Question about Cars & Trucks

Open Question

I have an antler suitcase carbon fibre (?) the wheels are breaking up and need replacing . Can you do this and .if so, how do I go about it? I reside in Scarborough Northside. Norman Emery.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cruise control diagram for 2002 expedition


This could be one of two things and neither requires a schematic.
1. There is a wire harness inside the steering column called a clock spring. It has to twist every time you turn the wheel. They break.
2. The pads or switches are carbon impregnated rubber and they loose conductivity over time. You can either clean them with alcohol or you can replace them..
The issue is you have to pull the steering wheel off to do some of this and it can require special tools.

Jul 30, 2016 | 2002 Ford Expedition

1 Answer

Where is the vapor canister purge valve located on a 96 Cadillac deville Northstar


If your purge valve/solenoid is failing, chances are you will need a new EVAP Carbon Canister as well. As the canister gets old the charcoal (carbon) starts to break down and bits gets sucked and stuck in the valve when the gases are purged from the canister on start up and acceleration. If you take the solenoid off and tap it on the ground you will probably see tiny bits of carbon fall out. This is a sure sign that you need a new canister ...Just replacing the solenoid valve won't help as it will only get clogged again by these bits of carbon. GM located most canisters in the rear wheel well under the wheel well lining. Not too sure of your model but check a Manuel. You must also blow out the line before connecting it to the new canister as bits of carbon can be still in the line and contaminate the new purge valve.

Mar 27, 2015 | Cadillac Cars & Trucks

1 Answer

1987 chevy corvette rear end sways


Well its a american muscle car and no doubt the bushes are worn somewhere,its the drivers fault as a muscle car can only do straight lines ,and not bends like a europeon sports car and it looks like someone has tried to do the dreaded bends with a american car causing the bushes to wear out .boy do i love winding up you americans about this -----till i watched top gear last week and hey a new stingray out with rear wheel drive only but all new suspension in carbon fibre on a race track against a porsche with 4x4 and guess what the stingray won ,no sliding or anything in fact it was the porsche that was slipping .and its its 20.000 GBP cheaper than anything else near it mainly the F type jag ,but then your talking different class with a JAGUAR ,i know i have one

Feb 27, 2015 | 1987 Chevrolet Corvette

1 Answer

I put the kit on my 3.4v6 Chevy camaro and oil sensor but my oil still marks low when engine gets warmed up is there a screen inside oil pan


would need to see it to know whats wrong sorry ,but i saw the new one on top gear brit TV and the new chevy corvette with all that carbon fibre suspension went faster than a porshe around the circuit and didnt kick out ,i mean this is a first a american muscle car that can do bends as well and still cheaper than a F type jag or a porsche ,over 20.000 pounds cheaper than the cheapest europeon sports car and its only rear wheel drive not 4x4 like the porsche ,

Feb 25, 2015 | Chevrolet Camaro Cars & Trucks

1 Answer

I have a burning rubber smell coming from left rear on my 2001 silverado after driving


You may have a stuck brake shoe. The smell is more likely a burning carbon smell, which would be the break pad itself. You will need to crawl under and see if any visible burn marks or burned wires are present. Outside that, move to the actual break. 1 possible sign would be large amount of "dust" on the wheel and around the actual break, more than with the other 3 wheels.

Oct 01, 2012 | 2001 Chevrolet Silverado 1500

1 Answer

My 2000 For Expedition is running rough after new spark plugs


If you only changed the plugs and then noticed the missing then renew the leads ,these are carbon fibre not copper like the good old days and the sheer fact of you pulling them off has made them fail

Nov 07, 2011 | 2000 Ford Expedition

1 Answer

2008 140 460 series d wheel transit. egr valve keeps failing every approx 40000klms. Why? Is there a revised EGR valve to replace the current problem valve? It's very dangerous whilst driving due...


MOST VALVES DON'T GO BAD THEY JUST GET A PIECE OF CARBON STUCK IN THEM CARBON IS LIKE HARD MORTAR A LILTTLE PIECE BREAKS OFF A VALVE OR SOMTHING AND STICKS IN EGR VALVE MAKES THE CAR RUN LIKE **** USE BETTER GAS AND INJECTER CLEANER ON REGULAR BASIS THIS IS ABOUT THE BEST YOU CAN DO FOR THIS PROBLEM

Mar 03, 2011 | Ford E-Series Van Cars & Trucks

1 Answer

Blower motor on 95 buick riv


will look around before trying to walk you through it here ..soo many words to describe ..basically the 'suitcase' the black plastic housing under dash needs opened up and blower motor resides in there..squirrel cage design should be visible

Dec 16, 2008 | 1995 Buick Riviera

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...