Question about Cars & Trucks

Open Question

Base plate - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove four blade base plate from masport 450 series


use hole where bolt for blade goes insert a large screwdriver or steel rod and get it to catch on the casting or at the grass throw end with base locked you can now undo lock nut. should be lefty loosy.

Feb 26, 2017 | Cars & Trucks

1 Answer

Car lopes as soon as it warms up


idle air control is looking for base idle. throttle body base idle plate is dirty with carbon. cleaned out throttle plate with carb cleaner and tooth brush. use rags to catch black carbon.open plate.by some one hold throttle plate open with gas pedal. engine not running. after completed, start engine. run 1500 prm for a short time to clean out excess fluid. that should fix your problem..

Jan 18, 2013 | 1991 Chevrolet Corvette

1 Answer

Thermostat replace


YOOLS U NEED= Basic hand tools will probably do the trick. You may need a rachet and set of sockets.

1

Cut the furnace's power source before beginning. Check for a power switch near your furnace or turn off the electrical power supply at the circuit breaker.

2Turn off the gas supply if you have a gas furnace. Look around the furnace for a black pipe. This pipe is the gas line. Check for a valve located near the pipe. Turn off the gas supply by moving the valve so it's perpendicular to the gas line.

3

Take off the thermostat's old cover by unscrewing the screws that attach the cover to the wall. Some covers don't have screws and simply pull off.

4

Unscrew the mounting plate and notice the wires.
5

Place a small piece of masking tape on each wire. Use a felt-tip marker to mark the masking tape according to the wire's screw terminal location. Usually, the wires are marked with letters.

6

Disconnect the low-voltage wires from the base plate by loosening the screws and then pulling the wires away.
7

Locate the mounting screws for the base plate. Unscrew them and take off the base plate. Guide the base plate over the wires carefully.

May 31, 2012 | 1997 Toyota Avalon

1 Answer

Wheres the idle air mixture screw at


On the bottom carburator base plate, facing the front

It would be hard to imagine that the plug is still in there,
so you can not see it

If so, the carb comes off & you saw two slots in the base plate
& break off the remaining tab & drive out the plug

Sep 24, 2011 | 1987 Chevrolet Nova

1 Answer

Seperate rearview mirror from plate both came off


f

Replacing the rear view mirror on a Ford Explorer is easy. The only obstacle you might encounter is fear of breaking the glued metal plate off the windshield. Do not sweat it. You can buy glues at the auto parts store to reattach the mirror to the windshield (Difficulty: Moderately Easy).

Instructions:
  1. Tap gently at the base of the mirror where it slides on over the metal plate glued to the windshield and pull upward. Some rear view mirrors have a small Allen screw that tightens the base of the rear view mirror to the metal plate. Disconnect the electrical plugs if your rear view mirror has them.
  2. Pull the rear view mirror clear of the metal plate. Clean around the metal plate glued to the windshield. If the metal plate has come off because of harsh weather or from hammering too hard at it, reattach it with glue designed for this job.
  3. Clean the area where you will be attaching the metal plate on the windshield. Apply the glue evenly on the surface of the metal plate that will go against the window. Be sure to clean and scrape off all the old glue before applying the new glue. Gently push the metal plate against the windshield in the spot you wanted it and hold tight for five minutes.
  4. Wait a day before putting the base of the mirror or replacement rear view mirror onto the metal plate. Do not force the base over the plate. Forcing it will likely dislodge it again. Press firmly until it will not slide along the grooves of the metal plate. Reconnect your electrical plugs and tighten the Allen screw if your new mirror has one. Adjust the mirror according to your safe viewing preference

Hope help with this (remember rated this help). Good luck.

Mar 12, 2010 | 1999 Ford Explorer

1 Answer

Jetta 1991 carb.car does not want to idle after 4000 rpm.changed carb , base plate , gasket on intake manifold.no luck


TOOK THE CAR TO BOSCH DEALER AND RUN A FEW TESTS ONLY TO FIND THAT THE AFTER MARKET CARB AND BASE PLATE DID NOT WORK AS GOOD AS GENUINE VW PARTS.AFTER MARKET CARB HAS 2 VACUMS AS GENUINE VW HAS 1 AND THE AFTER MARKET BASE PLATE IS MORE FLEXABLE THAN GENUINE.I INSTALLED GENUINE VW PARTS NOW AND IT SEEMS MY PROBLEM IS SOLVED FOR NOW.

Feb 16, 2010 | Volkswagen Jetta Cars & Trucks

1 Answer

Engin oil leaking past distributer base plate


There is a seal between dist and engine. If distributor is properly tightened and still leaking, replace the seal. Get a manual ...if you do this incorrectly, you will alter ignition timing.

May 22, 2009 | 1996 Volvo 850

1 Answer

Oil filter base plate


it does have an O ring buts its irregularly shaped. it is usually held on by 3 bolts(mine was). and the top most bolt was very close to my oil pressure sensor....(had to take it out to avoid breaking it) i needed a very short ratchet wrench and get it out. Make sure you get the ring from a Honda Dealership if you can.(i have bad luck with aftermarket parts on my Hondas).The reason why mine was spraying is because the baseplate was actually cracked. so i also had to buy a new one ( yes they have them too) O-ring 12.00 bucks baseplate was 39.00 bucks for me, might be a bit more for yours since your Honda is a little newer (mine was an 89 accord) oil filter baseplate or mountplate are some terms (so you were right on) hope this helps.

Mar 08, 2009 | 1993 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...