Question about Cars & Trucks

Open Question

Garmin Nuvi 1340 will not charge in car.

It is ok connected to computer. When in car, it switches on with ignition, but will not switch off. Car charger and battery have been replaced

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 58 Answers

SOURCE: ford mustang 1966 ignition problem.

The starter solinoid is bad.Clean and check battery cables also.

Posted on Jun 21, 2008

leetamara
  • 702 Answers

SOURCE: ford taurus 1996

Place key in ign. lock n tumbler and turn to "on" position. Under the column you'll see a small hole to put a small screwdriver or rod into and press it in. While you're pressing it, pull the lock n tumbler out. Installation is the reverse of removal but without the use of the rod. Just push the lock n tumbler in the hole and turn key to lock position and pull key out.

Posted on Jul 28, 2008

  • 2 Answers

SOURCE: 1996 grand am ignition switch will not turn

I had this same problem. You will need to replace the ignition cylinder and this can only be purchased from Pontiac ($245). The problem is actually the key release button, its sticking. There is a small button under the steering wheel that you can only see if you take the steering wheel cover off. If you get that fixed you shouldnt have any problems

Posted on Mar 02, 2009

  • 24 Answers

SOURCE: 1996 audi a4 ignition kill switch wont recognise car keys

HI,MARK,THE SIGNAL FROM YOUR KEY IS NOT GETTING TO YOUR IMMOBILIZER.THE PROBLEM IS MORE LIKELY AT THE PLUG ON THE READER COIL ON THE IGNITION.YOU WILL HAVE TO BEND THOSE TERMINALS SLIGHTLY CLOSED AND INSULATE THE WIRES SEPERATELY.THIS FEATURE IS PART OF THE VEHICLES SYSTEM UNFORTUNATELY,ANDY

Posted on Mar 19, 2009

SOURCE: Charging problem.. Wont charge battery

The instructions for installing a new alternator usually read to fully charge the battery (12.3 - 12.8 volt range). Otherwise, the alternator will be damaged when it initializes. I have seen some extreme damage result from installing a new alternator with a low-charge battery. The torque required to turn an alternator when damaged in this scenario is unbelieveable!

Posted on May 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car has no power


the battery must be flat , try a jump start or get a new battery , when you have got engine running get the alternator charge rate checked as could be the reason for flat battery, if charge rate is ok then check to see if anything had been left on whilst car was left

Jul 11, 2014 | 2000 Hyundai Elantra

1 Answer

I have a 98 olds intrigue and I just replaced tha ignition switch now car won't start wht should I do now to get the car to start


check all of the connections at the switch if connections are ok and no wires are pushed out check you ignition fuses

Jul 07, 2012 | Cars & Trucks

2 Answers

Ford focus dashboard flashing and no starting it


try starter or your ignition relay switch or check fuses

Feb 04, 2012 | 2006 Ford Focus

1 Answer

IS THERE A FUSE FOR THE ECU ON A 92 EAGLE TALON


I don't think so. I got a 95 and I've done all kinds of electrical checking for various things and to my knowledge there isn't. There's fuses for the ignition and engine along with other electrical items but no specific computer fuse that would turn off a computer. I assume the car won't start?

If your car is simply not starting it could be something as simple as the neutral safety switch if you only hear a click turning the key. Disconnect under left side dash. White and has a green and black wire coming from button behind clutch pedal.

If car cranks but just wont start then could be numerous things. Check the 30 and 40 amp fuses under hood. Make sure battery terminals are connected tight and clean with brush tool if needed. If battery is fine and charged, I assume you have checked, then I'd focus on the ignition system.

ignition switch (in steering column)
neutral safety switch (disconnect above pedal)
starter relay (under radio)
starter solenoid
starter

If cranks then neutral, ignition and relay switches are fine
If clicks then ignition and relay fine but neutral switch or solenoid may be bad

Jan 26, 2010 | 1992 Eagle Talon

2 Answers

Driving along and the car just stops. enough


You mite have an ignition module problem but it sounds like your fuel pump is not working. Have some one turn the ignition on as you listen for the pump switching on

Oct 10, 2009 | 2003 Pontiac Grand Am

1 Answer

Took baterry out to charge


The mechanic should check the ignition switch of the car . prepare the equipment to be used then check the ignition switch, check the wires that are connected to the ignition switch that connect to the battery. you also have to check the fuse if the ignition switch is worn out or destroyed then repair or replace.The wires if there are worn out or destroyed wires and fuses then replace , if loose wire connection then reconnect them.But to figure it out the problem is only in the ignition switch and its wires or wire connections.You just have to repair and reconnect the wires and repair the ignition switch.

Sep 15, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

Car not charging. ignition switch? altenator?


It is a bad alternator. ignition switch has nothing to do with the charging system.

Aug 04, 2009 | 1994 Mercury Cougar

1 Answer

New ignition switch now car security system locked


ok here you go
make sure the battery is fully charged befor starting
turn ignition to run
attempt to start once then release the key in the run position
let vehicle sit with the key on for ten minutes
the security light should turn off
turn igniton switch off
wait 5 seconds
turn key to run position
let vehicle sit for 10 minutes
turn key off
wait 5 seconds
turn key to run position
let vehicle sit for ten minutes
turn key off
wait more than 6 seconds
and start engine

Jun 14, 2009 | 2001 Chevrolet Monte Carlo

1 Answer

Won't start


You should check the ignition switch it sounds like there maybe a connection issue

Dec 08, 2008 | 1997 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...