Question about Cars & Trucks

Open Question

Head Bolt Tension Conversion from Metric to Imperial for y60 TB 42

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: head bolt tension setting

these specs straight from service info
single cam
25Nm + 70deg+ 70deg+ 30deg
twin cam
25Nm+70deg+70deg+ 30deg

alot of after market gasket sets are the 25Nm and 3 lots of 60deg and the extra 10deg bolts are meant to be replaced (use once only) alot of bolts tend to start stretching when doing last 10 deg use oil on threads and washers under bolts 25 and 3 lots of 60deg is correct and more commonly used.

Posted on May 28, 2009

Ad
  • 83 Answers

SOURCE: Looking for Jeep TJ 4.0litre head bolt tension and

First tighten to 25 ft/lbs then 50 then 85 except number 8 bolt only 75 lbs front 9   8 5   6  1   2 3   4 7   10

Posted on Oct 25, 2009

  • 2 Answers

SOURCE: What kind of bolt is holding the tension pulley on

1/2 inch is metric???

Posted on Dec 04, 2009

  • 72 Answers

SOURCE: timing marks, head bolt tension.specifications

Hi, I have a daihatsu rocky and the best source of information for Daihatsu has come from a site called WARFS.ORG when you go to the site you will see that there is a link for diahatsu help Leon is the US rep for them and the man knows more about daihatsu's than anyone on the planet.I hope this helps you good luck and keep that daihatsu running !!

Posted on May 12, 2010

radar001
  • 1051 Answers

SOURCE: Need to replace head gasket

I frequently use and highly recommend registering for free at www.autozone.com Your registration gives you access to a variety of repair and shop manuals, most giving you detailed repair instructions diagrams and specs.

Posted on Jul 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head bolt tension for 2010 Mitsubishi FN64F 6M60-3AT2


The term you mean is actually torque. Cylinder head torque is usually specified in foot pounds, or in the metric world, newton meters. It describes how much twisting force should be applied to tighten the head bolts.


www.engineaustrailia.com.au/products/diesel-engine-parts/mitsubishi

Apr 20, 2017 | Mitsubishi Cars & Trucks

2 Answers

How do you change from metric?


Move to a non Imperial Country.

Jan 19, 2017 | Cars & Trucks

1 Answer

Does anyone know what size bolt holds the high pressure hoses on under the ps pump on a 03 chevy trailblazer? Have tried every known tool I have. Invert torx,stand,metric. Thank you


You remove the high pressure line using a standard imperial open ended spanner on the fitting where the steel HP line attaches to the PS pump unit.. It will most likely be around 5/8". But, if not that size, if you have a decent range of imperial size open ended spanners you should have no problem finding one that fits perfectly. If you don't in your spanner set then slide an adjustable spanner over the fitting, adjust it up to the bolt on the HP line and then remove and measure the size. Buy a spanner that size (the longer the better) and you should have no issue removing the line as long as the bolt head has not been rounded off.

Jan 28, 2016 | Cars & Trucks

1 Answer

Where is the alternator on a 2003 chrysler concord and how do you change it what tools do i need


FIRST TURN OFF RADIO THEN DISCONNECT NEGATIVE BATTERY CABLE.IF YOU HAVE 2.7L ENGINE YOU HAVE TO REMOVE LOWER PLASTIC SPLASH SHIELD, REMOVE TRANSMISSION COOLER AND POSITION IT ASIDE.LOWER RADIATOR CROSSMEMBER SUPPORT, LOOSEN DONT REMOVE,ADJUSTING T BOLT AND THE PIVOT BOLT LOOSEN BELT ADJUSTING BOLT, REMOVE DRIVE. REMOVE ALTERNATOR FIELD CIRCUIT PLUG. REMOVE ALTERNATOR BATTERY PLUS TERMINAL NUT AND WIRE REMOVE.PIVOT BOLT SPACER CAREFUL DONT DROP LOSE SPACER. THEN REMOVE ALTERNATOR. YOU NEED BELT TENSION GAUGE TORQUE ADJUSTING T BOLT UNTIL TENSION GAUGE READS 120 LBS USED BELT NEW BELT 180 - 200 LBS. YOU NEED ALL BASIC MECHANIC TOOL SET WITH METRIC SOCKETS METRIC OPEN BOX END WRENCHES.SIZE WRENCH RANGE 5MM UP TO 19MM NEED ADJUSTABLE PLIERS NEED SCREW DRIVERS LIKE FLAT HEAD AND PHILLIPS. YOU NEED TORQUE WRENCH. FOR THE PIVOT BOLT NEED TORQUE TO 40 FT LBS. THE 8MM MOUNTING BOLT TO 30 FT LBS. 10MM BOLT TO 40 FT LBS.

Sep 08, 2011 | 2000 Chrysler Concorde

1 Answer

Need to replace head gasket and require Nissan Patrol Y60 TD42 engine Head bolt torque specs


I frequently use and highly recommend registering for free at www.autozone.com Your registration gives you access to a variety of repair and shop manuals, most giving you detailed repair instructions diagrams and specs.

Jul 21, 2011 | Nissan Pickup Cars & Trucks

1 Answer

I have a 95 rodeo 2.8td just need to know head bolt torque setting


Cylinder Head-

1st Head-- 40-42 ft.lbs 54-57Nm(metric)

2nd Head-- tighten each bolt to specifications as above plus tighten and additional 90 degrees.

Jan 23, 2011 | Isuzu Rodeo Cars & Trucks

2 Answers

What are the torque specs for belt tensioner


There no real specs for the tensioner. The bolt should be tight and the unit as a whole should be squared to the engine. If it is in anyway tilted, th eunit is coming apart and will need to be replaced. One bolt holds this unit in place. It should have adequate tension to keep the belt taunt against all the pullies. If you are dealing with a constant squeel issue, locate the writing and you should be able to read it like holding a book in your hand. If it is upside down to you, reinstall. this will take care of the squeeling 9 times out of 10. The tensioners for replacement run about $50 - $75.

Oct 23, 2010 | 2005 GMC Sierra

1 Answer

How do you change the steering wheel on the bf falcon without setting the airbag off?


First disconnect the battery positive lead. Then you will have to remove the lower steering column shroud - philips screwdriver. Then you will see two tork screws behind the steering wheel. Remove these and the airbag will come out. Disconnect the three elect' plugs and the airbag will come free. Wheel centre bolt is also a tork bolt but I used an imperial allen key (5/16 if I remember correctly) to loosen it but didn't take it right out. Then a wheel puller with the centre screw resting against the tok bolt head to loosen the wheel, (two metric bolts screw into the wheel hub) remove the puller, remove the tork bolt and the wheel should come off easy. Good luck.

Jan 16, 2010 | 2005 Ford Futura

2 Answers

Conversion fom metric tyre to imperial tyre


If you have the factory tire size of 26.6x8.9/16 your new size will be 225/60/16
26.6x8.9/16 =225/60/16


Please rate this a fixya

Jan 30, 2009 | 1994 Jaguar XJ6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...