Question about 2002 Isuzu Axiom

2 Answers

Replace third tail light bulb

How do you get to the third light bulb in order to replace a burnt out bulb

I also have a problem with the transmission shifting in and out of second to third gear and in and out of overdrive. The fluid is full, I am not driving the car hard at all. Do I need a rebuild? How much does this usually run? Thank you - Robert L. Acworth Ga

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 138 Answers

Check vacuum hoses to tranny for leaks or just change if not sure. Tranny repairs $1000 and up.

Posted on Jul 25, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 499 Answers

To replace the rear taillamp bulb in an 2002 Isuzu Axioum:
1. Open the rear tailgate.
2. Remove the two screws that hold the tail lense asembly in place.
3. Now there are two pins that hold the lamp in place you must use a screwdriver or other flat device and lightly pry the lense out to the right or left of the vehicle depending on which side your are working on. If you pull back it will not come out as you are putting pressure against the pins it must be pulled toward the side that the vehicle you are trying to remove the lense on.
example: changing the right lamp. {} denotes the lense and the diagram we are looking from the back of the vehicle
{}_____{} -->Pry this direction.

Posted on Jul 25, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace dodge stratus brake lights


Inside trunk, remove two black plastic nuts holding carpet liner in place on side where bulb is burnt out. Pull back carpet. Use a flat screwdriver to pop out the wiring. Remove three nuts using a small open-ended socket or pliers. Pop out entire tail light assembly. Locate bulb to be replaced. Rotate 1/4 turn to remove from socket. Replace bulb and repeat in reverse order to reinstall. hopefully that helps :)

Read more: http://wiki.answers.com/Q/How_change_a_brake_light_bulb_for_a_dodge_stratus_2001#ixzz1xGPgnkfB

Jun 09, 2012 | 2005 Dodge Stratus Sedan

3 Answers

Rapid right turn signal on dash but no right rear turn ligt at all


What that rapid turn signal on the dash means is, the rear turn signal tail light is burnt out. This is how you know the bulb is bad. Replace the burnt out tail light bulb and you will be back to normal.

Jan 16, 2011 | 2008 Chevrolet Impala

1 Answer

Change out a taillight


You want to change the tail light bulb?

The process for replacing tail light bulbs is the same in all models. If you have a burnt-out tail light bulb, you may need to replace the brake light, the reverse light or the turn signal. The procedure to replace each of the bulbs is the same.



    Instructions

    1. Open the Hummer's rear swing gate. This will expose the edge of the vehicle's tail light assembly. You'll see two small Phillips head screws that hold the tail light assembly in place. Put on your gloves.

    2. Remove the two screws from the tail light assembly. Pull the tail light out and inspect the back for two bulbs. The top bulb is the brake light and turn signal. The bottom bulb is the reverse bulb. Determine which bulb you need to replace.

    3Rotate the bulb's socket counterclockwise to disconnect it. Unplug the bulb from its socket.

    4Push the replacement bulb into its socket firmly. Insert the socket back into the tail light. Turn it clockwise to secure it in place.

    5Place the tail light into its cradle. Hold it with one hand and replace the Phillips head screws with the other.

Dec 03, 2010 | 2008 Hummer H3

1 Answer

When I press the break only my passanger side tail light works. Is this a fuse problem?


Try replacing the passenger side tail light bulb.
Inside trunk, remove two black plastic nuts holding carpet liner in place on side where bulb is burnt out.
Pull back carpet, use a flat screwdriver to pop out the wiring. Remove three nuts using a small open-ended socket or pliers.
Pop out entire tail light assembly. Locate bulb to be replaced. Rotate 1/4 turn to remove from socket. Replace bulb and repeat in reverse order to reinstall.
Thank you for using fixya and good luck

Apr 29, 2010 | 2004 Dodge Stratus

1 Answer

How do i replace the tail light bulb?


to replace the GM tail light bulb, you will drop down the tail gate and you will notice 2 screws on the tail light assembly, you will remove those 2 screws with the proper screw driver, once you do that the whole tail light assembly will come off, then you will see onother 2 screws holding the light panel to the tail light assembly, or brackets holding the light panel to the tail light assembly remove either or and you will have access to the three bulbs on that light panel, replace the burnt one and follow the same intrunctions to put back.

Apr 06, 2010 | 2005 GMC Canyon

2 Answers

No brake lights 1990 ford f 150


First, check fuses. If the fuse for tail and brake lights is OK, check the bulbs. If they are OK, you need a new brake light switch, which attached to the brake pedal under the dash. The part should be less than $20. These are a common replacement item on older fords.

Dec 20, 2009 | 1990 Ford F150

1 Answer

Brake light is out on my 2000 Audi A4. Do i need to replace the whole assembly or can i just replace bulb?


remove the bulb thats out, check the socket it's in for burnt contacts as this is common. if the contacts are burnt check the metal contacts on the tail light assembly, if they are burnt you will have to replace the whole assembly. if they are ok replace the bulb and socket

Nov 17, 2009 | 2000 Audi A4

Not finding what you are looking for?
2002 Isuzu Axiom Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...