Question about Holden Cars & Trucks

2 Answers

Hi, I have a 2002 Holden Rodeo 2.2 L 2WD ute and I need to have a new ignition key programed for it.It only has the ignition immobilizer inbuilt into the key.Can I do it myself?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 197 Answers

I think you have to see holden for that on -- i had to for my commodore at one point which cost me $99 who would have thought keys would cost sooo much!! :C

Posted on May 08, 2017

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Holden Master
  • 42,190 Answers

Have you tried getting a blank key fob , getting the key cut and then putting the electronics in the new key fob of course if you have lost the key then the new key will have to be programmed with the car
some locksmiths can do that or else it is only done at the dealers

Posted on May 08, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why can't find water trap on rodeo second generation TF 1988 2003 Holden rodeo tray top


Not unless it was fitted after market. to make sure trace the fuel line from the fuel filter back to the tank.

Jul 08, 2014 | Holden Rodeo Cars & Trucks

1 Answer

Lost keys for Holden rodeo 1991, can I get replacement ones from Holden, or will I have to get a locksmith?


If you take the vin number to the dealer service department they may have the pin numbers for the key and so can give you the numbers so that a locksmith can machine a key for you . You may be able to get a locksmith to remove the tumbler and then he can read the pins to make a key for you. The only other way is to get a new tumbler for the ignition switch from holden and have the new keys programmed to suit the immobiliser in the car.

Jan 10, 2014 | 1991 Isuzu Rodeo

1 Answer

2003 HOLDEN RODEO UTE SHUTS DOWN WHEN DRIVING,WARNING LIGHT COMES ON ,BUT WILL START ONCE IT PULLS UP


have the fault codes read. Check for failed cat converter blocking exhaust.

Apr 03, 2013 | 2003 Isuzu Rodeo

1 Answer

I LOOST KEY TO MY HOLDEN RODEO LX 4X4 2002 IS IT A CHIP KEY


Unless you have one working key the lock cylinder must be replaced and the system programmed for the new code. You can't do this without the dealer.

Jun 27, 2012 | Cars & Trucks

1 Answer

Engine will not start after changing battery in 2004 Isuzu Rodeo


Get yourself a can of starting fluid spray, and spray NO MORE than a two second burst into the air intake after removing the filter. Then crank it. If it fires (very briefly), your problem is low or no fuel delivery to the engine.

May 16, 2017 | 2004 Isuzu Rodeo

1 Answer

Rodeo petrol starts but wont rev


Holden Rodeo 1989 2.6mpi , start and only runs for 2 or so seconds themselves stalls, after putting on a fuel peesure gauge, fuel looked okay and slowly dropping, found the ECM relay was intermittently switching on and off, gave it a tap and the engine kept on running, relay not repairable, replace with new part. Located in the fuse and relay box on the right hand side of engine bay next to battery. Hope this helps.

May 24, 2012 | Holden Rodeo Cars & Trucks

1 Answer

2002 holden rodeo automatic transmision oil capacity


The filter doesn't take any oil, but when they figure the quantity, they figure either filter change or rebuild, the filter change uses about 5 quarts and the rebuild is 12 quarts. I don't have the exact amounts in front of me, but if you need them,I can look them up. Also, I am not familiar with the Holden dual cab, But most automatics are about the same. Hope this helps.

Mar 08, 2010 | 2002 Isuzu Rodeo

1 Answer

Reprogramming remote and key


if its early 05 round heart shaped remote it needs programming into system at dealer with Tech2
later 05 to 07 had square (rectangle) shaped remote
1.2 ID Code Additional Registration
Note: This procedure will add additional remotes to the Keyless Entry Control Units memory. A total of 4 remote transmitters may be programmed into the Keyless Entry Control Units memory. When a total of registered and newly registered remotes exceed 4, the oldest one shall be erased.
Step Action
1 Note: Make sure that all the doors are closed and unlocked. Insert the ignition key into the ignition switch.
Open the driver's side door.
2 Turn the Ignition key to the “ON” position and then to the “LOCK” position three times
(The key should remain in the “LOCK” position)
Note: This step must be carried out within five seconds.
3 “CLOSE” and “OPEN” the driver’s doors once (Leaving the driver’s door in the “OPEN” position)
Note: This step must be carried out within five seconds after step 2 is completed.
4 Wait for 8 seconds (This wait time is critical)
5 Turn the Ignition key “ON” and then to the “LOCK” position once and turn key to the “ON” position (The key should remain in the “ON” position)
OR on/lock once
Note: This step must be carried out eight seconds after step 3 is completed.
6 “CLOSE” the driver’s door
The HAZARD lights should flash 3 times (This acknowledges the Keyless Entry Control Unit has entered programming mode)
7 Operate the lock or unlock button of the transmitters to be programmed; a flash of the HAZARD lights indicates the remote has been successfully programmed into the control unit
8 The HAZARD lights will flash approx 4 seconds after pressing the remote button to indicate the Keyless Entry Control Unit has exited programming mode.

Mar 26, 2009 | 2004 Isuzu Rodeo

1 Answer

Turn key and it doesnt fire


one way to find out. spray starting fluid in the intake then try to start. if it starts then your problem is fuel related.

Mar 11, 2009 | 2004 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Holden Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you a Holden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...