Question about Cars & Trucks

Open Question

Where is the high pressure and low pressure lines leaving the power steering pump 2010 hemi charger

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 69 Answers

SOURCE: power steering line leak for 93' taurus lx at pump

did the hose get cracked or crimped when it was replaced may need new hose

Posted on Oct 06, 2008

chuck943
  • 783 Answers

SOURCE: high pressure power steering hose - one or two?

Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump

Posted on Feb 23, 2009

  • 1596 Answers

SOURCE: high pressure power steering hose on a 1995 surburban

PUMP R&R PROCEDURE at Bottom


Do I need to pull the power steering pump off of the 1995 surbuban 350 engine in order to replace the high pressure hose?<-You Ask.

NO Not on the 95 and If you do need or want to REMOVE the PUMP it Comes off Without the Removal of P/S Pump Pulley. Now if you are replacing the P/S Unit Yhere is A Special tool fo pull off Pulley .
Ist a Universal tool for Ford & GM just P/S Pump Pulley Removal Tool Auto Zone has en for $40.00 or rent it from them.

POWRE STEERING PUMP R&R

Removal/Installation Notes

  1. Disconnect hoses at power steering pump, then plug pump ports and hoses to prevent dirt entry.
  2. Loosen pump adjusting bolt and remove pump drive belt.
  3. Remove pump to support bracket retaining bolts, then the pump.
  4. Reverse procedure to install.

Posted on Mar 22, 2009

csmock132
  • 4669 Answers

SOURCE: power steering

Go to a parts store and tell them you want power steering return hose or transmission cooler hose. It comes in bulk, they can just cut off how much you need.

Posted on Mar 25, 2009

  • 14036 Answers

SOURCE: subaru impreza 1993 power steering leak

YOU CANT USE A REGULAR FUEL LINE ON POWER STEERING AS A HIGH PRESSURE HOSE.BECAUSE POWER STEERING PRESSURE IS 1000 PSI.YOU HAVE TO BUY THE POWER STEERING HIGH PRESSURE HOSE IT HAS NUMBER OF PLIES MATERIAL WEAVES TO MAKE IT STRONG.IT WAS MADE FOR POWER STEERING HIGH PRESSURE.YOU DONT HAVE A BLOCKAGE .THE HIGH PRESSURE HOSE JUST WORE OUT.REPLACE IT .IT SHOULD FIX THE PROBLEM.

Posted on Sep 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change powerstering pump chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Dec 13, 2012 | 2008 Chevrolet Uplander

1 Answer

I have a 2010 dodge hemi an the AC wasn't blowing


Is the compressor running ? What are the low and high pressure readings ?
Are the radiator fans running ?
Is one ac line cold and one hot in the engine compartment.

Jul 30, 2012 | Cars & Trucks

2 Answers

Replace power steering pump on 06 chevy uplander


I just finished replacing mine.

It is much easier if you do these steps:

1. Remove the serpentine belt.
2. Remove the nuts holding the main fuse box over the battery.
3. Remove the reinforcing bar over the battery.
4. Remove the battery.
5. Remove the windsheild washer tank.
6. Now you have access to remove the pump pulley. Without removing the stuff, it may be possible, but it will be extremely difficult.
7. Remove the pump pulley.
8. Loosen the high pressure hose fitting.
9. Remove the return line clamp.
10. Remove the power steering pump mounting bolts.
11. Remove the high pressure hose fitting.
12. Remove the power steering pump while sliding off the low pressure hose.
13. Remove the clips holding the reservoir on the pump.
14. Remove the reservoir.
15. Install new o-ring on the reservoir.
16. Install reservoir on new pump.
17. Install clips to hold reservoir on pump.
18. Install new o-ring on high pressure fitting.
19. Place new pump in position while sliding on low pressure hose.
20. Loosely attache high pressure fitting.
21. Tighten pump to mounts.
22. Tighten high pressure fitting.
23. Install clamp on low pressure hose.
24. Install power steering pulley.
25. Install washer reservoir.
26. Install battery.
27. Install reinforcing cross member.
28. Install fuse panel.
29. Install serpentine belt.
30. Bleed the power steering system.

Jul 08, 2012 | 2006 Chevrolet Uplander

1 Answer

Power steering fluid is leaking badly. How do I locate the power steering pump and check the lines


Toyota power steering hoses fail very often, not certain what model you have, but follow the hose back from the power steering resiviour,and you will find the pump, then there is a high and low pressure line leading to the steering rack at the rear of the motor, it is usually the high pressure hose that fails

Aug 08, 2011 | Toyota Camry Cars & Trucks

1 Answer

On a 99 Olds Alero, in the return lines of the power steering hoses, which place does the high pressure hose attach to?


RETURN TURN LINE GOES TO THE LEFT OF RACK PINION AND HIGH PRESSURE HOSE GOES TO THE RIGHT OF RACK PINION.LOOKING AT POWER STEERING PUMP HIGH PRESSURE HOSE THICK HOSE SCREWS INTO POWER STEERING PUMP.WHILE LOW PRESSURE HOSE HAS A HOSE WITH A CLAMP THE LOW PRESSURE HOSE HOOKS TO TOP OF POWER STEERING PUMP.LOW PRESSURE DONT SCREW INTO POWER STEERING PUMP IT IS HELD IN PLACE BY A HOSE SMALL CLAMP.

Jun 24, 2011 | 1999 Oldsmobile Alero

1 Answer

How to install a power steering high pressure line on a 1998 olds 88 regency


Hi,
You will need line wrenches to get the line off the steering gear assembly (tight in there near the frame sub assembly) First you will want to remove the drive belt from the power steering pump. Then remove the bolts from pump to bracket and lift pump up. On back of pump, remove low pressure line and drain fluid into a container. Under pump, remove high pressure line, and push it downward toward floor. From under car, follow the line to the steering gear, ( the line may have a keeper clamp or two for stationary support to remove along the way) then detach. Installation is reverse of disassembly........Not fun, but doable.....Mike

Jun 22, 2011 | 1998 Oldsmobile 88

1 Answer

Power steering fluid pours out when i crank the car


When you crank the engine, it rotates the pulley on the power steering pump. As the pump spins the fluid passes through the pump, rack and pinion and the high and low pressure lines. The high pressure lines are usually the culprit. The high pressure line can be identified as a metal line going into a rubber hose off of the power steering pump. Have someone crank the engine as you trace the leak. Be sure to wear safety equipment, like safety glasses and gloves to protect yourself from any squirting fluid.

Dec 13, 2010 | 1992 Honda Accord

1 Answer

How do i change the power steering pressure switch on my 04 dodge ram 1500 hemi? I can't find it.


From the Factory Service Manual, you can get one relatively cheap from www.promanuals.net. Here is a link to your 2004 Dodge Ram Service Manual.

The power steering pressure switch is installed in
the power steering high-pressure hose (Fig. 9).

(1) Disconnect electrical connector from power
steering pressure switch.
(2) Place a small container or shop towel beneath
switch to collect any excess fluid.
(3) Remove switch. Use back-up wrench on power
steering line to prevent line bending.

1425db0.jpg

Oct 02, 2009 | 2004 Dodge Ram 1500

2 Answers

2001 jetta Power steering fluid leak


A power steering system has a rack,fluid tank with hose to pump,pump,high pressure in hose and a low pressure return hose to tank. I f you say theres no leak at the rack that only leaves those other conponents. I would check the pump its self and the high pressure hose where it leaves the pump. It may also be leaking at the tank, where the hose leaves to the pump because it is only fastend down with clips and they can come loose or the hose can split. hope this helps

Jun 03, 2009 | 1996 Volkswagen Jetta

1 Answer

Power steering pump connections high and low pressure outputs


top rear most line comes from the pressure regulator, rear side outlet at angle line goes to oil cooler then to fluid reservoir. Smallest of all three lines is a pressure line that goes to the rear self leveling system.

Jun 16, 2008 | 2006 BMW 750Li

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...