Question about Toyota Cars & Trucks

1 Answer

Rear air conditioning stopped working on a 2003 toyota sequoia?

Posted by on

  • Nikki Gold May 08, 2017

    Ok I will check thank you Robert Garcia

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 874 Answers

First check for burned rear blower fuse , if good check the blower motor for brushles empty

Posted on May 08, 2017

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

harley9701ha
  • 424 Answers

SOURCE: Rear Air Conditioning

Check under the right side of the vehicle. look for green oil near right rear wheel area. sometimes the lines rub and start leaking. will have to replace lines if that is the case.

Posted on May 29, 2009

  • 1861 Answers

SOURCE: 2003 toyota sequoia radio error code 1.will not

Error one indicates a bad laser pickup, or a calibration issue. I would recommend a CD cleaner, but, if that does not help, the radio will need to be taken to an authorized service center. The 01 code is rather common to those radios.

Posted on Oct 09, 2009

  • 13 Answers

SOURCE: 2003 toyota sequoia rear door latch broken

First, take off the license plate2_bing.gif.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.

Posted on Dec 12, 2009

  • 1 Answer

SOURCE: my Acura 2003 TL 3.2 stop working all both system

it is probably the blower motor resistor, had the same problem on 2003 CL Type s, the fans for the A/C and heat just stopped working was the symptom . The part is only about 70 dollars.

Posted on May 21, 2010

  • 977 Answers

SOURCE: My 2003 Toyota Sequoia rear window will no longer

I don't think that there would be a fuse for each window, it could be a wiring problem check the wires on the window switch that isn't working to make sure the problem isn't there also check the wires on the window motor, if you have a test light you may be able to trace where the power is getting to before you replace the window motor,if the power is getting to the window motor you would have to assume the window motor is faulty.....hope this helps......cheers.

Posted on Sep 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The climate control unit stopped working


Ummm.. blown fuse? That would be *my* first stop.

Dec 08, 2015 | 2001 Toyota Sequoia

1 Answer

Air conditioning poor


The air condition unit may need re-gassing with refrigerant gas.

Jan 07, 2013 | 2003 Toyota Sequoia

1 Answer

Just bought 2003 Toyota Sequoia and find that the brakes are very spongy feeling. Traveling at 45, I pushed on the brakes with about 80% of my strength and still couldn't feel them bite. Two different...


Hi. To answer your question, No. The Sequoia has great braking ability, assuming that the brakes have been maintained. Most likely, your rear brake shoes may not be adjusted properly, and that means that the rear brakes are not doing their share of the work. Try this: Put the park brake on, and then drop the trans into drive, and give it a bit of gas. If the vehicle moves at all, the rear brakes need adjusting. This is a very common problem.

Jul 11, 2009 | 2003 Toyota Sequoia

2 Answers

My rear hatch door handle broke i need to replace it. how do i replace it?


how do i get the rear gate panel off so I can replace the latch on the 2003 sequoia.

Jul 06, 2009 | 2002 Toyota Sequoia

2 Answers

Rear door latch replacement 2003 sequoia


Fig. The latch bracket shown is moved by loosening the mounting fasteners and sliding it as necessary. Matchmark the bracket to the door pillar before moving-1.8L Passat model shown

Jun 02, 2009 | 2003 Toyota Sequoia

1 Answer

2003 Toyota Sequoia won't start.


Have you gotten this problem fixed yet? If not what is the condition of the battery cables( corrosion free)? Also how old is the battery? One dead cell could possibly cause this problem.

Feb 03, 2009 | 2004 Toyota Sequoia

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...