Question about Cars & Trucks

Open Question

I have a test

Test

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiper control module location on a 2000 f250


Did you check the wiper relay's in the under hood fuse box ? There are two ,wiper run/park relay & wiper high low relay ! Also ,did you check fuse's ? fuse # 11 - 30amp location cental juction box . The wiper switch is a input to the GEM module . Generic electronic module . The module in most cases isn't the problem ! Learning how to test these electronic systems is , people do not know how to test so they just replace parts . What they should do is take the vehicle to ford certified Technician who has the knowledge and testing equipment to find an fix it .

The generic electronic module (GEM) receives inputs from the following:
  • multifunction switch
  • anti-lock brake control module (vehicle speed signal [VSS])
  • ignition switch
The GEM uses these inputs to control the outputs to the following:
  • windshield wiper high/low relay
  • windshield wiper run/park relay
  • windshield washer relay
  • rear wiper motor relay
  • rear window washer relay

  • GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1240 Wiper Washer Rear Pump Relay Circuit Failure GEM GO to Pinpoint Test K . B1241 Wiper Washer Rear Pump Relay Circuit Short to Battery + GEM GO to Pinpoint Test K . B1342 ECU is Defective GEM CLEAR the DTCs. REPEAT the GEM self-test. If DTC B1342 is retrieved, INSTALL a new GEM. REFER to Section 419-10 . B1431 Wiper Brake/Run Relay Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers stay on continuously, GO to Pinpoint Test C . B1432 Wiper Brake/Run Relay Circuit Short to Battery GEM GO to Pinpoint Test B . B1434 Wiper Hi/Low Speed Relay Coil Circuit Failure GEM GO to Pinpoint Test D . B1436 Wiper Hi/Low Speed Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test D . B1438 Wiper Mode Select Switch Circuit Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If both the windshield and rear window wipers are inoperative, GO to Pinpoint Test L . B1441 Wiper Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test C . B1446 Wiper Park Sense Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the speed dependent interval mode does not operate correctly, GO to Pinpoint Test G .
    If both windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1450 Wiper Wash/Delay Switch Circuit Failure GEM If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F .
    If both the windshield and rear wipers are inoperative, GO to Pinpoint Test L . B1453 Wiper Wash/Delay Switch Circuit Short to Ground GEM If the windshield wipers stay on continuously, GO to Pinpoint Test C .
    If the wash and wipe function does not operate correctly, GO to Pinpoint Test F . B1458 Wiper Washer Pump Motor Relay Circuit Failure GEM GO to Pinpoint Test F . B1460 Wiper Washer Pump Motor Relay Coil Circuit Short to Battery GEM GO to Pinpoint Test F . B1473 Wiper Low Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper speed does not operate correctly, GO to Pinpoint Test E . B1475 Accessory Delay Relay Contact Short to Battery GEM REFER to Section 501-11 . B1476 Wiper High Speed Circuit Motor Failure GEM If the windshield wipers are inoperative, GO to Pinpoint Test B .
    If the windshield wipers do not operate at high or low speed correctly, GO to Pinpoint Test D .
    If the intermittent windshield wiper does not operate correctly, GO to Pinpoint Test E . B1611 Rear Wiper Mode Switch Circuit Failure GEM GO to Pinpoint Test H . B1614 Rear Wiper Mode Switch Circuit Short to Ground GEM GO to Pinpoint Test I . B1820 Rear Wiper Motor Up Relay Circuit Short to Battery + GEM GO to Pinpoint Test H . B1839 Rear Wiper Motor Circuit Failure GEM GO to Pinpoint Test H . - All other DTCs. GEM REFER to Section 419-10

Jun 06, 2017 | Ford F-250 Cars & Trucks

1 Answer

What does code dtc3 fail mean on my emissions test,,97 nissan pathfinder


I means that the vehicle failed it's emissions test as it failed the digital trouble code reading test 3
the testing station tests the exhaust emissions and the onboard computer
Your computer failed the test

May 16, 2017 | Nissan Cars & Trucks

1 Answer

The heat in my 2007 ford edge only blows hot air out of the passenger side, while the driver side gets cold air


Have it checked for DTC'S - diagnostic trouble codes .
Electronic Automatic Temperature Control (EATC) Module DTC Chart NOTE: Some PCM DTCs may inhibit air conditioning (A/C) operation. If any PCM DTCs are retrieved, diagnose those first. Refer to the Powertrain Control/Emissions Diagnosis (PC/ED) manual. DTC Description Action to Take B1251 A/C In-Vehicle Temperature Sensor Open Circuit Go To Pinpoint Test A . B1253 A/C In-Vehicle Temperature Sensor Circuit Short to Ground Go To Pinpoint Test A . B1255 A/C Ambient Temperature Sensor Open Circuit Go To Pinpoint Test B . B1257 A/C Ambient Temperature Sensor Circuit Short to Ground Go To Pinpoint Test B . B2427 RH A/C Solar Radiation Sensor Circuit Short to Ground Go To Pinpoint Test C . B2426 RH A/C Solar Radiation Sensor Open Circuit Go To Pinpoint Test C . B2795 LH A/C Solar Radiation Sensor Circuit Short to Ground Go To Pinpoint Test C . B2796 LH A/C Solar Radiation Sensor Open Circuit Go To Pinpoint Test C . B2014 Evaporator Temperature Sensor Circuit Open Go To Pinpoint Test D . B1947 Evaporator Temperature Sensor Circuit Short to Ground Go To Pinpoint Test D . B295A LH Blend Door Potentiometer Feedback Circuit Open Go To Pinpoint Test F . B295B LH Blend Door Potentiometer Feedback Short to Ground Go To Pinpoint Test F . B226C LH Blend Door Motor Stalled Go To Pinpoint Test F . B295C RH Blend Door Potentiometer Feedback Circuit Open Go To Pinpoint Test F . B295D RH Blend Door Potentiometer Feedback Short to Ground Go To Pinpoint Test F . B226D RH Blend Door Motor Stalled Go To Pinpoint Test F . B295E Mode Door Potentiometer Feedback Circuit Open Go To Pinpoint Test F . B295F Mode Door Potentiometer Feedback Short to Ground Go To Pinpoint Test F . B226E Mode Door Motor Stalled Go To Pinpoint Test F .
Need to use a professional scan tool to check these codes !

Dec 28, 2016 | 2007 Ford Edge

1 Answer

Why is it my 2008 chevy uplander rear wiper motor/blade moves some and stops. I let van set 5-10 minutes with key off. Turn on key. Wiper motor/blade moves a few degrees and then stops again. Why?


Can you move the wiper by hand ? Which does your vehicle have ?
WDA/Z88 The rear wiper is controlled based on an input from the rear wiper/washer portion of the multifunction switch. When closed, the wiper ON and wiper DELAY switches provide a unique voltage signal to the rear window wiper motor indicating the desired speed. Each switch has a unique resistor that drops the voltage to a specified value which is interpreted by the rear window wiper motor as ON or DELAY. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
W49 The rear wiper is controlled based on an input from the rear wiper/washer switch. When closed, the wiper ON switch provides a voltage signal to the rear window wiper motor indicating rear wiper operation is requested. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
Do you know how to do electrical testing ?
WDA/Z88
  1. Ignition OFF, disconnect the harness connector X1 at the multifunction switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 4 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the multifunction switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, test for B+ between the signal circuit terminal D and ground.
  12. ?‡'
    If less than the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, test or replace the multifunction switch.

  13. Rear wiper switch in the DELAY position, test for B+ between the signal circuit terminal D and ground.
  14. ?‡'
    If less than the specified value, test or replace the multifunction switch.

  15. If all circuits test normal, test or replace the rear window wiper motor.
W49
  1. Ignition OFF, disconnect the harness connector at the rear wiper switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the rear wiper switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, verify a test lamp illuminates between the signal circuit terminal D and ground.
  12. ?‡'
    If the test lamp does not illuminate, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the I/P switch assembly.

  13. If all circuits test normal, test or replace the rear window wiper motor.
Component Testing

Do you know how

Jun 09, 2016 | 2008 Chevrolet Chevrolet Uplander LS

1 Answer

2012 Chevy Silverado low beam light not working.


Regular headlamps or HID ? Check the HDLP LO/HID relay in the under hood fuse / relay box . Will be marked on the inside of the lid . Do you know what a BCM is ? body control module. Could have DTC'S - diagnostic trouble codes stored .
DTC 2575 00: Headlamp Low Beam Control Circuit
  1. Ignition OFF, disconnect the low beam relay.
  2. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
  3. ?‡'
    If the test lamp illuminates, test the control circuit for a short to voltage.

  4. Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
  5. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.

  6. Verify that a test lamp illuminates between the B+ circuit terminal 86 and ground.
  7. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  8. Ignition OFF, disconnect the harness connector at the inoperative low beam headlamp.
  9. Ignition OFF, scan tool OFF, exterior lamps OFF, test for less than 5.0 ohms between the ground circuit terminal B and ground.
  10. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  11. Connect the harness connector at the inoperative low beam headlamp.
  12. Connect a 40A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the low beam headlamps are activated.
  13. ?‡'
    If the low beam headlamps do not activate, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the inoperative low beam headlamp.

  14. Connect a test lamp between the B+ circuit terminal 86 and the control circuit terminal 85.
  15. Command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
  16. ?‡'
    If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM.


    ?‡'
    If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.

  17. If all circuits test normal, test or replace the low beam relay.

May 25, 2016 | Cars & Trucks

1 Answer

Hi i have just changed steering wheel on fiesta zetec 2003 for a ST150 2005 steering wheel will the air bags and connections be compatable with each other.


. Were did you check for codes ? an what are you checking with ? you need a factory scan tool to check for those type codes ? or the light flashes codes
Lamp Fault Code (LFC)
When the RCM detects a fault, it will cause the air bag indicator to flash a coded sequence called a LFC. The code is one digit. The digit is indicated by a number of flashes with a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indicator will remain lit as long as the key remains in the RUN position. If there are multiple LFCs, each LFC will flash in order of priority.
Each LFC has one or more associated DTC.
  1. Press TRIGGER. The RCM will run the On-Demand Self-Test and display On-Demand DTCs (reflecting hard system concerns) on the screen.


Restraints Control Module (RCM) DTC Index DTC LFC LFC Priority Description Action - Continuous 1 Air bag warning indicator is illuminated continuously Go To Pinpoint Test B . B1231 Continuous 3 Longitudinal acceleration threshold exceeded (Crash Occurred) Go To Pinpoint Test C . B1318 Continuous 4 Battery voltage low REFER to Section 414-00 . B1342 Continuous 2 RCM is defective DIAGNOSE and REPAIR other DTC(s) that are present. CLEAR the DTCs. REPEAT the self test. When or if DTC B1342 alone is present, INSTALL a new RCM. REFER to Restraints Control Module (RCM) in this section. CLEAR the DTCs. REPEAT the self test. B1462 N/A N/A Safety belt switch circuit failure Go To Pinpoint Test AN . B1869 Continuous or Tone 39 Lamp air bag warning indicator circuit open Go To Pinpoint Test AJ . B1870 Tone 41 Lamp air bag warning indicator circuit short to battery Go To Pinpoint Test AK . B1876 4 24 Safety belt driver pretensioner circuit failure Go To Pinpoint Test T . B1877 4 23 Safety belt driver pretensioner circuit open Go To Pinpoint Test S . B1878 4 22 Safety belt driver pretensioner circuit short to battery Go To Pinpoint Test R . B1879 4 36 Safety belt driver pretensioner circuit short to ground Go To Pinpoint Test AF . B1880 4 27 Safety belt passenger pretensioner circuit failure Go To Pinpoint Test W . B1881 4 26 Safety belt passenger pretensioner circuit open Go To Pinpoint Test V . B1882 4 25 Safety belt passenger pretensioner circuit short to battery Go To Pinpoint Test U . B1883 4 38 Safety belt passenger pretensioner circuit short to ground Go To Pinpoint Test AH . B1885 4 37 Safety belt driver pretensioner circuit resistance low on squib Go To Pinpoint Test AG . B1886 4 39 Safety belt passenger pretensioner circuit resistance low on squib Go To Pinpoint Test AI . B1915 3 10 Air bag driver circuit failure Go To Pinpoint Test F . B1916 3 8 Air bag driver circuit short to battery Go To Pinpoint Test D . B1920 3 13 Air bag passenger circuit failure Go To Pinpoint Test I . B1925 3 11 Air bag passenger circuit short to battery Go To Pinpoint Test G . B1932 1 9 Air bag driver circuit open Go To Pinpoint Test E . B1933 2 12 Air bag passenger circuit open Go To Pinpoint Test H . B1934 1 29 Air bag driver inflator circuit resistance low on squib Go To Pinpoint Test Y . B1935 2 31 Air bag passenger inflator circuit resistance low on squib Go To Pinpoint Test AA . B1936 3 28 Air bag driver circuit short to ground Go To Pinpoint Test X . B1938 3 30 Air bag passenger circuit short to ground Go To Pinpoint Test Z . B1992 5 14 Driver side, side mount air bag circuit short to VBATT Go To Pinpoint Test J . B1993 5 32 Driver side, side mount air bag circuit short to ground Go To Pinpoint Test AB . B1994 5 15 Driver side, side mount air bag circuit open Go To Pinpoint Test K . B1995 5 33 Driver side, side mount air bag low resistance on squib Go To Pinpoint Test AC . B1996 6 17 Passenger side, side mount air bag circuit short to VBATT Go To Pinpoint Test M . B1997 6 34 Passenger side, side mount air bag circuit short to ground Go To Pinpoint Test AD . B1998 6 18 Passenger side, side mount air bag circuit open Go To Pinpoint Test N . B1999 6 35 Passenger side, side mount air bag low resistance on squib Go To Pinpoint Test AE . B2117 5 16 Driver side, side mount air bag low capacitance on squib Go To Pinpoint Test L . B2118 6 19 Passenger side, side mount air bag low capacitance on squib Go To Pinpoint Test O . B2141 5Hz 6 NVM configuration failure RECONFIGURE the RCM. REFER to Section 418-01 . B2226/ B2227/ B2855/ B2856 N/A N/A Front crash sensor failure Go To Pinpoint Test AR . B2228/ B2230/ B2232/ B2234 N/A N/A Air bag driver, 2nd stage fault Go To Pinpoint Test AL . B2229/ B2231/ B2233/ B2235 N/A N/A Air bag passenger, 2nd stage fault Go To Pinpoint Test AM . B2433/ B2434/ B2435 N/A N/A Buckle switch, driver failure Go To Pinpoint Test AO . B2437/ B2438/ B2439 N/A N/A Buckle switch, passenger failure Go To Pinpoint Test AP . B2477 Continuous 7 Module configuration failure Check for correct RCM for this vehicle. RECONFIGURE the RCM. REFER to Section 418-01 . B2853/ B2854/ B2873/ B2873/ U2027 5 20 Left side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test P . B2852/ B2874/ B2875/ U2028 6 21 Right side crash sensor internal fault/short to ground/VBATT/ID fault Go To Pinpoint Test Q . C1947/ C1948/ C1982 N/A N/A Seat track position sensor, driver failure Go To Pinpoint Test AQ .

Oct 14, 2015 | Cars & Trucks

1 Answer

How do I reset lift gate on 2004 lincoln navigator. It doesn't open or close anymore with the remote


Maybe your key fob needs a new battery !
Power Liftgate Initialization

NOTE:If the power liftgate system is turned OFF in the message center, the system cannot be activated with any switches or with the liftgate handle. The system will need to be turned ON for any power operation to occur.

NOTE:The power liftgate may not operate under the following conditions:

  • a low voltage or dead battery.
  • a disconnected battery
  • a power liftgate that has been left open for more than six hours.
  • a power liftgate that has been manually closed and left ajar.
If any of these conditions has occurred, the power liftgate must be reset.
  1. Manually close and fully latch the power liftgate.
  1. NOTE:If the power liftgate does not open during this step, refer to the symptom chart to diagnose the power liftgate for no operation.
    Power open the power liftgate by using the keyfob or overhead console switch.
  1. Once the power liftgate is fully open, close the power liftgate by using the keyfob or overhead console switch.
    This system can also set DTC'S
  2. POWER LIFTGATE MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX (BODY CLOSURES) 501-03 Body Closures 2004 Expedition/Navigator DIAGNOSIS AND TESTING Procedure revision date: 08/23/2004

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    DTC Description Source Action B1342 ECU Is Defective Power Liftgate Module INSTALL a new power liftgate module. REFER to Power Liftgate Modulein this section. B2477 Module Configuration Failure Power Liftgate Module REFER to Section 418-01. B2522 Vbatt1 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2552 Vbatt2 Circuit Open Power Liftgate Module GO to Pinpoint Test B. B2698 Vbatt2 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2699 Left Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2700 Right Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2701 Left Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2702 Right Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2703 Open/Close Switch Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2704 Optical Sensor Power Short To Ground Power Liftgate Module GO to Pinpoint Test B. B2705 Optical Sensor 1 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2706 Optical Sensor 2 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2709 Gate Open Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2710 Gate Close Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2711 Gate Open Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2712 Gate Close Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2713 Unlatch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2714 Uncinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2715 Cinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2718 Gate Ajar Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2721 Gate Ajar Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2722 Open/Close Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2723 Glass Position Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2724 Forkbolt Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2725 Detent Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2726 Home Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2819 Gate Motor Circuit Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2820 Gate Motor Circuit Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2821 Cincher Motor/Unlatch Actuator Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2822 Cincher Motor/Unlatch Actuator Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2825 Movement Ceased Due To Excess Speed Deviation Power Liftgate Module GO to Pinpoint Test B. B2903 Chime Output Circuit Short To Battery Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. C1935 Chime Circuit Failure Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. U1950 UBP Communication BUS Fault UBP Communi cation REFER to Section 418-00. U2338 Invalid ACM Message Data Power Liftgate Module

Feb 05, 2015 | Lincoln Cars & Trucks

1 Answer

What is it b1318 on 00 mercury cougar


Instrument Cluster Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1317 Battery Voltage High Instrument Cluster Go To Pinpoint Test C . B1318 Battery Voltage Low Instrument Cluster Go To Pinpoint Test A .
A1 CHECK THE BATTERY CONDITION
  • Carry out the Battery - Condition Test to determine if the battery can hold a charge and is OK for use. REFER to Section 414-01 .
  • Did the battery pass the condition test?
Yes
GO to A2 .

No
INSTALL a new battery. REFER to Section 414-01 . TEST the system for normal operation. A2 CHECK THE GENERATOR OUTPUT
  • Carry out the Generator On-Vehicle Load Test and No Load Test. Refer to Component Tests in this section.
  • Did the generator pass the component tests?
Yes
GO to A3 .

No
INSTALL a new generator. REFER to Section 414-02 . TEST the system for normal operation


Jan 26, 2015 | 2000 Mercury Cougar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...