Question about Cars & Trucks

1 Answer

The whole parts of enjine are stript i want to put everything back including,crane shaft,cameshaft and cylinderhead and disributor

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 923 Answers

Sorry, but I never heard of a crane shaft, nor have I ever heard of a cameshaft! The correct terminology would be a CRANKshaft and a CAMshaft!

Posted on May 09, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change complete body on 93 geo tracker


how to change,? how to remove it and then? what?
its not like a light bulb....
the cars whole body, needs replacement. the whole thing.
this car has real frame, so you must detach all harness ends
from all drivline parts. including in the engine bay.
then all shift linkage.(on a 5speed it be the shifter too) after console removal (center)
then all those body to frame, bolts.
take sharp left turn and body and you falls of car. (jokinig)

now lifting it, you will need, like 8 people to do that by hand
or a gantry crane
or a huge tree and chain hoist.
lifting the body, invites damage to the body, or to the newone going back on. It can be done with many jacks and huge boards to protect t
the body, and jack up the body in stages, and then slide the rolling
chassis from under the body.
my guess? is you have a car with good body bad driveline
then one more bad body with good driveline, right, is that the store?

Oct 11, 2014 | 1993 Geo Tracker

1 Answer

.comGood day. I have a


even though it may look exactly the same ,the water ports on the block might not line up.

Aug 04, 2011 | Ford Focus Cars & Trucks

2 Answers

I have no spark any reason that comes to mind?


possible distributor. most of the time spark is produced by distributor

Mar 25, 2011 | 1992 Honda Accord

1 Answer

Replaced u joints on 1989 Montero rear drive shaft. Now drive shaft has vibration which peaks around 65 mph. Think I reassembled wrong or bad part(s)? Used Precision not OEM Mitsubishi u joints.


When you took it apart did you "match mark" the joints so that it went back together the same? If not then your driveshaft is probably out of balance. Any driveline shop can correct this. By match marking I mean that you make a mark on each piece of the driveshaft so that when you put it back together the pieces are in the same position relative to each other. If one piece got put back 180 degrees out, it can cause the whole shaft to become unbalanced.

Dec 24, 2010 | 1989 Mitsubishi Montero

1 Answer

Check enjine lite stays on-surging engine at idle


Test the cam shaft position sensor. The best thing to do is have and engine code scan done which many part stores will do for free. This will pinpoint exact problem location. It is either a bad sensor or circuit.

Apr 11, 2010 | 2004 Mazda 6

1 Answer

Install a disributor in chevy 350


Remove the valve cover from the driver's side and turn the engine over until you see the intake valve open and close and the exhaust valve start to open. Turn the engine timing mark back to 0 on the timing marker. That will be TDC. Put the rotor button on the distributor and set it at 3 o'clock. As you put the distributor in the rotor button will turn and should be in the 5 o'clock position when seated. That is the position for #1 plug. It is a snug fit but don't force it. If it won't go all the way down, the shaft may not be lined up with the oil pump. A long screwdriver can be used to turn the oil pump to line up if needed. If it doesn't line up at 5 o'clock, you'll have to pull it back out and turn the rotor one tooth and try it again. Hope this helps.

Oct 28, 2009 | 1989 Chevrolet C1500

2 Answers

Suzuki Vitara 1996 V6 2L assembly problems


The suzukiinfo.com site has a whole heap of free genuine manuals you can download and print out.
www.suzukiinfo.com

Aug 20, 2008 | 1999 Suzuki Vitara

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...