Question about Cars & Trucks

1 Answer

2008 tacoma 4x4 6cyl the speedometer and the turn signals just stopped working. the tach and the hazards still work.the fuses are all good too. can you tell me what it could be?

Forgot about the fuses behind the coin holder on the left side under the steering wheel. it was a 10amp fuse that connects the a/c,turn lights,speedo. replaced it and all is good

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,309 Answers

Www.tacomaworld.com

Posted on May 09, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Buick rendezvous turn signal, and brake lights, and hazards lights stop working


Check the HZDLFL fuse# 40 - 15amp in the console fuse block
Fuse Block - Center Console
Inside of console, behind the right console access panel , if the fuse is good the turn signal / hazard flasher module is bad.
Turn Signal/Multifunction Flasher Module
In the fuse block - center console

Dec 05, 2015 | Buick Cars & Trucks

1 Answer

Turn signal hazard lights not work


wiggle fuses and connection wires

Sep 27, 2013 | 1996 Chrysler LHS

1 Answer

Turn signal hazard lights work but not running lights


The parking lights should be on a different circuit from turn signals - hazard lights. The bulbs usually have two filaments, one for each circuit.
On most models there is a tail light fuse and relay that handles front and rear parking lights.

Jun 28, 2013 | Toyota Tacoma Cars & Trucks

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

1 Answer

Hazard light button pushed thru housing. Can't turn off hazard lights


REMOVE HAZARD FUSE IT WILL TURN OFF FLASHER UNTIL YOU FIX HAZARD BUTTON.
YOU GOING HAVE TO REMOVE SPEEDOMETER AND TACH CLUSTER TO GET TO HAZARD SWITCH.TURN OFF RADIO FIRST BEFORE REMOVING NEGATIVE BATTERY CABLE BECAUSE YOU WILL DISABLE AIRBAGS WHILE WORKING AROUND STEERING WHEEL AND DASH AREA. WAIT 20 MINUTES BEFORE WORKING AROUND DASH AREA AFTER DISCONNECTING NEGATIVE BATTERY CABLE.

Jan 13, 2011 | 1999 Oldsmobile Alero

1 Answer

Speedometer turn signal short 94 c1500


First I would go back and check out the turn signal switch to make sure you install that correctly. Look for shorts or wires that could be grounding out. Go to the library and getting a wiring diagram and find out everything that goes to that fuse. Also if the truck is rusty check all the body grounds. Good luck.

Jun 04, 2010 | 1993 Chevrolet S-10

1 Answer

Electrical


Check the alternator out put,check it at the battery,with the headlights on,and the ac on high blower,the volts should read 13.65 volts to 14.25 volts,no lower,if it is replace the alternator.

May 28, 2010 | 2000 Subaru Outback

2 Answers

Speedometer/tach stopped working


There are 2 sensors on the engine that sent a signal to the computor and speedometer and tach. When one of these goes bad it can make the speedometer and tach go all over the place and also just stop working. This can also cause all types of engine running problems because the information being sent to the PCM will be incorrect all so. The units are easy to replace once you find them, it seems that they are located in different areas of the engine with each year the vehicle was put out.

Feb 24, 2009 | 2002 Dodge Neon

1 Answer

1991 Maxima Turn Signals


the flasher unit controls both hazards and indication you will need to remove the shroud around the steering wheel and follow the wires coming off the indicator stalk down until you find the problem there should be some majour plugs on the stearing collum check thaat these are conected and work from there

Nov 30, 2008 | 1991 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...