Question about Cars & Trucks

Open Question

Does not shut off when lever released - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hood latch will not close.


if you look down into the latch with a flash light you should see the hood release cable. it will be attached to a lever. if the lever is stuck all the way to the drivers side than the latch is sticking. Spray some penetrating lube into the latch and then use a thin blade screwdriver to help push it the other way. Continue to spray lubricant, pull the hood release, and move the lever with a screwdriver until it moves freely.

I kjnow this video is a ford but the mechanism is the same

Jan 18, 2016 | 2005 Toyota Corolla

2 Answers

Hood won t close


Check out the cable connection between the latch and your internal latch control. Till you locate the problem I would suggest tying down the hood with some sort of strap so it does not pop open at speed.

Apr 24, 2017 | Chevrolet Malibu Cars & Trucks

1 Answer

My 2000 ford explora wont shift into park, i have to leave it in reverse to get the key out and put the Ebrake on and shut it off. when i put the car in drive it goes all the way to the number 1, can you...


The shift linkage is out of adjustment.

The cable bolt may be loose up at the column, the column itself may be loose enough to allow it to shift position as well.

Make sure column is securely mounted, If not- tighten the 4 bolts that hold it to the dash support so it is. if it is, crawl under driver's side and on the transmission is a bracket where the cable assembly comes into it, and from there a rod that attaches on the lever on the side of the transmission. Make sure the bracket is not damaged or cracked first- if it is, replace it. There is a captive clip to release on the wide part of the piece that the bracket holds, it does not come out fully, but it will release the cable housing so you can slide it to adjust it. With the column shift in Park position, note where the rod is at the transmission. Also make note if the bracket is in line with transmission. If bracket is in line, pull the lever rearward one notch/detent that you will feel engage the lever- this moves the transmission lever to neutral, then with firm pressure push lever forward so you feel 2 distinct notches/detents forward, the lever is now in park. Push locking clip back into position once you confirm the cable outer housing is squarely seated into bracket opening and is soundly clipped into the square opening of the bracket.

If the lever will not move to that second detent or you did not feel it, you will need to check by putting the column shift to first gear position, release the connection to the lever on the transmission just to verify location of lever, and verify the lever is indeed in first gear- the lever on the transmission will move no further- then count detents forward from the rear stop. you should end up in park, and you may hear the parking pawl engage the output shaft of transmission. move lever back to the rear to the stop, reattach the connection to the cable, put column in park, release the clip again and verify the lever is as far forward as it is going to move. Push clip into lock position.

Start Explorer, with foot on brake pedal, release the emergency/parking brake and see if the vehicle moves, or if it is truly in park. It should be in park.

If you encounter some dificulty with getting the column shift lever itself moved over to park- apply brake pedal to release the park interlock mechanism.

Jan 30, 2012 | 2000 Ford Explorer

1 Answer

Gas door won't open


FIRST: try using the gas release lever from inside the car with the driver side door closed. My 2006 Jetta gas release lever would only work if the driver door were shut and I pulled the release from the inside car interior. Turns out it was a severed door wire (NOT THE RELEASE CABLE). Thus when the door was open, it stretched the damaged wire and so none of the door controls worked unless the door was closed. ie windows, trunk release, and gas release. It was a $600 repair at the dealership, parts and labor! :(

Oct 22, 2011 | 2006 Volkswagen Jetta

1 Answer

I own a 1997 e320 Mercedes. My latch wire that opens my hood was cut severing the connection to my two hood latches. My hood release lever in my car doesn't work nor my release lever in my grill. My...


only way i can think of is to remove the center grill so you can get at the mechanism but it means braking it im afraid you cannot get at it any other way

Sep 09, 2011 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

2 Answers

How do I open the hood of a Mitsubishi L300 ?


  1. Locate the interior hood-release lever under the dashboard on the driver's side of the interior of the car.

  2. 2

    Lift up and toward you on the hood release lever. The lever is connected to a cable that releases the hood. The hood will pop up about 1/2 inch when you pull the lever.

  3. 3

    Move to the front of the car and locate the exterior hood-release lever under the front of the hood. It is located near the middle of the vehicle, just beyond where the front edge of the hood meets the body. Lift up on the inner lever.

  4. 4

    Lift up on the edge of the hood while holding the inner lever in place. When the hood is up, find the hood prop and raise it, setting its tip in the hood-prop mount on the hood, to hold the hood up while you work in the engine bay.



Read more: How to Open the Hood on a Mitsubishi Endeavor ' eHow.com http://www.ehow.com/how_6301122_open-hood-mitsubishi-endeavor.html#ixzz16Ou5FhQF

Nov 26, 2010 | Mitsubishi Lancer Cars & Trucks

1 Answer

The E brakes work great but the lights stays on. It flashes when brake is applied but wont shut off when brakes are released. help please. would like to fix problem asap is a big distraction when driving...


There is a sensor under the brake lever. Try pulling up on the lever to see if the light shuts off. Most likely the cable needs some more tension so the lever does not rest on the switch/sensor causing the light to lite up.

Sep 01, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Dead battery aaa could not open the car completely shut down


Hello. If you are still locked out, I think I can help you. Above the rear license plate is a keyhole, if you have the key you can unlock your trunk/hatch from there. Then look for the manual door release lever on the driver's side above the wheel hump.

Feb 14, 2010 | 2006 Chevrolet Corvette

1 Answer

Info on do it tyour self clutch removal on 2001 mustang 3.8


REMOVAL:
  1. Lift clutch pedal to uppermost position to disengage clutch and brake pedal pivot shaft.
  2. Push clutch and brake pedal pivot shaft forward and unhook clutch release lever cable from clutch and brake pedal pivot shaft and allow it to slowly swing rearward.
  3. Raise and support vehicle.
  4. Remove clutch release lever dust shield.
  5. Disconnect clutch release lever cable from clutch release shaft.
  6. Remove retaining clip, then clutch release lever cable from flywheel housing.
  7. Remove starter motor from flywheel housing, then engine rear plate to front lower flywheel housing bolts.
  8. Remove transmission.
  9. Remove flywheel housing back just far enough to clear clutch pressure plate, then remove housing.
  10. Remove clutch release shaft from flywheel housing by pulling it through window in flywheel housing until retainer spring disengages from pivot.
  11. Remove clutch release hub and bearing from clutch release shaft.
  12. Loosen six clutch pressure plate bolts evenly to release spring tension gradually and avoid distorting clutch pressure plate. If same clutch pressure plate is to be installed, mark plate and flywheel so pressure plate can be installed in its original position.
  13. Remove clutch pressure plate and clutch disc from flywheel.
INSTALLATION:
  1. Position clutch disc and pressure plate assembly on flywheel, noting following:
    1. Three flywheel housing to block dowels on flywheel must be properly aligned with clutch pressure plate.
    2. Bent, damaged or missing flywheel housing to block dowels must be replaced.
    3. tart clutch pressure plate bolts but do not tighten.
    4. Avoid touching clutch disc face, dropping parts or contaminating parts with oil or grease.
    5. Align clutch disc using suitable alignment tool inserted in pilot bearing.
    6. To avoid clutch pressure plate distortion, alternately tighten bolts a few turns at a time, until they are all tight, then tighten to specifications.

  2. Install transmission to flywheel housing.
  3. Install engine rear plate to flywheel front lower housing bolts, then connect clutch release cable to flywheel housing and connect retaining clip.
  4. Connect clutch release lever cable to clutch release shaft, then install clutch release lever dust shield.
  5. Install starter motor.
  6. Lower vehicle, then install clutch release lever cable as follows:
    1. Lift clutch pedal to disengage clutch and brake pedal pivot shaft.
    2. Push clutch and brake pedal pivot shaft forward and hook end of clutch release lever cable over rear of clutch and brake pedal pivot shaft.

  7. Cycle clutch pedal several times to adjust clutch release lever cable

Aug 08, 2009 | 2001 Ford Mustang

1 Answer

Hood release 2004 VW Jetta


There's a hood release lever inside your Jetta by your left knee. Pull this lever to partially release the hood. Then reach your hand under the front center portion of your hood to locate the external hood release lever. pull on this lever to fully release the hood. Two (2) separate hood release levers in two different locations.

Jun 13, 2009 | 2004 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...