Question about Ford Cars & Trucks

Open Question

Rod bearings torque down to wat on a 2008 Ford fusion se with a 2.3 liter engine

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: torque specs.

connecting rod = first pass 18 ft lbs , second pass 75 degrees

main bearings = first pass 37 ft lbs , second pass 77 degrees

wow that wasn't easy to find for some reason .

Posted on Jan 01, 2009

moparownr
  • 667 Answers

SOURCE: main and rod bearing torque specs

do you have a Haynes Manual or Chilton? if not check your local library, they may have one, the specs are in there

Posted on Mar 31, 2009

  • 1779 Answers

SOURCE: 2008 ford fusion alerts on dashboard

You can download a free owners manual from this site, it will identify all the dashboard alerts:
https://www.fleet.ford.com/maintenance/owners_manuals/results.asp

Posted on Aug 13, 2009

terseo
  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

drsinister69
  • 2317 Answers

SOURCE: What is the right Torque Specification of the

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

Posted on May 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What's the torque on rod bearings?


Engine Noises ' Knocking and Ticking ' Common Causes

www.justautorepair.com/whats-wrong-with-my.../knocking-ticking
The following are causes of connecting rod bearing noise: ... Loose torque converter-to-flywheel or flywheel-to-crankshaft bolts will sound similar to bearing knock. .... I got a 1998 tahoe its making a lil ticking noise after I got unstuck on some ice ... 2001 FordTaurus with a loud mechanical noise that is constant when engine ...

Change 4.6L rod bearings with engine still in vehicle? 02 Explorer ...

www.ford-trucks.com > ... > Modular V8 (4.6L, 5.4L)
Aug 11, 2011 - The regular everyday rattling noises seemed to get louder than usual. ...So I dropped the pan and this is what I found: ... Is it possible to change the rod bearings with the engine still in the vehicle? ... If you decide to go with new bearings,torque your caps down on some plasti-gauge and see if you get the ... 7.3 engine r&r
Mar 22, 2012
Rod Bearing Replacement
Dec 27, 2010
More results from www.ford-trucks.com

Dec 28, 2015 | 2000 Ford Explorer

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Torque specs for rod & main brgs for 1994 ford f150, 300 6 cyl fuel inj engine


Main Bearing Cap Torque:
Torque in 2 steps: Step 1: torque to 35 Ft/Lbs Step 2: torque to 70 Ft/Lbs

The Rod Bearing Cap Torque: 45 Foot pounds (Final torque)

Was this what you needed...let me know by your rating of me...thanks!

Sep 17, 2011 | 1994 Ford F150 Styleside Supercab

2 Answers

Rod bearings torque on cap nuts do you know what it is torqued at


Hello terrychadwic

If you have the 3.3 or 3.5 engine the torque is 40 foot pounds + 1/4 turn.

Regards,
netvan

Mar 04, 2011 | 1996 Chrysler Concorde

1 Answer

I am looking 4 the torque pressures (ft.lbs) on the main crank bearings, and rod bearings on a 2007 Ford 5.4 3 valve engine??? Gerry..............thank-you


mains - vertical bolts first 30 ft.lb. PLUS 90 degrees
pattern frt

8 7
4 3
2 1
6 5
10 9
side bolts
22 ft. lb plus 90 degrees
pattern frt

7 8
3 4
1 2
5 6
9 10

connecting rod caps cracked type rod-rod and caps must be kept in matched sets, recommend new bolts/nuts, spec is 32 ft lb. plus 105 degrees - torque each item to the correct torque then go back and do the degrees. these are torque to yield bolts and the procedure is very important.

Oct 02, 2010 | Ford F-150 Cars & Trucks

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

I need the torque specs for the main and rod bolt for a 99 escort 2.0l engine


engine tightening torques
Main bearings Renew bolts/nuts No
Main bearings Stage 1 43 Nm
Main bearings Stage 2 85 Nm
Big end bearings Renew bolts/nuts Yes
Big end bearings Stage 1 15 Nm
Big end bearings Stage 2 90°

Jan 21, 2010 | 2004 Ford Focus

1 Answer

Needing engine bolt torque specifications for a 2006 Ford Five Hundred with 3.0 liter engine. This will need to include rod and mains torque and torque rotation.


stage 1 tighten to 30 ft pounds
stage 2 tighten 90 degrees
stage 3 loosen one full turn
stage 4 tighten to 30 ft pounds
stage 5 tighten 90 degrees
stage 6 tighten 90 degrees
this is per mitchell on demand courtesy of ford specs on the lft and right head.
for some reason there are no torque specs on mitchell for connecting rods and mains.

Sep 15, 2009 | 2006 Ford Five Hundred

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

1 Answer

Torque specs


2002 2.0L Duratech.

Don't have 2004 2.3L

  • NOTE: Use new connecting rod bearing cap bolts.
    NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
    Install the bearing caps.
  • Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.
  • Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.
  • Coat the inner side of the bearing shells with engine oil.
  1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
    Tighten the main bearing and connecting rod bearing bolts.
    1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.
96fc939.gif

Apr 28, 2009 | 2004 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...