts tension on that side of the timing belt. (It is possible to recover the tensioner and re-set the belt if you have pulled the pin too soon, but it is not fun).

Oct 23, 2013 | Audi A4 Cars & Trucks

1 Answer

Need 2000 Audi A8 4.2 engine timing belt marks

There are no alignment marks on the camshafts, you must use the camshaft holder tool T40005 in conjunction with the crankshaft holder tool 3242 to properly align the camshaft and crankshaft

CAUTION: Incorrect removal or installation of the timing belt can result in damage to internal engine components.

Nov 19, 2010 | 2000 Audi A8

1 Answer

Have a 2.5tdi pd touareg. need timing marks?

the timing marks for all vw/audi/seat and skoda are on the front pulleys(they are small dots)you may need to highlight them with chalk.

May 10, 2010 | 2004 Volkswagen Touareg

1 Answer

Got audi a4 1996 diesel need to change cambelt but

A diesel uses a different procedure. You'll need a tool to hold the camshaft pulley parallel to the top of the cylinder head. The timing mark to set TDC for piston #1 is located on top of bell housing. The pointer must be aligned on the diamond cut on the flywheel. A VW/Audi setting bar tool #2065A is needed to lock the camshaft in position. Lock the injection pumpin position using the special lock pin (VW/Audi special tool no. 2064). Caution: If the drive belt is broken or has jumped time, do not attempt to lock the sprocket at this time!!! You will also need VW/Audi special tool no. VW210 to measure belt tension between camshaft sproket and injection pump sprocket. So good luck.

May 01, 2010 | 1996 Audi A4

2 Answers

What's the correct way of installing the camshafts on an Audi 1.8T B6 motor?

align timing marks on furthermost bearing caps on exhaust and inlet side to respective camshaft sprockets. to confirm correct fitment, their should be 16 chain links starting from one timing mark to the other.

Apr 20, 2010 | 2002 Audi A4

2 Answers

My Audi 80 can't start after changing the timing belt, water pump and the cam belt, wht is the problem?

The valve timing must be out. You will need to verify that the timing marks on your camshaft sprocket(s) are set at the correct position when you rotate the engine to the compression stroke on TDC.

Sep 30, 2009 | 1992 Audi 80

1 Answer

How do i set the timing for audi A6 2003

there are actually special tools the cam has no timing marks the tool only goes on one way and locks the cams in place and it is actually a long process but there is no way to do it without the cam lock

Aug 20, 2009 | 2003 Audi A6

1 Answer

Does the 2.8 a6 have timing mark and where are they


Feb 20, 2009 | 1999 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79865 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14411 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides