Question about Dodge Cars & Trucks

1 Answer

Dodge neon tire leans in

I replaced my wheel bearing a month ago but the tire still leans inward. and now it leans so bad the tire is against the strut. im wondering if my strut is damaged or shot because the bottom of it has rust holes.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 2,534 Answers

Yes, Brad, you have a severe problem.
Please try not to drive the car at all until the assembly ( all the defective pieces) are replaced, or you will likely have that wheel fall off really soon.
If it were me, I would not even drive it to a repair shop, I would have it towed.
God bless your efforts.

Posted on May 08, 2017

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 dodge caliber rt slap stick put new tires on 3 months ago driver side front tire is worn cant let off wheel car pulls bad to the right side of the road


The popping could be from a bad CV axle joint, or a bad wheel bearing. Better get checked, sounds very worn. Raise the wheel on a jack and watch for play. Grab wheel at 3 and 9 o'clock, and shake back and forth-watch for play. Wheel bearing? CV joint -is boot still good? Ball joints at bottom of wheel attaching point to the control arm-check this for play, too.

Apr 11, 2017 | Dodge Caliber Cars & Trucks

2 Answers

2002 dodge neon left rear wheel looks crookd and vibrating. just had shcocks alignment and stabilzers changed and still looks crooked


When you had the alignment done the place should have given you a printout of the changes. The mechanics might not have done a 4 alignment. At any rate if it is making noise it is most likely a bearing that is bad.

Mar 25, 2015 | 2002 Dodge Neon

1 Answer

2004 chevy venture van front left side tire is


Check the front wheel bearing. jack the vehicle up, grab the tyre and check for movement of the wheel hub while the steering is locked. Any excess movement will cause the issue.

Oct 16, 2014 | Cars & Trucks

2 Answers

Burning plastic smell from drivers side rear wheel


pull off wheel and check brake pads low,caliper sticking ,or debris -if brakes look good than check hub-wheel bearing----- may be going bad

Apr 11, 2014 | 2005 Honda Accord

1 Answer

Wheel bearing


This is usually a balljoint problem. Although you can try lifting the wheel off the ground and pulling the top of the tire, some put a bar on the ground just under the tire and lift up.
With a 4x4 there is extra hardware which may interfere with wheel travel during this test. The idea is there is a knee action which the balljoint pivots on. Over or under jacking can mask the travel or slop in the joint, so try testing from different jacking heights.
Now a wheel bearing can cause this problem if it is bad enough. If this is a 4x4 the hub bearing is more substantial.

May 04, 2013 | 1986 Ford Ranger 2WD

1 Answer

Front passenger wheel leaning on 98 expedition


This is most likely a ball joint problem. If you can, jack that tire up in the air and see if you can move the whole tire in and out from the top. Try to see if there is movement in the ball joints while you move the tire. If that is not the problem, it could be a wheel bearing, but i would check the ball joints first. Hope this helps.

Feb 23, 2013 | 1998 Ford Expedition

1 Answer

Tire leaning inward and steerling wheel cocked


probably a tie rod end issue, and you definitely need an alignment bad. sounds like you might have bent something as well

Jan 26, 2012 | 1990 Chrysler New Yorker

2 Answers

2002 Neon, constantly replacing rear wheel bearings. Why?


are hte wheels aligned this can cause pressure on the wheel bearings are they being put on to tight this will also cause this how about grease

Feb 09, 2011 | Dodge Neon Cars & Trucks

1 Answer

Why does my neon make a loud noise id rive, after


From your description it certainly sounds like a bearing but since you've changed it I would look at the tire for any chopping or cupping as this will cause a noise that is speed related as well. To verify a wheel bearing as you drive the car carefully weave from one side of the lane to the other. A wheel bearing will change pitch as you change the load on it and usually the bearing that is quiet to the left is the right bearing that is bad and vise versa.

Jun 04, 2010 | 2000 Dodge Neon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...