Question about Hyundai Cars & Trucks

Open Question

2004 Hyundai santafe 3.5 ignition wiring diagram

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 625 Answers

SOURCE: O2 sensor wiring diagram for 2004 hyundai sonata

there is two wires then suposed to be same color they are not what you looking for but if you have a grey and a black wires it willl be one of those i hope and this help

Posted on Jun 20, 2008

jpk528
  • 95 Answers

SOURCE: 04 sonata stereo wireing diagram

Battery ORANGE (+) RADIO HARNESS
Accesory YELLOW (+) RADIO HARNESS
Ground BLACK (-) RADIO HARNESS
LF Speaker (+) BROWN/WHITE
LF Speaker (-) BLACK/WHITE
RF Speaker (+) BROWN/YELLOW
RF Speaker (-) BLACK/YELLOW
LR Speaker (+) BROWN/RED
LR Speaker (-) BLACK/RED
RR Speaker (+) BROWN/WHITE
RR Speaker (-) BLACK/WHITE

Posted on Feb 20, 2009

  • 1 Answer

SOURCE: 2001 Hyundai SantaFe-wiring diagram

how I find the a/c diode for santa fe hyundai 2001

Posted on Jun 07, 2009

  • 1584 Answers

SOURCE: I have an hyundai santafe 2004 I do not have a

Purchase another from your Hyundai dealer, You will need to take vehicle in to get key barrel number read and to reset new remote to your vehicle.

Posted on Dec 03, 2009

ghost45
  • 1280 Answers

SOURCE: hyundai santafe 2004 how to fix p0456...or what

Here's the procedure:

Purge Control Solenoid Valve (PCSV) Line Inspection
1. Ignition "OFF".
2. Disconnect the hose leading from the PCSV to the intake manifold at PCSV.
3. Using a vacuum pump, apply specified vacuum(Approx. 15 in, Hg) to the manifold side of the valve and verify PCSV holds vacuum.
4. Ignition "ON" & Engine "OFF".
5. Install scantool and select "EVAP PURGE VALVE" on the Actuation Test mode.
6. Activates "EVAP PURGE VALVE" by pressing "STRT(F1)" key.
7. Verify PCSV release vacuum while valve is activating(should hear a faint click from PCSV).
8. Repeat this procedure 4 or 5 times to ensure PCSV reliability.
9. Is PCSV working properly?
YES
? Go to "Canister Closing Valve(CCV) Line Inspection" procedure.
NO
? Verify arrow on PCSV is pointing towards intake manifold. If it is not, reverse installation. Reinstall as necessary.
? If OK, check for cracks or damage in hose connecting PCSV and intake manifold. Repair or replace as necessary.
? If OK, test with a new PCSV and check for proper operation. If problem is corrected, replace PCSV and go to "Verification of Vehicle Repair" procedure.
Canister Closing Valve(CCV) Line Inspection
1. Return vehicle to original condition.
2. Ignition "OFF".
3. Disconnect the hose connecting Canister Closing Valve(CCV) to canister.
4. Blow air to the canister side of the valve and verify air escapes to the air filter side.
5. Turn ignition on and jumper a wire to GND(back probe) at terminal 2 of the ECM connector(CCV valve should click).
6. Blow air into hose and verify air does not escape.
7. Repeat this procedure 4 or 5 times to ensure CCV reliability.
8. Is CCV working properly?
YES
? Go to "Fuel Tank Pressure Sensor Inspection" procedure.
NO
? Check for cracks or damage in hose connecting CCV and canister. Repair or replace as necessary.
? If OK, replace CCV. If CCV was stuck closed, inspect all lines and canister for liquid fuel. Replace any contaminated components and blow out lines and go to "Verification of Vehicle Repair" procedure.
Fuel Tank Pressure Sensor Inspection
1. Start engine and install scan tool.
2. Monitor "FUEL TANK PRESSURE" parameter on the current data list with depressing increasing engine speed.
Specification : Signal value will vary between -2mmHg to 2 mmHg depending on variation in engine speed.
A. Approx. 0~2 mmHg(2.5V) at Ig. On
B. Approx. 0 mmHg at 1400rpm .
C. Approx. -2 mmHg at 4000rpm.

3. Is signal value within specification?
YES
? Go to "PCSV to Canister Line Inspection" procedure.
NO
? Check for cracks or damage in hose connecting canister and fuel pump. Repair or replace as necessary.
? Check for open or short in FTPS harness. Repair as necessary.
If OK, test with a new FTPS and check for proper operation. If problem is corrected, replace FTPS and go to "Verification of Vehicle Repair" procedure.
PCSV to Canister Line Inspection
1. Check for leakage in hose.
(1) Disconnect the hose leading from the canister to the PCSV at canister.
(2) Using a vacuum pump, apply specified vacuum[Approx. 10cmHg(4 inHg)] to the manifold side of the valve and verify PCSV holds vacuum.
(3) Monitor vacuum pressure for 1 minute. After 1 minute, pressure should not drop more than 2cmHg(0.8 inHg).
(4) Is pressure within specification?
YES
? Go to "2. Check for leakage in canister" procedure.
NO
? Check for cracks or damage in hose connecting PCSV and canister. Repair or replace as necessary and go to "Verification of Vehicle Repair" procedure.

2. Check for leakage in canister.


Thoroughly check all fuel vapor hoses and hose clamps between:
1. Canister and fuel tank.
2. Canister and CCV.
3. Canister and PCSV.

If NG, replace hose or clamps as necessary and go to "Verification of Vehicle Repair" procedure.
If OK, go to next step as below.
(1) Disconnect hose clamps and remove canister assembly .
(2) Block the hose of between:
A. Canister and fuel filler neck.
B. Canister and CCV.
C. Canister and PCSV.

(3) Apply maximum of 10cmHg(4 inHg) pressure through fuel tank port from canister.
(4) With system sealed and pressurized, check for leaks.
(5) Were any leak(s) found?
YES
? Repair or replace leaking system component(s) and go to "Verification of Vehicle Repair" procedure.
NO
? Go to "Fuel Tank Line Inspection" procedure.

Fuel Tank Line Inspection
1. Relieve the fuel system pressure and remove the fuel tank.


Before removing the fuel tank, make sure the fuel hoses are not leaking.

2. Block all of the following outlets:
(1) Fuel lines.
(2) Fuel filler neck.

3. Apply maximum of 10cmHg(4 inHg) pressure to the EVAP. hose at the fuel tank. Then, pinch the EVAP. hose to retain the pressure.
4. Check the suspect area for leaks with a soap solution.
5. Were any leak(s) found?
YES
? Repair or replace leaking system component(s) and go to "Verification of Vehicle Repair" procedure.
NO
? Check for poor connection between ECM and component: backed out terminal, improper mating, broken locks or poor terminal to wire connection. Repair as necessary and go to "Verification of Vehicle Repair" procedure.

Posted on Jul 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hyundai santaFe 2.7 v6 ecu connection to speed sensor and selector corrupted and the vehicle jumps from gear 1 to 3 failsafe.It does not engage the reverse gear.When driving on the sport/steptronic it


is no need to match colors. Try by using a tester and see which wire is earth,signal and play with it. Confirm whether it is the right part first.

Aug 10, 2012 | 2002 Hyundai Santa Fe

1 Answer

Where to find the number on the fuse for n a 2002 hyundai santafe


GO TO HMASERVICE.COM & REGISTER YOUR VEHICLE BY VIN # YOU'LL THEN HAVE ACCESS TO WIRING DIAGRAMS, TSB'S (TECHNICAL SERVICE BULLETINS), SHOP MANUALS, ETC.

May 07, 2012 | Hyundai Santa Fe Cars & Trucks

2 Answers

2004 santa fe hyundai


it is probably going into a fail safe mode, get it to a dealer and have it scanned for dtc's

Apr 24, 2010 | 2004 Hyundai Santa Fe

1 Answer

I have an hyundai santafe 2004 I do not have a remote


Purchase another from your Hyundai dealer, You will need to take vehicle in to get key barrel number read and to reset new remote to your vehicle.

Dec 03, 2009 | 2004 Hyundai Santa Fe

1 Answer

Problem with indicators lamps


What is 'CRDi'?... never heard of it.

Jun 23, 2009 | 2004 Hyundai Santa Fe

1 Answer

2001 Hyundai SantaFe-wiring diagram


how I find the a/c diode for santa fe hyundai 2001

Dec 26, 2008 | 2001 Hyundai Santa Fe

2 Answers

My drivers side tail light is out on my 2004 sante Fe,


theres a short in the wireing causeing the fuse to blow gonna have to find the short

Dec 20, 2008 | 2005 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...