Question about Toyota 4Runner

Open Question

Right brake light will not come on and have changed bulb, left works fine. Has to be connection or wiring? Need suggestions. 2011 Toyota 4Runner

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Chev Cavalier 2003 only one rear turn/brake/hazard light

I have a 2002 Chev Cavalier that had the same exact problem. I replaced the bulb harness (purchased from a chevy dealership for around $5) which was fairly easy to do. I have had zero problems with it since.

Posted on Dec 03, 2008

moparownr
  • 667 Answers

SOURCE: Right brake light out; tail light works fine

most rear tail lights and turn/stop lights are the same dual filiment bulb. it is possible for your tail light to work and your brake light not to and still have a bad bulb. I would check the bulb first, your brake light works on the left yes? this would mean that the fuse is fine

Posted on Mar 31, 2009

  • 150 Answers

SOURCE: 2005 Toyota Sienna rear brake light problem.

have you checked the earthing continuity-if it's this other bulbs may also partly light when brakes used
otherwise-
Check continuity of live from center to lh & rh lights and/or is there a live at those lights

Posted on May 03, 2009

  • 28 Answers

SOURCE: 2003 Toyota Highlander.The brake light on the

Replace the right rear brake lamp. The bulb possible use two filaments one for brake and tail light. One burnt out filament in one bulb.

Posted on Nov 30, 2009

  • 10865 Answers

SOURCE: Brake light, reverse light and turn signal issues

Hello. The symptoms you are describing are likely due to a poor ground. Temporarily install a new ground wire by securing a piece of copper wire to the frame with a self tapping screw. Use this ground wire along with the hot wire to see if each of these lights works. If it does, trace the ground wire back to the frame, unscrew it and clean up the metal with emery cloth so you reestablish a good ground.

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The brake lights dont work changed fuse & bulbs could it be brake ligh switch on a 99 nissan Quest mini van


I can a similar problem in a toyota 4runner, i did the same changed the bulbs and fuse, but turn out to be the brake switch. The switch on the 4rummer was located under the dashboard where the brake pedal makes contact with the switch which was on its own bracket. The switch was white in color made of plastic and used 1/2" nut to secure it in the bracket and one wire connection.

Feb 05, 2015 | Nissan Cars & Trucks

1 Answer

Rear tail lights/wiring


check the light bulbs (filiments can break and touch the other filament in the bulb and backfeed other circuits) if they appear ok remove the non working bulbs and swap positions with the working bulbs and see if anything changes

Apr 04, 2013 | Cars & Trucks

1 Answer

Left brake lights may have short in wire ( not working)


Not a short, or both brake lights would not work. I suggest you have a defective bulb socket or bad socket ground, check the ground at the socket.

Oct 19, 2012 | 1999 Chevrolet Malibu

1 Answer

No brake lights after changing rear end on 96 4 runner


Since you were just working in the general area. I would check all wiring connections underneath, and around the axle!
It's a common happening, bump a connector without realising and things happen!
Good luck

May 30, 2012 | 1996 Toyota 4Runner

1 Answer

I have a 2003 Highlander. Both brake lights on the left do not turn on. When I swap the bulbs from the left with the right brake lights, the left side brake lights still do not turn on. Any suggestions on...


You have a problem in the wiring at these bulbs. Since all of them aren't working then the problem is between the bulbs and the ground: the wires that go from the bulbs to the body of the car are either no longer attached to it or the connection(the bolt that tightens them on the body) is covered in rust and that insulates it.
Find the connection bolt by following the wires, clean it with wire wool then unscrew it an clean the copper connectors from the wires and the body with fine sandpaper until the metal shines. put all back together and cover it in grease to protect it against future damage.
BTW you can't get the bulb out because the corrosion has got in there also: just force the bulb out and then clean all the bulb slots with sandpaper until they shine. Don't forget the brass blades from the bottom of the slots, the ones that make contact with the plots on the bulbs.

Nov 05, 2010 | 2002 Toyota Highlander

2 Answers

I need a FREE 1992 Toyota Camry taillight wiring diagram. My side rear park lights come on but my park lights that work with the brake lights don't. I changed the bulbs and tested everything. I narrowed it...


brown wire is your park LT yellow Left-turn green right-turn. Now the break light my be on it own wire it is red black is ground. but if you have a test light see if the brown wire turns on the test LT when you turn on the park LT or what wire light up when you step on the break pedal. and so on.

Feb 25, 2010 | 1992 Toyota Camry V6

2 Answers

No brake light one side


It is likely that the bulb is just out as the left and right brake lights would be on the same circuit. Unless there is a strange wiring issue simply replacing the bulbs should correct your problem.

Apr 18, 2009 | 2008 Toyota Highlander

1 Answer

Passenger side turn signal not working on 2003 Toyota 4Runner


right above your left hand foot if your not a brit in the UK or so.
Some cars have 2 units. Simple short test with a mulimeter will point out which one or both or other problem.

Apr 01, 2009 | 2003 Toyota 4Runner

1 Answer

How to fix a brake light


all lights must be working in order for the lights to work in some cars...it's possible that you may have a bad ground wire to the light socket or the you may not be getting power to that socket, which means you have a bad wire. Check to see if you're getting power to that socket with an electrical tester first.

Mar 17, 2009 | 1998 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...