Question about Cars & Trucks

Open Question

Have a 2008 equinox and both brake lights are out. I hear a clicking in the fuse box when i press on the brake. Fuse and bulbs are fine. Clicking coming from fuse box in car

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: headlights flicker all the time

Hi, my name is ricky and im 24 yrs old and from Bronx, N.Y . I bought my 03 impala in 04 and i had the same problem in 2007 in which that clicking noise happens. The headlights flicker, and even the gauges inside the car would flicker at times. It has nothing to do with fuses or a relay, please dont spend money on that b.s. like i did..lol I will try my best to explain what i did so that you can save some money and time. READ EVERYTHING AND USE ADVICE AT YOUR OWN RISK.
1st of all - I went to a junk yard/auto salvage yard to find a USED part that i needed. Often there are good parts from cars that have been totalled.
2nd- What i asked for was a Body Control Module. This controls most of the electric issues you are having and costed me about 50 dollars compared to a new one that was over $200 and reached up to $500.
3rd- I went head first under the steering column and found where the BCM was located. Poke around to find it cause it is def. there, hidden well. It doesnt take special skill to remove it or find it.
4th-Replace the BCM, but be advised that after you do this, your car might not crank over.My car did crank over because i installed a automatic starter previously so i could have started it with the remote start.
5th- you MUST take the car to a chevy shop so they can Program your car to the body control module this costed me about $250.
All together this information has to help you in someway.
If you have further questions or would like to make a comment, then e-mail me at " gyalflexfameh@gmail.com "
I hope this helps...im not saying it is a 100 percent guarantee for you, but i had this same problem recently and this was the answer to my problem. By the way, never buy a american car again or a GM product for that matter...Kudos

Posted on Dec 19, 2008

motor1258
  • 6674 Answers

SOURCE: 2005 Dodge Durango, clicking noise coming from the

ASD relay faulty? Try swapping it with same number from other relays & see if clicking stops. I believe there is others same # in there, but might not be. Get back to me if not.

Posted on Jul 18, 2009

  • 1986 Answers

SOURCE: brake lights don't come on. checked fuse box,

look up above your brake pedal and you will see the switch.. It will either between the firewall and the pedal arm (switch moves in when you brake).. Or it will be between the pedal arm and the dash (switch moves out when you brake)

Posted on Oct 08, 2009

redds55
  • 2620 Answers

SOURCE: 2003 Chevy S10 Brake lights

OK try this, push and hold brake then push on the hazard switch if brake lights come on then replace the turn signal switch.

Posted on May 14, 2011

gregjr_pl1
  • 138 Answers

SOURCE: 2005 Ford Escape won't start but hear a

This sound is the relay, Is the battery new if more than 1 and 1/2 yrs. you need to replace your battery.
Is your engine cranking when start, if not, the battery need to be replace.

Posted on Oct 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is on 1987 pontiac 6000 are the bulbs for turn signals How do I get to them? & or the flasher ? Is it in the fuse box?


The turn signals at the rear share the same bulb, same filament on the bulb even, as the brake lights. So if you have brake lights, the rear turn signal bulbs are good. If I recall, you access the rear bulbs from inside the trunk, and pretty easy to change bulbs. Look for a panel or trim piece in the trunk that covers the light bulb assemblies. You turn the bulb sockets a quarter turn counter-clockwise and pull them out, then you can replace the bulbs. They are two filament bulbs-one filament for the park lights (tail lights) and one filament that serves for brakes and turn signals together.
The flasher unit is a small round cylinder, I don't believe it was in the fuse box, but located up under the dash, close to the steering column. The hazard flasher unit was also up under there and looks the same. Look for them on a bracket near or by the steering column, possibly one on each side of the steering column To find the turn flasher, turn your hazard switch on. The little round unit that is clicking-you may hear it or feel it click with your finger on it-is the hazard flasher. The turn flasher will be the one that is not clicking. A little round cylinder is how you identify it.

Jun 03, 2014 | Cars & Trucks

1 Answer

Trailer brake harness has no brake lights, and fuses are fine


you have to replace the flasher combination unit behind drivers side under dash fuse box. it is located on drivers side door well in the left side of the dash. to get to the module you will need to drop the underdash cover to access the back of the fuse box. You should see a black box. if you put on the hazard light you should hear where the clicking noise is coming from and that should make locating it easier. Once you locate it simply pry it off the box and insert new part. then presto you should have brake lights again. good luck

Oct 01, 2011 | 2005 GMC Sierra

1 Answer

I have a 2004 Scion xB and my right rear signal light isn't working. It's not the bulb because that's working and the click sound sounds off but it wont light up in the dashboard. My left signal light is...


the light in th DASH-BOARD IS out, if you hear clicking & outside is click-g,theres not a fuse,for signals, there is a flasher-relay chk under dash or by th kick-panel or next to FUSE-CLUSTER(BOX), HOPE this helps, good-luck...

May 04, 2011 | 2004 Scion xB

4 Answers

Brake lights do not turn on at all? Is there a fuse (where and which one)?


Thanks for choosing FixYa and welcome to the site. Check your bulbs and fuse first. The fuse is in your fuse box and it should be labeled, such as tail lamp possibly. If the fuse and the bulbs are good, you probably need to change the brake switch. It is located right above your brake pedal. You may want to try to mess with the release button because sometimes they get stuck. If it is not, change the whole switch. It cost about 20 dollars. It is a round chrome looking cylinder more then likely. If you have any questions, feel free to ask. Thanks for using FixYa and have a good day. For the fuse, check under your hood.

Apr 01, 2011 | 2008 Chrysler Aspen

1 Answer

2008 jeep liberty brake lights don't work. all other lights do. bulbs are good.


check fuse for brake lights. You can find this info in the user manual were the fuse is located in the fuse box.

Mar 18, 2011 | 2008 Jeep Liberty

1 Answer

My brake lights were not working so we checked all of the fuses, now we tried to crank the car and it wont start but you can hear a click from around the fuse box under the hood. car was working fine...


When you checked the fuses did you pull them out and examined them and if so was the batter connected. You could have accidentally blow a fuse by pushing it back into the fuse socket. Re-check all the fuses again but this time disconnect the battery. Any broke fuse replace and once done re-connect the batter.

As for your brake lights check the brake pedal and make sure that upon depressing the brake pad you hear a clicking sound engaging a switch to operate the brake lights. Good Luck

Jan 07, 2011 | 1998 Ford Contour

2 Answers

Need to know which fuse control my brake lights. Light bulbs are fine but when i press the brakes the lights dont come on.


change the brake light fuses on ur chrysler 300. also get it checked at a dealer to spot any other issue, if any.

Dec 22, 2010 | 2008 Chrysler Aspen

2 Answers

My brake lights wont work,i checked all the fuses,bought new bulbs,and bought a brake switch,and still nothing.my regular lights come on,just my brake lights dont work.dont no if this is part of the...


Just had a similar problem. Brake (stop) lights and horn didn't work. Couldn't find mention of stop lights in fuse chart. Found horn fuse to be slot 21 in the engine fuse block (not the fuse block in car interior). Replaced 15A fuse and all now ok.

Aug 21, 2009 | 2005 Mazda 3

1 Answer

Both 2003 oddyssey brake lights dont work High


clean bulbs socket out using the electronic spray cleaner for electrical connectors.

May 13, 2009 | 2003 Honda Odyssey

1 Answer

Blinkers


If you can turn the blinker on left or right and the light comes on but doesn't blink......Open the drivers door, there is a fuse box, On the side of the dash.. The relay willl be a small silver canister looking relay in with the fuses.. put your finger on it and turn the blinker on.. you should feel and hear a click...( With the key in the on position ).. That is what needed replaced if it doesn't keep clicking...Thats the turn signal relay... What makes it blink.......Hope this helps..
Please rate this solution if it helps... Thank You.....

Nov 04, 2008 | 1996 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...