Question about Saturn Cars & Trucks

Open Question

I need the location of brake lines on master cyl on1999 saturn sl1

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 186 Answers

SOURCE: need to replace left side drive shaft on my 1999 saturn sl1

Drain Trans,Remove lower ball joint nut & separate the knuckle from ball joint.Remove 30mm axle nut & gently pry out the axle from trans then tap out axle from hub.

Posted on May 08, 2009

  • 299 Answers

SOURCE: 2001 Saturn Sl1 1.9 Code P0404

Spray carb cleaner around #1 intake runner,known to blow gasket there,Replace leaner egr valve.

Posted on Jun 17, 2009

  • 5 Answers

SOURCE: Changing spark plugs on 2001 SL1 Saturn V-4

Remove the plugs, make sure the new plugs are gapped to .040, put anti-seize on the threads of the new plugs, then install them and tighten accordingly.

Posted on Aug 25, 2009

  • 158 Answers

SOURCE: 00 Chevy EHCU HELP

bleed each separately

Posted on Aug 29, 2009

ZJLimited
  • 17970 Answers

SOURCE: I need a diagram to show where the brake lines hook into mst/cyl

I suggest check the Ford 1964-1973 Mustang

Hope helps (rated this) Good luck.

Posted on Jan 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would happen if u bleed the master cylinder while it was installed On1996 Saturn sl1


mostly any air trapped in the cylinder would be pushed out. It is always a good point to start if you have replaced the master cylinder before bleeding the brake lines as it primes the pistons. Just be careful to wash the area where the oil sprays as it will take the paint of if allowed to stay on

Nov 09, 2013 | Cars & Trucks

2 Answers

Clutch fluid resuvior is where


Late model cars use the brake m/cyl resevoir as asupply for the clutch system. Check for a line from theclutch m/cyl to a point in the brake m/cyl resevoir. If not follow the line back to the resevoir.

Mar 03, 2013 | 1997 Saturn SL

1 Answer

How long is the main brake line on a 91 saturn sl1? NO ABS


You get under the car & measure what you will need,
& write down all the different tubing lengths,fittings,etc

You will have to cut,double flair & bend tubing-- so get extra

Dec 05, 2012 | Cars & Trucks

1 Answer

Master brake bleeding


Don't need to bleed a master cylinder

When you have some inside pushing on the
brake pedal, as you open & close the bleeders, the fluid
will leave the master & go out the open caliper or wheel cyl

Oct 08, 2012 | 1995 Saturn Sl

1 Answer

1997n saturn sl1 front brakes didnt need replaced but back brakes were replaced. horrendous scrubbing noise still there- no leaks from brake fluid, are there issues with master cylinder??


Take it to another repair shop and tell them to look at the front end and figure out what is wrong. There are no mechanical parts in the master cylinder which would make a scrubbing noise. If the front pads are good, you could still have a caliper or bearing problem.

Jul 10, 2011 | 1993 Saturn SL1

2 Answers

I HAVE A 1996 SATURN SL 1 I HAVE NO BRAKE PEDAL SO REPLACED MASTER CYLINDER 2 TIMES GET FLUID BLEED OUT WITH CAR NOT RUNNING HAVE GOOD PEDAL GO TO START CAR LOSE ALL PEDAL HAVE NO BRAKES FLUIDNOT COMING...


MASTER CYLINDER SHOULD BE BENCH BLED BEFORE INSTALATION.PUT MASTER CYL. IN VISE-SHOULD HAVE COME W/RUBBER TUBES & ADAPTERS TO CURCULATE FLUID FULL STROKE OF CYL. TILL ALL AIR BUBBLES ARE GONE.THEN INSTALL MSTR CYL./GETT SOMEONE TO PUMP BRAKES THEN HOLD PEDAL FIRMLY WHILE YOU RELEASE BLEEDER VALVES ONE AT THE TIME FARTHEREST FROM THE MSTR CYL. TILL ALL AIR IS PURGED. REPEAT STEPS TO EACH BLEEDER TILL ALL HAVE BEEN DONE.GOOD LUCK W/THAT!

Mar 30, 2011 | 1996 Saturn SL

2 Answers

No Brakes, changed Booster, thought it was air in the lines. When bleeding no fluid coming out of front right and back brake bleeder valves. Checked rubber line, is ok. Clogged somewhere in the line. Have...


Is the master cylinder good? a bad master can cause this also did you bleed the master first before bleeding at the wheel and also make sure the bleeder screw is clean, if the hose is good then theres only a few things, a bad master or a master that wasnt bleed, try bleeding the master first then try rebleeding the brakes.

Mar 01, 2011 | 1983 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...