Question about GMC Cars & Trucks

1 Answer

Replacing IAC valve in a 1994 GMC suburban - GMC Cars & Trucks

Posted by on

  • Sunie Lavender
    Sunie Lavender May 09, 2017

    Hopefully can fix it today



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has achieved Level 3.

  • GMC Master
  • 923 Answers

When will you be starting (the replacement process)?

Posted on May 09, 2017

Testimonial: "Today hopefully"

  • Sunie Lavender
    Sunie Lavender May 09, 2017

    Will try to replace today

  • solver2010 May 09, 2017

    Go to any Autozone, O'Reilly Auto Parts, or NAPA Auto Parts store, and tell them what you think you need, and why you think that!



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I broke off the IAC valve in the throttle body in a 1994 GMC Sierra 4.3lt.. need to know how to get it out. Please help!

if accessible from a good angle Need to drill in to the broken part in the throttle body using a drill bit a bit smaller then the IAC thread as close as possible to the throttle body thread U need rethreading tap similar to the IAC valve if available in size and thread run thru to clean the throttle body thread and replace with new one if no access to it need take out throttle body U have to take Ur time.
Good Luck

Dec 21, 2016 | 1994 GMC Sierra

1 Answer

1993 gmc suburban rough idle, stall in reverse

Idle air control (IAC) control rpm idle during idle.

Test it on idle with ALL electrical on full force.
RPM should increase.
If RPM remain the same then IAC is question.

Jan 13, 2014 | 1993 GMC Suburban

1 Answer

1995 P30 7.4L IDLE HI 1200 RPM SHOULD BE 850 RPM

can be the IAC valve, purge valve, and possibly MAF sensor.

Jun 12, 2011 | 1995 GMC Suburban

1 Answer

What is the teeth count on a flywheel for a 1994 5.7L 2WD gmc suburban. Also what is the balance, internal...???

need to know why the teeth count?? and for the balance it is on the flywheel itself.are you replacing a starter or what.???

Jan 25, 2011 | 1994 GMC Suburban

1 Answer

1990 v1500 gmc suburban 5.7L, what is the proper

i do not know but give these websites a try and wish you the best of luck Michigan Man.

Mar 06, 2010 | 1990 GMC Suburban

2 Answers

1994 gmc pickup- starts but when you put it in gear it dies, give it gas it will run but not good

It sound like your idle air control (IAC) valve is dirty and the fuel injectors. Try cleaning the throttle body and IAC with throttle body cleaner, if it's really bad you may have to use two cans of throttle body cleaner to make sure you have all of the carbon and varnish cleaned out. If this does not help, then there is a good chance that the IAC has gone bad and needs to be replaced but also check the wire harness to the IAC and TPS on the throttle body. Good luck and hope this helps and it would not hurt to replace the fuel filter also.

Dec 15, 2009 | 1994 GMC Sierra

1 Answer

On a 1994 gmc suburban recieving code 78

Code 78 refers to the secondary fan relay circuit, I would start there, you might have a short in that circuit, or an open, or bad relay. Hope this helps, let me know

Dec 10, 2009 | 1994 GMC Suburban

1 Answer

I have a 1994 GMC 2500. Recently on a cold morning it would not shift out of first gear. After about 30 minutes of warm up it started shifting normal. After replacing the filter which was very dirty and...

It sounds like that you have a valve in the valve body, located above the filter, that is sticking due to some of the debris not caught by the clogged filter. If the trans tune does not get it then you will have to remove the valve body then remove the valves manually and clean them. Recomend that you have a professional do it due to the complex nature.

Mar 02, 2009 | 1994 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides