Question about Honda Cars & Trucks

Open Question

Torque crankshaft honda civic 1997how

How to propper tight bolt mainbearing

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Replacing head gasket on 1995 honda civic, require torque specs and secquence

wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

Posted on Jan 01, 2009

  • 158 Answers

SOURCE: 2000 sebring transmission pan torque spec

10 ft lbs no real patterm needed

Posted on Apr 03, 2009

  • 12 Answers

SOURCE: head bolt torque specs for 200 honda accord 3.0

its a three step process 1st 29ft/lbs 2nd 51ft/lbs 3rd 72.3ft/lbs

Posted on Apr 25, 2010

walleyracing
  • 76 Answers

SOURCE: hi what is the head torque on a 2002 honda civic

Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Posted on May 03, 2010

    • 334 Answers

    SOURCE: need torque specs for bolts

    Hello claudian1535,

    Below is an image showing the torque sequence. The torque procedure is a three step process:

    Step one torque all head bolts to 14 ft.lbs.
    Step two torque all head bolt to 36 ft.lbs.
    Step three torque all head bolts 49 ft.lbs.


    netvan_116.png

    I hope this helps.

    Regards,

    netvan

    Posted on Jul 23, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Hi im fixing a 89 honda civic have everything to put it back together but the torque settings for mains,connector rod bearings head stage 1,2,3 an the rest thanks


    CRANK SHAFT PULLEY BOLT TORQUE IS 83 FT LBS. MAIN BEARINGS TORQUE IS 48 FT LBS ROD BEARINGS TORQUE 23 FT LBS. YOU NEED A BEARING SEQUENCE GET PIECE OF PAPER WRITE NUMBERS 9 5 1 3 7 AND UNDER THIS NUMBER LINE NUMBERS UP ON EACH OTHER WRITE DOWN NUMBERS 8 6 2 4 10 YOU HAVE 10 CRANKSHAFT MAIN BEARING BOLTS. WHEN YOU LINE UP BOTH NUMBERS YOU WILL START TIGHTEN BOLTS 1 AND 2 TIGHTEN BOLTS 3 AND 4 TIGHTEN BOLTS 5 AND 6 TIGHTEN BOLTS 7 AND 8 TIGHTEN BOLTS 9 AND 10 YOU ARE TIGHTEN BOLTS IN A CRISS CROSS PATTERN. BESURE TO POUR OIL OR LUBRICATE CRANKSHAFT AND BEARINGS WITH CLEAN ENGINE OIL.WHEN YOU TORQUE MAIN BEARINGS TORQUE ALL THEM TO 20 FT LBS AND SECOND PASS TORQUE ALL BOLTS TO FINAL TORQUE 48 FT LBS. IF YOU RUN TO ANY PROBLEMS. YOU CAN BUY A HAYNES REPAIR MANUAL IT CAN HELP YOU.

    Mar 02, 2011 | 1989 Honda Civic

    1 Answer

    Just wondering if it is hard to rplace the crank shaft postion sensor on a 2000 honda civic. and were can i find this part on my car.


    It is at the bottom of the front of the engine. You have to take the timing belt cover off to get to it. The crankshaft pulley bolt is the hardest thing to remove as it has LOTS of torque holding it on. If you don't have the special tool to hold the crankshaft pulley in place or a powerful air impact gun, you won't be able to take the pulley off to get the timing cover off.

    Jan 27, 2011 | 2000 Honda Civic

    1 Answer

    Crankshaft pulley looses spontaneously producing belt damages and heavy noise. What is the procedure to tight it properly and what are the possible causes?


    It's apparent your crankpulley is coming apart, should be replaced. Torque crankpulley bolt around 180 ft/lbs. Inspect the belts for cracks and fraying.

    Jan 18, 2011 | 1998 Honda Civic

    2 Answers

    Connecting piston rod torqe1.0 engine rod rod spec


    PISTON ROD BEARING TORQUE 26 FT LBS CRANKSHAFT MAINBEARING TORQUE IS 40 FT LBS

    Jan 10, 2011 | 1996 Geo Metro

    1 Answer

    Torque para cabeza honda civic motor 1.6


    1996-97 Civic and Civic del Sol
    1.6L (D16Y5, D16Y7 and D16Y8) ENGINES

    Tighten the cylinder head bolts to their final torque specification in four steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows:
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the two center bolts to 49 ft. lbs. (67 Nm).

    Hope helps (remember to rate and comment this).

    Sep 23, 2010 | 1997 Honda Civic

    1 Answer

    Hi what is the head torque on a 2002 honda civic


    Dont forget to apply clean engine oil to the threads of each bolt for proper torquing. Then finger tighten. Then

    1. Tighten the cylinder head bolts to their final torque specification in 4 steps. Use a crisscross sequence starting with the bolts at the middle of the head and working toward the outer bolts as follows: Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).
    1. Step 1: Tighten each bolt to 14 ft. lbs. (20 Nm).
    2. Step 2: Tighten each bolt to 36 ft. lbs. (49 Nm).
    3. Step 3: Tighten each bolt to 49 ft. lbs. (67 Nm).
    4. Step 4: Retighten only the 2 center bolts to 49 ft. lbs. (67 Nm).


  • Mar 25, 2010 | 2002 Honda Civic

    1 Answer

    Cant break my crankshaft pully bolt is it left handed threads?1990 honda civic lx


    when it comes to hondas. the crank shaft pulley bolts are standard thread, which mean "righty tighty lefty loosy" THEY ARE ON THERE EXTREMELY TIGHT!!!!!. i myself have broken many air guns and breaker bars. your best bet would be to take it to a shop and let them break there tools.

    Oct 25, 2009 | 1990 Honda Civic

    2 Answers

    Replacing head gasket on 1995 honda civic, require torque specs and secquence


    wow. a lot of bad information on this site. Refer to a manual for the proper torque sequence. The civic I believe is a two step torque procedure. First 22 ft lbs, than 53 ft lbs.

    Sep 13, 2008 | 1995 Honda Civic

    2 Answers

    1991 honda civic timing belt


    I always used a high torque air inpact gun and it is not reverse thread.

    Jul 22, 2008 | 1991 Honda Civic

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    74896 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7688 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...