Question about Nissan Cars & Trucks

Open Question

Need 1997 nissan altima wiring diagram - Nissan Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: Replace 2005 Nissan altima stereo receiver

Try radio shack, or stereo sales/installation place for ready to go plug adapter. For a few bucks, it saves headaches, and butchering the wiring in case you want to re-install old one later when trading in or selling the car.

Posted on Aug 30, 2008

pal03246
  • 713 Answers

SOURCE: Need an ecu wiring diagram

what is the car doing?? by you saing "need a ECM diagram?" what is the problem with the car. that car is pretty bulletproof and I have't seen any ECM issues unless your A/C drain is clogged up and water leaked onto/into your ECM frying it up. Let me know what your symptoms are.

Posted on Sep 01, 2008

  • 13 Answers

SOURCE: need wiring diagram for 2007 nissan altima headlight

This is the service manual for a 2006 Altima - it may help.

http://rapidshare.com/files/51183743/2006-Altima.zip

Posted on Mar 05, 2009

  • 383 Answers

SOURCE: need to install a thermostat of a nissan altima

Dear Guest: If you have some reasonable mechanical aptitude, it is a simple task on this engine to do.
The thermostat is located near the front to the engine (the side closest to the belts) and on the side where the radiator is.
Follow the top radiator hose to the engine and you will have found the thermostat housing.
1. Make sure the engine is cool before doing this job.
2. Get a drain pan and drain the coolant from the radiator. The drain **** for the radiator is located at the bottom of the radiator. Some have an end which can be turned without tools and others require a flat screw driver to unscrew the fitting from the bottom of the radiator. Make sure you remove the radiator cap, as it will drain much faster. Once drained, put the drain **** back into the radiator. Be careful and DO NOT OVER TIGHTEN IT! It will snap off in the radiator!
3. Release the hose clamp which secures the hose to the thermostat housing and then grasp the hose at the neck where the clamp was and try to rotate the hose on the housing. DO NOT try to just pull the hose off. Break it loose first by rotating it on the housing. If it is stuck, get a small screw driver and carefully, slide it in between the hose and the housing, working it around until you can rotate the hose. At that point you can remove the hose and push it off to the side or take it loose at the radiator as well. CAUTION!!!!! the radiator tanks are plastic and will break if you are not careful!
4. There are 3 bolts which retain the housing to the cylinder head.
Typically the bolt head size is a 10mm. Using a 10mm socket, rotate the bolts in a counter clockwise direction, removing all three bolts. There are some that did use a 12 mm bolt head size. Most of the time the housing will just come loose. Sometimes, it will stick. If so, a light tap will break it loose. Pay attention as to how the thermostat is positioned in the cylinder head prior to removing it. Most of the time it will pop out easily or you can easily pry it out with a small screw driver. CAUTION!!!!
Do not damage the mating surface where the gasket seals.
Carefully clean the old gasket off. A single edge razor works fine.
5. The thermostat has a top and a bottom. If you look closely, you will see a place in the outer parameter of the thermostat where there is a small hole, often with a little metal tab which projects through the other side and is able to jiggle some. This is a small bleeder to help bleed the air trapped in the system when it is installed. This part of the thermostat must be at the 12:00 position.
Additionally, make sure the part with the hoop is sticking out toward you. The cylinder head has been machined to allow the thermostat to fit flush with it when installed properly.
6. Clean the old gasket from the thermostat housing. Nissan utilizes a liquid gasket sealer (silicon) which you apply a "SMALL" bead around the water inlet (the cylinder head side), let the sealer skin lightly and then put the housing in place making sure that the thermostat had remained seated during the installation. If it had come loose and you try to tighten the bolts, you will crack the thermostat housing.
7. When you tighten the thermostat housing bolts, there is a torque specification however most people don't have torque wrenches which measure in inch pounds. For those who have a torque wrench, 10mm bolts:56.4-66 inch lbs, 12mm bolts 12-14 ft lbs.
I have found that the easiest way to keep from over tightening the bolts is to grab the ratchet from the head and tighten the bolts because you don't have the leverage at that point.
8. Let the silicon dry for 10 minutes and and then fill the system back up with coolant. Reattach the hose and clamp being careful not to over tighten the hose clamp.
If you are replacing it, not more than a 50/50 mix. There is no special bleeding procedure Nissan has for this car. Just fill the radiator with coolant, turn the heater inside the car to the heat position to allow coolant flow into it as well, because it too is part of the cooling system in terms of coolant capacity. I usually fill the radiator until it shows 1/2 way up the tank. As the engine warms up,prior to the thermostat opening, more often than not, the coolant level will rise dramatically before it drops. Once the thermostats has opened top the system off, put the cap on and let it run for a while and watch for leaks. Take the car on a short loop and then recheck for leaks again. If everything has gone well, the temperature will read normal and no coolant will be leaking.
Hopefully this should be sufficient to answer your question.

Posted on Apr 05, 2009

  • 1 Answer

SOURCE: Lost Fuse Box Diagram - Altima 2005 2.5L

i need to know what ENG CONT AND ENG MTG means on the fuse box of my 2006 altima.

Posted on Jan 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Nissan Altima Stereo Wiring Diagram for Bose Navigation


None are actually color coded. The schematic has the wire colors on it next to the wire.

May 01, 2014 | 2007 Nissan Altima 3.5 Sedan

1 Answer

Need ilustration of the wiring harnes on the distributor on a 1996 nissan altima theirs 4 wires that hookup on it but the connector is busted onto pieces


Go to Autozone.com and register your car for a free wiring diagram and fusebox layout. Another site, alldatadiy.com also has diagrams.

Aug 29, 2012 | 1996 Nissan Altima

1 Answer

Need wiring diagram for Nissan Altima GXE starting system


I am sorry but fixya has no wiring diagrams of any kind. You can obtain the factory diagrams for a small fee at this site www.alldatadiy.com

Jun 28, 2012 | 1999 Nissan Altima

1 Answer

I NEED A PICTURE DIAGRAM FOR 97 ALTIMA EXAUST SYSTEM


Not exactly what you ask...hopefully these help?

http://nissan-car-parts.macautoparts.net/Exhaust-5814/515886-1997-Nissan-Altima-2-4L/ProductInfo.aspx

http://www.wheelzngrillez.com/19nialexsy.html

http://www.rockauto.com/catalog/raframecatalog.php?carcode=1210655&parttype=5836&partkey=477526&a=FRc1210655k477526-1613735

Apr 05, 2011 | Nissan Altima Cars & Trucks

1 Answer

I need the diagram for the spark plug wires from distibuter to plugs on a 95 nissan altima pls help


1995 Nissan Nissan Altima 2.4 liter DOHC L4 (KA24DE)

zjlimited_251.gif

Hope this helps (remember to rate this answer), good luck.

Mar 16, 2011 | Nissan Altima Cars & Trucks

1 Answer

Need factory wiring diagram please.


Many times the local library will have a technical section with wiring diagrams in them. Some you can even get online. Good Luck!

Jul 17, 2009 | 1999 Nissan Altima

1 Answer

Need wiring diagram for 2007 nissan altima headlight


This is the service manual for a 2006 Altima - it may help.

http://rapidshare.com/files/51183743/2006-Altima.zip

Mar 05, 2009 | 2007 Nissan Altima 3.5 Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...